Industrial Equipment Experts Since 1980 | Mon–Fri, 7 AM–6 PM ET
No bots. Real experts. 866-333-0728
Get a Fast Quote
Get a Fast Quote

CustomMHS Buyer's Guide

Reel Lifts & Rotators

Sixteen Logitrans rotators sit in this category, and several differ by a single letter. This guide decodes the names, sizes the machine to the reel, and explains which units bring OSHA operator training with them.

Covers: Logitrans reel rotators · box holder rotators · RL-500 reel lifter Questions: 866-333-0728 Written and reviewed by: Tom McGovern · November 2026
Section One

Two families in one category

The category is called reel lifts and rotators, but half of what is in it never touches a reel.

Quick answers
  • Logitrans reel rotators are published at 1,100 lb, 69 in of lift, and reel diameters from 4.7 in to 50 in. A 54 in reel does not fit any model.
  • Box holder rotators are a different machine: 2,200 lb, five lift heights from 36 in to 75 in, for boxes and crates, not reels.
  • The model letters describe the machine. E is electric lift, S after F is straddle legs, RR is a reel rotator, M is manual rotation, and a leading S is powered drive.
  • A 48 in reel with 1,000 ft of 500 kcmil copper weighs roughly 1,800 lb, well over 1,100 lb. Weigh your heaviest reel before you order.
  • Any model with an electric motor falls under OSHA 1910.178, so the operators need training and evaluation.

Everything in this category is made by Logitrans, a Danish maker of walk-behind lifting equipment. The machines tilt, rotate and reposition boxes, crates, and wire or cable reels, from fully manual to fully powered lift, push, rotation and clamping.

Family one

Reel rotators, 1,100 lb

Two gripping arms with rubber-covered pads close on the flanges of a reel, lift it, and tilt it in 90 degree steps. Eight models. Published: 1,100 lb capacity, 69 in lifting height, reel diameters from 4.7 in to 50 in, and arms that open to 51 in.

Family two

Box holder rotators, 2,200 lb

A holder supports a box, crate or tote and tilts it beyond 90 degrees so a person can reach in or empty it. Eight models. Published: 2,200 lb capacity, lifting heights of 36, 47, 55, 63 and 75 in, and forks 22 in or 27 in wide by 49 in long.

A seventeenth product, the RL-500 reel lifter, belongs to neither family. It lifts reels and does not rotate them, and it costs far less than a rotator. Section seven covers it, because for many buyers it is the right answer.

What this guide does not give you

Overall dimensions, unit weights, battery specifications and turning radius are not on the listings, so they are not here. Section fourteen lists what to ask for in writing before you order.

Please read this part

This guide is educational and reflects the opinion and general experience of CustomMHS as an equipment distributor. It is not an engineering or compliance assessment. Every Logitrans figure here is taken from the CustomMHS listings. OSHA rules are summarized, and the standards govern in full. Confirm the current data sheet for your exact model before you order.

Section Two

Decoding the model number

Every letter is a function. Read left to right and the machine describes itself.

Short answer: E is electric lift, F is fork over, S after F is straddle legs, RR is a reel rotator, a final M is manual rotation, a final A is an adjustable box holder, and a leading S is powered drive.

The listings state which functions are manual and which are electric on each model. Match the letters to those functions across all sixteen rotators and the scheme reads the same way every time.

The Logitrans letter scheme, as it reads across the sixteen rotators
Letter Meaning
S, first letter Powered travel drive. The machine drives and the operator walks with it
E Electric lift
L Lift
F Fork over chassis
S, after F Straddle legs
R Rotator
RR Reel rotator. A single R is a box holder rotator
M, last letter Manual rotation. No M means electric rotation
A, last letter Adjustable box holder, 31.5 in to 48 in

Worked example. ELFSRRM 1001 reads Electric lift, Lift, Fork over, Straddle legs, Rotator, Reel, Manual rotation. That is an electric-lift, hand-pushed, hand-rotated straddle-leg reel rotator, which is what the listing describes.

The series numbers

Each model ends in 1001 or 1003. On the listings, every model with powered travel drive is 1003 and every model the operator pushes is 1001. Two models add the word Maxi, the SELFRR Maxi 1003 and the SELFSRRE Maxi 1003. They are the top of each reel line, powered on all four functions.

Read the model on your quote letter by letter

Several of these names differ by one letter. ELFRR and ELFSRR are different machines, and so are ELFR and ELFRR. Check the full model string on the quote against the functions you agreed to.

Section Three

The four functions, and which to power

Lift, push, rotation and clamping. Each one is manual or powered.

Short answer: Power the lift first, rotation second if you turn reels more than a few times an hour, and the drive last, only when travel is long.

