Industrial Equipment Experts Since 1980 | Mon–Fri, 7 AM–6 PM ET
No bots. Real experts. 866-333-0728
Get a Fast Quote
Get a Fast Quote

CustomMHS Buyer's Guide

Bulk Containers

Collapsible, rigid, sheet metal and wire mesh. How to pick a footprint, read the load ratings that are not the same thing, and put a number on what collapsing saves you.

Covers: Buckhorn · Monoflo · Triple Diamond · Orbis · Davco · Worldwide · Vestil · Little Giant Questions: 866-333-0728 Written and reviewed by: Tom McGovern · November 2026
Section One

Three decisions, in order

A bulk container is a big purchase multiplied by fleet size. Getting the order of decisions right saves the most money.

Quick answers
  • Pick the footprint first. It is set by your pallets, racking, trailers and often your customer.
  • Buy collapsible if empties travel or get stored, and rigid if they never do. One published wire bin fits 144 upright or 324 collapsed on a 53 ft truck.
  • Load capacity is what goes inside. Stack limits are separate. Where the manufacturer publishes a maximum stack height, use it.
  • Plastic bulk containers we list carry 1,200 to 2,500 lb. Sheet metal and wire carry 2,500 to 5,000 lb.

These are the largest containers in material handling: roughly a pallet footprint, holding from 14 to about 40 cubic feet, and rated from 1,200 to 5,000 lb on the models we list.

Almost every good outcome in this category comes from settling three questions in this order:

First

What footprint?

Set by your pallet, your racking, your trailer and often your customer. It limits everything after it, so decide it before you look at a single product.

Second

Collapsible or rigid?

Driven by what happens on the empty leg. If empties travel or get warehoused, collapsing pays. If they never do, rigid is simpler.

Third

What material and access?

Plastic, sheet metal or wire, and how product gets in and out. These follow from the load, the environment and the process.

Buyers often reverse this, starting from a product they saw and working backward. That is how you end up with a container that holds the right volume, carries the right weight, and does not fit your pallet or your rack bay.

Please read this part

This guide is educational and reflects the opinion and general experience of CustomMHS as an equipment distributor. It does not replace the manufacturer's instructions, your rack capacity plaque, or your facility's written safe work procedures. Sizes, load ratings and stack limits are the manufacturers' published figures and can change. Confirm the current data sheet for your exact model before you order or stack.

Section Two

Collapsible or rigid

The empty leg decides this, and you can measure it.

Short answer: If empty containers ride a trailer or sit in a warehouse, collapsible containers usually pay for themselves in freight and floor space. If empties never leave the work cell, buy rigid.

What collapsing buys you

A collapsible bulk container folds its walls down onto the base when empty. The published numbers are large. The Buckhorn BH48453400 stands 34 in tall and 13.6 in collapsed. The Monoflo BC4844-34 is 33.8 in tall and 12.5 in collapsed. The Buckhorn Intrepid BZ is 45.9 in tall and 13.8 in collapsed, a published 3.3:1 return ratio.

The clearest example is a wire bin. Davco publishes truckload figures for the KDW-01: 144 upright bins on a 53 ft truck, or 324 collapsed. That is 2.25 times as many containers per trailer on the return leg.

Worked example: return trips saved
  • Formula: loads when collapsed = loads when upright × (upright per truck ÷ collapsed per truck).
  • Numbers: you run 100 empty-return loads a year. 100 × (144 ÷ 324) = about 45 loads.
  • Result: about 55 trailer loads saved every year. Run this before you compare unit prices.

Where each type wins

Collapsible: empties travel or get warehoused
Walls fold onto the base. Costs more per unit and adds hinges and latches that can be damaged. Pays back through return freight and floor space. The usual choice for returnable programs.
Rigid: containers stay loaded, or stay put
Fixed walls, nothing to fold and no setup step. Empties take full space, so this is the wrong answer if you ship them back. See Buckhorn fixed wall containers and Davco rigid sheet metal and wire bins.

One naming note: Davco calls some of its folding steel and wire bins "knock down." On our listings those fold down when not in use, the same idea as collapsible.

The hidden cost of collapsible: the fold itself

Every collapse and set-up is a handling step. If operators cycle containers many times a day, those seconds add up and the folding hardware wears. Ask how the walls fold, whether they have to fold in a set order, and whether the container stacks when collapsed.