What each function means
Function Manual Powered
Lift The operator pumps the load up by hand A battery-powered lift
Push The operator pushes the machine A drive motor moves it and the operator walks along. This is the leading S and the 1003 series
Rotation The operator turns the load. Reel rotators lock every 90 degrees Powered rotation. On reel rotators it works only above the height in section ten
Clamping Arms or holder set by hand Electric clamping of the reel flanges
The four fork over reel rotators as a ladder
Model Lift Push Rotation Clamping
LFRRM 1001 Manual Manual Manual Manual
ELFRRM 1001 Electric Manual Manual Confirm on the quote
ELFRR 1001 Electric Manual Electric Electric
SELFRR Maxi 1003 Electric Electric Electric Electric

All four handle the same reel and lift it to the same height. Electric lift is the smallest step up. Electric rotation is a larger step. Powered drive is the largest step by far. The reel rotator listings also publish a lower unit price for three or more machines, so ask for the quantity price if you are buying several.

An honest ranking

Power the lift first, always. Power the rotation second if operators turn reels more than a few times an hour, because turning a loaded reel by hand is the hardest of the four jobs to repeat. Power the drive last. Buying powered drive to save thirty feet of pushing spends the biggest step on the smallest problem.

Section Four

Fork over or straddle legs

This is a pallet question with a right answer, not a preference.

Short answer: Fork over needs an open-entry pallet or skid. Straddle legs pass outside the load and work with any pallet, including solid-deck pallets and closed-bottom containers.

Fork over

The forks pass over the pallet deck

Works with standard four-way pallets, open-bottom pallets and skids. Narrower, and the less expensive of each pair. It does not handle solid-deck pallets or closed-bottom containers.

Straddle legs

The legs run down each side of the load

The legs pass outside the pallet or reel, so the pallet type stops mattering. The stance is wider. On the reel rotators, the leg width is an option you choose at order.

Matched pairs: the same machine in each chassis
Machine Fork over Straddle
Reel, all manual LFRRM 1001 LFSRRM 1001
Reel, electric lift ELFRRM 1001 ELFSRRM 1001
Reel, electric rotation ELFRR 1001 ELFSRR 1001
Reel, fully powered SELFRR Maxi 1003 SELFSRRE Maxi 1003
Box, adjustable, electric lift ELFRA 1001 ELFSRA 1001
Box, fixed, electric lift ELFR 1001 ELFSR 1001
Box, adjustable, powered drive SELFRA 1003 SELFSRA 1003
Box, fixed, powered drive SELFR 1003 SELFSR 1003

On the reel rotators the straddle version costs only a little more than the fork over version, so if there is any doubt about what your reels sit on, straddle is cheap insurance. On the box holder rotators the difference is larger. Have both quoted and compare.

Section Five

The reel rotators

Eight machines, one chassis family, four functions switched on in order.

Short answer: All eight publish 1,100 lb, 69 in of lift and reels from 4.7 in to 50 in. Choose by chassis and by how many functions are powered.

Published on the reel rotator listings
Specification Published value
Capacity 1,100 lb
Lifting height 69 in
Reel diameter 4.7 in to 50 in
Gripping arm opening 51 in
Gripping pads Rubber covered, for soft and hard reels
Tilt, manual rotation models Set every 90 degrees, with a locking system
Release interlock The arms cannot be opened by mistake. A reel can only be released on the floor or a pallet
The eight reel rotators
Model Chassis Lift Push Rotation
LFRRM 1001 Fork over Manual Manual Manual
ELFRRM 1001 Fork over Electric Manual Manual
ELFRR 1001 Fork over Electric Manual Electric
SELFRR Maxi 1003 Fork over Electric Electric Electric
LFSRRM 1001 Straddle Manual Manual Manual
ELFSRRM 1001 Straddle Electric Manual Manual
ELFSRR 1001 Straddle Electric Manual Electric
SELFSRRE Maxi 1003 Straddle Electric Electric Electric
  • Clamping: the two all-manual models clamp by hand. The electric-lift models are listed with electric clamping. Confirm the clamping type for the exact model on your quote.
  • Controls: the listings describe a touch screen controller that can be programmed for stops, turning angle, speed and rotation. Confirm what the model you are quoting ships with.
  • Two lifting speeds: the LFSRRM 1001 publishes normal and quick lifting speeds and steering on both wheels.
Section Six

The box holder rotators

Twice the capacity, five lift heights, and one question that decides the model: does the box size vary?

Short answer: Choose an adjustable holder for boxes of different widths and a fixed holder for one standard box. Tilting works only when the rotation center is between 27 in and 46.5 in above the floor.