The question to ask

How many empty containers move or sit idle in a typical month, and where? If the answer involves trailers or warehouse floor, price the collapsible and run the trip math above. If empties never leave the cell, rigid is the simpler buy.

Section Three

Footprint: pick it first

The most limiting decision, and the one buyers most often leave until last.

Short answer: Use 48 in × 45 in for automotive, 48 in × 40 in for grocery and retail pallets, and 32 in × 30 in when a full-size container gets too heavy. Then choose height by product density.

Bulk containers are sized to pallet footprints because they live on pallet equipment: your racking, your forklifts, your trailers and your customer's dock.

Footprints we list, with published load ratings
Footprint Load ratings Where it fits
32 in × 30 in 1,500 to 2,000 lb Half-size plastic. Good where full-size containers are too heavy to fill safely, or you want smaller lots per part number.
48 in × 40 in 1,200 to 2,500 lb The standard grocery pallet footprint. The usual choice for food, beverage and retail distribution.
48 in × 45 in 1,500 to 2,500 lb The automotive standard, and the widest model selection we list.
40-1/2 in × 34-1/2 in 2,500 to 3,200 lb The common Davco sheet metal and wire bin footprint.
54 in × 44 in 5,000 lb Oversized rigid wire for heavy, bulky material.

Height is the free variable

Within a footprint, height is where you match volume to your product. The Buckhorn BN series in 48 in × 45 in comes in 25, 34, 39, 41, 44 and 51 in heights, with interior heights from 18.3 in to 44 in.

Notice the ratings in that family: the 25 in and 34 in models are rated 2,500 lb, and the 39 in and taller models are rated 2,000 lb. Taller does not mean stronger. Read the rating for the exact height you are buying.

Density decides height

A common error is picking height by how much product you want to move, then finding the container hits its weight rating half full. Run the arithmetic first.

Worked example: how deep can you fill before you hit the rating?
  • Floor area: the BN series interior is 44.5 in × 41.5 in. That is 3 ft 8-1/2 in × 3 ft 5-1/2 in, or about 12.8 square feet.
  • Formula: fill depth in feet = rated load ÷ (product weight per cubic foot × 12.8).
  • Light product, 30 lb per cubic foot: 2,500 ÷ (30 × 12.8) = 6.5 ft, or 78 in. No model is that deep, so you will fill it before you weigh it out. Buy the height you need for volume.
  • Dense product, 100 lb per cubic foot: 2,500 ÷ (100 × 12.8) = 1.95 ft, or about 23 in. The 34 in model, with 27 in inside, is nearly full at its rating.
  • Same dense product in the 51 in model: it is rated 2,000 lb, so 2,000 ÷ (100 × 12.8) = about 19 in of fill in a 44 in deep container. You would be shipping mostly air.
Standardize where you can

A fleet on one footprint fits the same pallet, the same rack bay and the same dolly, and stacks with itself. If you need two sizes, pick a full size and its half size.

Section Four

Materials: plastic, sheet metal, wire

Three families with very different strengths.

Short answer: Plastic is light, washable and will not rust. Sheet metal carries more and takes sharp or hot parts. Wire carries the most and lets you see and drain the contents.

Plastic

The main material for collapsible bulk containers. Better containers put steel where the loads concentrate: the Buckhorn BH48453400 has a reinforced base with three steel runners and steel corner hit plates that deflect fork tines.

Plastic wins on weight, cleaning and corrosion. Load ratings on the plastic containers we list run from 1,200 to 2,500 lb. Watch the empty weight, since it is freight on every leg: the BH48453400 weighs 163 lb and the Monoflo BC4844-34 weighs 118 lb.

Sheet metal

Steel walls on a tubing base. The Davco KD2GS-01 collapsible sheet metal container is 40-1/2 in × 34-1/2 in × 32 in, holds 18 cubic feet and carries 3,200 lb, with a zinc galvanized finish and safety edges on the walls.

Choose sheet metal for heavy, sharp or abrasive material and for rough handling. Solid walls hold small parts and debris that wire would let through.

Wire mesh

Open mesh on a steel frame with a sheet metal floor. Davco wire bins use a 2 in × 1 in mesh on all four sides. The KDW-01 carries 3,200 lb, the Davco GM-5131 rigid basket in 54 in × 44 in carries 5,000 lb, and Worldwide wire mesh containers run up to 4,000 lb.

  • Visibility. You can read the fill level and identify the contents from across an aisle.
  • Airflow and drainage. Important for wet parts and anything that would sweat in a closed container.
  • The limit. Small parts fall through a 2 in × 1 in mesh.
Material comparison, from the models we list
Material Published load ratings Strengths Limits
Plastic 1,200 to 2,500 lb Light, washable, will not rust, FDA option Lower load ceiling
Sheet metal 3,200 lb High load, holds small parts and debris, takes abuse Heavier and louder than plastic
Wire mesh 2,500 to 5,000 lb Highest loads, full visibility, airflow, drainage Small parts fall through
Section Five

The two load ratings

If you read one section, make it this one. Mixing these numbers up is how stacks fail.

Short answer: Load capacity tells you how much goes in one container. It does not tell you how high you can stack. For stacking, use the manufacturer's published stack limit for your exact model.

What each rating means
Rating Answers Governs
Load capacity How much product goes inside one container How full you can fill it
Stacking capacity How much weight the container can carry on top of it How high you can stack
Stack height The most containers allowed in a column The practical limit, when the manufacturer publishes it

Some manufacturers publish a stack height outright, which removes the guesswork. Davco publishes a maximum stack height of five full bins for both the KD2GS-01 and the KDW-01. Where the manufacturer gives a number, use it.

Where only a stacking capacity is published, divide it by the gross weight of one loaded container. Gross weight is the load plus the container's own weight.

Worked example: gross weight
  • One container: a BH48453400 filled to its 2,500 lb rating weighs 2,500 + 163 = 2,663 lb.
  • Three in a column: the bottom container carries two above it, 2 × 2,663 = 5,326 lb. Leaving out the empty weight would understate that by 326 lb.
  • The floor or rack: the full column weighs 3 × 2,663 = 7,989 lb.
Three things that void a stack rating
  • Uneven loading. Ratings assume the load is spread evenly.
  • Uneven floor. Ratings assume a level surface and a square, plumb column.
  • Damage. A container with a cracked base, a bent runner or a damaged corner no longer carries its rating. Pull it out of service.

Two more points. Limits for stacking collapsed containers can differ from loaded limits, so check them separately. And if containers go into pallet racking, the limit that governs is the rack's rated capacity. That is a question for your rack capacity plaque and your rack supplier.

Section Six

Getting product in and out

Access is decided by the process at both ends, and it is hard to change later.

Short answer: Choose drop doors where people reach in to pick. Choose a container with no door where product is poured or tipped, and respect the fill line when you stack.

Drop doors

A hinged section of wall that drops open so an operator can reach in without a forklift and without climbing. On a container about three feet deep, that is the difference between a good pick and a bad one.

The details vary. The Buckhorn BH48453400 has two drop doors on the length side, each 27.1 in wide by 14 in deep. The Davco KD2GS-01 has half-drop gates on both 34-1/2 in sides. Specify by asking where the operator stands and how far they have to reach.

Top load and discharge

Some containers are built without a drop door on purpose. The FDA Buckhorn Intrepid BZ has no drop door and discharges from the top. If your product is poured or tipped, not picked, you do not need a door.

Fill line

Easy to miss on a spec sheet. The Monoflo BC4844-34 has 27.9 in of interior height and a published fill line at 27 in. Filling a stacking container to the rim can keep the container above from seating.

Match access to both ends of the process

Buyers often specify access for how the container gets filled and forget how it gets emptied, or the reverse. Walk both.

Section Seven

Bases, forklifts and dollies

The base takes the abuse. It deserves more attention than it usually gets.

Short answer: Confirm four-way fork entry, look for steel where forklifts hit, and size any dolly to the gross weight: the load plus the container.

Four-way entry

A four-way base accepts forks from any side. The Buckhorn BH48453400 has a four-way base for fork trucks and pallet jacks. Confirm it for your model, and confirm pallet jack use if you rely on jacks.

Runners and hit plates

The base is where forklift damage happens. Three steel runners and steel corner hit plates, as on the Buckhorn BH series, are a good benchmark for a heavy-duty plastic container.

Dollies

A dolly lets a person reposition a container at a pick face or in staging where a forklift is impractical. Match the dolly to the container's gross weight, not its net load.