Published on the box holder rotator listings
Specification Published value
Capacity 2,200 lb
Lifting heights 36, 47, 55, 63 and 75 in
Fork size 22 in or 27 in wide by 49 in long, chosen at order
Tilt Beyond 90 degrees
Adjustable holder range 31.5 in to 48 in, on the four A models, set with one tool-free handle
Clamps Holders with clamps are recommended when tilting more than 60 degrees

Adjustable or fixed

The adjustable models cover box widths from 31.5 in to 48 in. The fixed models, ELFR 1001 and ELFSR 1001, are ordered in one holder width, and the widths offered depend on the fork size.

Fixed box holder widths as listed
Fork width ordered Holder widths offered
22 in 31.5 in, 33.5 in, 37.8 in or 39.4 in
27 in 39.4 in, 41.3 in, 45.7 in or 47.2 in

Record both the fork width and the holder width on the purchase order. A fixed holder cannot be changed later. A box narrower than 31.5 in or wider than 48 in is outside both ranges.

The tilting window is 27 in to 46.5 in

The model pages publish that tilting is switched off when the rotation center is more than 46.5 in or less than 27 in above the floor. On a machine ordered with 63 in or 75 in of lift, most of that height is lift, not tilt. If the job is tilting and not stacking, the tallest model does not buy a bigger tilting window.

All eight are electric lift. The four that begin with S add powered drive: SELFR, SELFSR, SELFRA and SELFSRA 1003. On the straddle models, confirm the straddle leg width at order. The box holder models are listed with a cabled remote control for rotation, lifting and lowering, with wireless as an option.

Section Seven

The RL-500, and when it is enough

A fraction of the price of a rotator, and for some shops it does the whole job.

Short answer: If you only need to lift a reel and place it on a shaft or spindle, the RL-500 does it. If the reel has to be turned, you need a rotator.

What it does

Lifts a reel. Does not rotate it.

Published at 1,100 lb, reel diameter up to 50 in and reel length up to 20.5 in. Manual lift and manual drive, a flow valve for controlled lowering, adjustable forks, and a foot brake. The listing positions it for loading reels onto production machines.

What you give up

Rotation and power

It cannot lay a reel over or index it, nothing on it is powered, and the 20.5 in reel length is a hard limit.

The question that decides it

Do you need the reel turned, or just lifted and placed? Loading a payoff shaft or a machine spindle is lifting and placing. Laying a reel from standing to flat, or turning it to reach the lead end, is rotation. Measure your reels across the flange faces and confirm with us what the 20.5 in figure covers before you decide the RL-500 fits.

Section Eight

Will your reel fit

Three dimensions decide it, and the listings publish two of them.

Short answer: The limit is a 50 in flange. A 48 in reel fits with 2 in to spare. A 54 in reel does not fit any model.

The reel rotators publish a diameter range of 4.7 in to 50 in and arms that open to 51 in. Reel width is not published for the rotators, and no option extends the diameter range.

Standard reel sizes against the 50 in limit. Reel dimensions from the Encore Wire reel chart
Flange diameter Traverse Within the 50 in limit?
12 to 18 in 4.9 to 14 in Yes
24 in 12 to 16 in Yes
30 to 36 in 18 to 22 in Yes
42 in 23 in Yes
48 in 23 in Yes, with 2 in to spare
54 to 60 in 32 in No
72 to 78 in 36 to 48 in No
The line falls between 48 in and 54 in

If any part of your mix runs to 54 in, 60 in or 72 in flanges, these machines will not take those reels. Settle that before you compare models.

The three things to measure

  • Flange diameter of your largest reel, not your typical one.
  • Overall width, flange face to flange face. Ask us to confirm the limit in writing, because it is not on the listings.
  • Loaded weight of your heaviest reel, on a scale.
Section Nine

What a loaded reel weighs

The 1,100 lb rating sounds generous until you weigh what is on the reel.

Short answer: Add the empty reel to the cable. A 48 in wood reel is about 178 lb empty, and 1,000 ft of 500 kcmil copper is about 1,600 lb more.

Empty wood reel weights, from the Prysmian wood reel chart
Flange Traverse Empty weight
29.5 in plywood 18 in 40 lb
38 in 27 in 90 lb
48 in 22 in 178 lb
59 in 40 in 300 lb
72 in 36 in 616 lb

Worked example: 1,000 ft of 500 kcmil copper THHN on a 48 in wood reel

Reel weight
Item Weight Source
Conductor, 1,000 ft About 1,600 to 1,660 lb Cerrowire publishes 1,599 lb and Southwire about 1,662 lb per 1,000 ft
Empty 48 in reel 178 lb Prysmian wood reel chart
Total About 1,780 to 1,840 lb Our arithmetic
Machine rating 1,100 lb Logitrans reel rotators

That ordinary reel is 60 to 70 percent over the rating. A 48 in reel of lighter cable is not. The flange diameter tells you whether the reel fits. It tells you nothing about the weight. Both tests have to pass.