Bulk container dollies we list
Dolly Published capacity Suits
Little Giant bulk container dolly 3,600 lb Plastic containers at full load plus the container weight
Vestil bulk container dolly 8,000 lb Steel and wire containers and heavier loads

A 2,500 lb container that weighs 163 lb empty is 2,663 lb gross, inside a 3,600 lb dolly. A 5,000 lb wire basket is not, and needs the heavier unit.

Section Eight

Covers, placards and food grade

Usually an afterthought, sometimes the thing that makes the system work.

Short answer: Covers and placards are specific to the footprint and series, so order them with the containers. For food contact, buy a container published as FDA approved and confirm the model and color.

Covers

Covers keep contents clean and contained. They are footprint-specific, and some fit more than one series: the Buckhorn 48 in × 40 in cover fits the BH, BI and BG series. We also list 45 in × 48 in covers. Confirm the fit against your exact series.

Identification placards

Bulk containers are large and move constantly, and unlabeled ones become mystery inventory. I.D. label placards give you a durable, swappable label that holds up better than an adhesive label on a textured wall.

Food grade and FDA

Containers for direct food contact are a different specification, not a premium version of the same box. The Buckhorn Intrepid BZ series is the example we list: FDA approved polypropylene, 48.1 in × 40.1 in × 45.9 in outside, 40.5 cubic feet or 300 gallons, with no drop door and top discharge. It comes in a 2,000 lb model and a 2,500 lb model with steel inserts.

Confirm the specific model and color

FDA approval attaches to a specific resin and often a specific color, not to a manufacturer or a product family. Ask us for documentation on the exact model you are quoting, and confirm it covers your product and your cleaning process.

Section Nine

Choosing by application

Find the row that matches your situation.

Short answer: Footprint comes from your customer and your pallets, collapsible or rigid from the empty leg, material from the load, and height from product density.

Returnable program with a real return leg
Collapsible plastic. Run the trailer math in section two before comparing unit prices.
Automotive supply
48 in × 45 in footprint. Choose height by product density, not volume alone.
Food, beverage or retail distribution
48 in × 40 in footprint. For direct food contact, an FDA approved container such as the Buckhorn Intrepid BZ.
Heavy, sharp or abrasive material
Sheet metal or wire at 3,200 lb and up. The plastic containers we list top out at 2,500 lb.
Wet parts or post-wash staging
Wire mesh, for drainage and airflow.
Frequent counting or visual inventory
Wire mesh. You can read the fill level from the aisle.
Very dense product
A short container. Run the density math in section three.
Light, bulky product
A tall container, but check the rating. In the BN series the taller models are rated 2,000 lb, not 2,500 lb.
Operators pick parts out by hand
Drop doors, placed for where the operator stands.
Container gets tipped or poured into a hopper
No drop door needed. Top discharge.
Containers stay in one cell and never ship
Rigid. Nothing to fold and no setup step.
Repositioned by hand at a pick face
Add a dolly rated for gross weight. 3,600 lb covers a loaded plastic container. Heavy steel and wire need the 8,000 lb unit.
Full-size containers are too heavy to fill safely
32 in × 30 in half-size containers.
Section Ten

Stacking safely

These are the heaviest containers on your floor. A failed stack is a serious incident.

Short answer: Follow the manufacturer's published stack limit, stack square on level ground, respect the fill line, and never stack a damaged container.

  • Use the manufacturer's stack height where one is published. Davco publishes five full bins maximum for the KD2GS-01 and KDW-01.
  • Include the container weight in any calculation you make.
  • Respect the fill line. Product above it can keep the container above from seating.
  • Load evenly. Ratings assume the load is spread evenly.
  • Stack square and plumb, on level ground.
  • Never stack a damaged container, and never put one at the bottom.
  • Check collapsed stack limits separately.
  • Check the rack capacity, not just the container capacity, if containers go into pallet racking.
  • Inspect on a schedule and after any impact: bases, runners, corners, hinges and latches.
  • Train the fold. Collapsible containers only pay off if operators fold and set them up correctly.
Worth stating plainly

Stacking practice, rack loading and container inspection belong in your facility's written safe work procedures, matched to the manufacturer's published limits for the exact models you own. This guide does not replace those documents, a rack capacity assessment, or the manufacturer's instructions.

Section Eleven

Common and costly mistakes

Expensive at this size, and all avoidable before the order.

Short answer: The big ones are treating load capacity as a stack rating, choosing the footprint last, and sizing by volume when the product is dense.

Confusing load capacity with stacking capacity

Load capacity is what goes inside. Stack height comes from the stacking limit.

Forgetting the container weight

At 118 to 163 lb on the plastic models in this guide, it counts in stack math and in freight.

Choosing the footprint last

Footprint is set by pallets, racking, trailers and customers. Decide it first.

Assuming taller means stronger

Within one family, taller models can be rated lower. Read the rating for the exact height.

Sizing by volume when the product is dense

Dense material reaches the weight rating long before it fills a tall container.

Buying collapsible without a return leg

If empties never travel or get stored, you are paying for folding hardware you will not use.

Buying rigid when you do have a return leg

At 144 upright against 324 collapsed per trailer, the freight difference repeats every year.

Specifying access for only one end of the process

Walk both the fill and the empty.

Overfilling past the fill line

It can keep the container above from seating.

Ordering containers without covers, dollies or placards

All are model-specific and bulky to ship separately.

Assuming FDA approval covers a whole product line

Confirm it for the model and color.

Section Twelve

Frequently asked questions

What comes up most often on quote calls.

What is the difference between load capacity and stacking capacity?

Load capacity is how much product goes inside one container. Stacking capacity is how much weight that container can carry on top of it, and that limits stack height. Where a manufacturer publishes a maximum stack height, such as five full bins on Davco KD2GS-01 and KDW-01 bins, use that number.

How much space does a collapsible container save?

Published examples: the Buckhorn BH48453400 goes from 34 in to 13.6 in, the Monoflo BC4844-34 from 33.8 in to 12.5 in, and the Buckhorn Intrepid BZ from 45.9 in to 13.8 in, a published 3.3:1 return ratio. In freight terms, Davco publishes 144 upright or 324 collapsed KDW-01 bins on a 53 ft truck.

Which footprint should I choose?

Let your pallets, racking and customer decide. 48 in × 45 in is the automotive standard. 48 in × 40 in matches the standard grocery pallet. 32 in × 30 in is a half-size format. Davco steel and wire bins are 40-1/2 in × 34-1/2 in, with a rigid wire basket at 54 in × 44 in.

Is a taller container always higher capacity?

No. In the Buckhorn BN series, the 25 in and 34 in models are rated 2,500 lb and the 39 in through 51 in models are rated 2,000 lb. Read the rating for the height you are ordering.

Plastic, sheet metal or wire?

Plastic for general use: light, washable and it will not rust, with ratings from 1,200 to 2,500 lb on the models we list. Sheet metal for heavy, sharp or abrasive material at 3,200 lb. Wire mesh for the highest loads, up to 5,000 lb, plus visibility, airflow and drainage.

Do I need drop doors?

If operators reach in to pick, yes, placed for where the operator stands. If the container is tipped or poured, no. The FDA Buckhorn Intrepid BZ has no drop door and discharges from the top.

What is a fill line?

The highest fill level the manufacturer publishes for the container. The Monoflo BC4844-34 has 27.9 in of interior height and a 27 in fill line. Mark it on the container if operators fill by eye.

Can I put bulk containers in pallet racking?

Often yes, but the limit that governs is the rack's rated capacity, not the container's. Check your rack capacity plaque, and ask your rack supplier if you are unsure.

What dolly rating do I need?

Size to gross weight, which is the load plus the container. A 2,500 lb container that weighs 163 lb empty is 2,663 lb gross and fits a 3,600 lb dolly. A 5,000 lb wire basket needs the 8,000 lb unit.

How many containers do I need?

Count containers in every state: loaded and staged, in transit, empty and waiting to return, being cleaned, and in reserve. A closed loop needs enough to cover the full cycle plus a buffer.

Are these containers food safe?

Only specific models. FDA approval attaches to a particular resin and often a particular color. The Buckhorn Intrepid BZ series is published as FDA approved polypropylene. Confirm the exact model and ask us for documentation.

Section Thirteen

Quick-reference spec table

Published figures for products referenced in this guide. Confirm the exact model before ordering, since specs vary within every line.

Published specifications, sizes in inches (length × width × height)
Product Size Published load Notes
Buckhorn BH48453400, collapsible plastic Outside 47.6 × 44.6 × 34. Inside 44.3 × 41.3 × 27.1. Collapsed 13.6 2,500 lb 163 lb empty. Two drop doors, 27.1 × 14. Three steel runners, steel corner hit plates, four-way entry.
Buckhorn BN series, collapsible plastic 48 × 45 footprint. Heights 25, 34, 39, 41, 44, 51. Inside 44.5 × 41.5 2,500 lb at 25 and 34. 2,000 lb at 39 and taller Structural foam side panels, injection-molded welded base.
Buckhorn Intrepid BZ, collapsible, FDA Outside 48.1 × 40.1 × 45.9. Inside 45.0 × 37.0. Collapsed 13.8 2,000 lb, or 2,500 lb with steel inserts FDA approved polypropylene. 40.5 cu ft, 300 gallons. No drop door, top discharge. 3.3:1 return ratio.
Monoflo BC4844-34, collapsible plastic Outside 48 × 44.5 × 33.8. Inside 44.5 × 41.5 × 27.9. Fill line 27. Collapsed 12.5 1,800 lb 118 lb empty. 28.9 cu ft. Also in 25, 41.8 and 49.8 heights.
Davco KD2GS-01, collapsible sheet metal 40-1/2 × 34-1/2 × 32 3,200 lb 18 cu ft. Half-drop gates on both 34-1/2 sides. Zinc galvanized. Maximum stack five full bins.
Davco KDW-01, folding wire mesh 40-1/2 × 34-1/2 × 26 3,200 lb 14 cu ft. 2 × 1 mesh, sheet metal floor. 144 upright or 324 collapsed per 53 ft truck. Maximum stack five full bins.
Davco GM-5131, rigid wire mesh 54 × 44 footprint 5,000 lb Single gate.
Container dollies See listing Little Giant 3,600 lb. Vestil 8,000 lb Size to gross weight.
Product families we list
Family Footprint Published load Lines
Collapsible plastic 32 in × 30 in 1,500 to 2,000 lb Monoflo BC, Triple Diamond, Buckhorn BN, Orbis KD
Collapsible plastic 48 in × 40 in 1,200 to 2,500 lb Buckhorn BG, BH, BZ (FDA)
Collapsible plastic 48 in × 45 in 1,500 to 2,500 lb Monoflo BC, Triple Diamond, Buckhorn BN, BH, BE, BR
Fixed wall plastic 28.8 in × 41.8 in, 44 in × 48 in See listing Buckhorn BF
Sheet metal 40-1/2 in × 34-1/2 in 3,200 lb Davco KD2GS, KDS, R2GS
Wire mesh 40-1/2 in × 34-1/2 in, 54 in × 44 in 2,500 to 5,000 lb Davco KD2GW, KDW, R2GW, GM-5131. Worldwide up to 4,000 lb
Container dollies See listing 3,600 to 8,000 lb Little Giant, Vestil
Before you order

Figures above are as published on our product pages and by the manufacturers, and are subject to change. For stack ratings, collapsed heights, cover fit or FDA documentation on a specific model, call and we will pull the data sheet.

About the author. Tom McGovern has worked in the industrial material handling industry since 1981, bringing over 45 years of hands-on experience helping businesses select the right equipment for their applications. His expertise includes specifying and quoting Buckhorn and Monoflo collapsible bulk containers, Davco sheet metal and wire bins, and bulk container dollies.

Questions about this guide? Call 866-333-0728 to speak with an experienced material handling specialist.

Ready for a quote?

Send us these details and a material handling specialist will reply, typically within one business day.

  • Dimensions
    Size of the load and the space it goes in
  • Load
    Weight per item, shelf or level
  • Quantity
    How many units you need
  • Delivery ZIP code
    For freight pricing
  • Drawing
    A sketch, photo or spec sheet, if you have one
Get a Fast Quote Call 866-333-0728

Tell us the pallet, the product and the loop

Give us your footprint, your product density, and how many empties move in a month. We will size the fleet and run the freight math with you. Quotes are reviewed by material handling specialists, typically within one business day.

866-333-0728

Browse bulk containers at custommhs.com

No bots. No guesswork. Real experts.

Sources

Buckhorn, Monoflo, Davco, Triple Diamond, Orbis, Worldwide Material Handling, Vestil and Little Giant figures as published on CustomMHS product listings.

Disclaimer. This guide is educational content and reflects the opinion and general experience of CustomMHS. Published figures are subject to change by the manufacturer. Stacking practice and rack loading should follow your facility's written safe work procedures and the manufacturer's published limits for your exact models. Confirm critical specifications against the current data sheet before ordering. Reviewed November 2026.