Weigh the heaviest reel you handle

Get a scale weight for your worst case before you order. OSHA 1910.178(o)(2) allows only loads within the rated capacity of the truck. Published reel capacity figures are typical values, and the wire and cable packaging standard ANSI/NEMA WC 26 says to use them as a guide only.

Why not lift reels by hand

The NIOSH Revised Lifting Equation starts from a load constant of 51 lb under ideal conditions and reduces it for every way the lift is less than ideal. A reel is picked up from the floor, cannot be held close to the body, has no handles, and is set down with a twist. The recommended limit for a reel is a fraction of 51 lb, against reels that weigh hundreds or thousands.

Section Ten

The 32.5 in rotation height

A published operating limit that changes how you lay out the work.

Short answer: On models with electric rotation, the reel must be raised above 32.5 in before it will rotate. Manual rotation models have no published height limit.

The limit applies to the ELFRR 1001, ELFSRR 1001, SELFRR Maxi 1003 and SELFSRRE Maxi 1003.

Worked example: overhead clearance

Rotating a 48 in reel
Step Math Result
Lowest rotation height 32.5 in
Half the flange diameter 48 in ÷ 2 24 in
Top of the flange while rotating 32.5 in + 24 in 56.5 in, or 4 ft 8-1/2 in
Add The gripping arms and working room Confirm with us
  • You cannot rotate a reel near the floor on these four models.
  • Measure your lowest obstruction: sprinkler heads, door headers, mezzanines and conveyors.
  • If the reel goes onto a payoff or spindle, the spindle height and the rotation height together set your working range.

Design your layout to 32.5 in and have the figure confirmed in writing for the machine on your quote. The manual rotation models, ELFRRM and ELFSRRM, carry no published height limit. If you need to turn reels at low height, the less expensive machine may be the more capable one for that job.

Section Eleven

Straddle leg widths

Four leg widths are listed on the straddle reel rotators.

Short answer: Pick the leg width to clear your widest pallet or reel stand. Options A, B and C carry no added cost. Confirm the rated capacity in writing before choosing option D.

Straddle leg width options as listed on LFSRRM, ELFSRRM and ELFSRR
Option Inside width Cost
A 33 in to 37 in No added cost
B 37 in to 44 in No added cost
C 44 in to 51 in No added cost
D 49 in to 56 in Priced option

Choose the width against the widest pallet, base or reel stand the legs have to pass, and against your narrowest aisle. A wider stance needs more room to turn. A 48 in wide pallet falls in option C.

Option D changes the rating

The widest setting is listed with a change in lifting capacity. Do not order option D on an assumption. Get the rated capacity for the exact model and leg width in writing on the quote. For the fully powered straddle model, ask us which leg widths are available.

Section Twelve

OSHA: which of these needs a trained operator

The line runs between powered and not powered, and it does not run where most buyers assume.

Short answer: The RL-500 and the two all-manual rotators have no motor and fall outside 1910.178. The other fourteen models have an electric motor, and the operator training rule applies.

The scope of 29 CFR 1910.178(a)(1) covers fork trucks, tractors, platform lift trucks, motorized hand trucks and other specialized industrial trucks powered by electric motors or internal combustion engines. Walk-behind equipment is inside it. OSHA restated the test in a Letter of Interpretation dated September 19, 2023: equipment powered by electric motors and designed to carry, push or pull material is subject to 1910.178, and the design of the vehicle is what decides it, not how it is used.

Where each model sits
Models Powered functions 1910.178 Operator obligation
RL-500, LFRRM 1001, LFSRRM 1001 None Outside No 1910.178(l) training obligation. 1910.176 and the General Duty Clause still apply
The other fourteen models Electric lift, and on most, electric clamping, rotation or drive Inside Training, workplace evaluation, employer certification, re-evaluation at least every three years
Electric lift alone is enough

Moving from the all-manual LFRRM to the electric-lift ELFRRM puts an electric motor on the machine. It does not have to drive itself. That is not a reason to avoid the electric models. It is a reason to budget for training before the machine arrives.

What 1910.178(l) requires

  • (l)(1)(ii): training is completed before the employee operates the truck, except during training.
  • (l)(2)(ii): formal instruction, practical training, and an evaluation in the workplace. All three.
  • (l)(4)(iii): an evaluation of each operator at least once every three years.
  • (l)(6): the employer certifies each operator, with the operator's name, the training date, the evaluation date and who did the training or evaluation. There is no OSHA-issued license.

Rules that read directly onto reel work

  • 1910.178(o)(1): only stable or safely arranged loads are handled, with caution for off-center loads.
  • 1910.178(n)(4): if the load blocks the forward view, travel with the load trailing. A large reel does that.
  • 1910.178(q)(7): trucks are examined before being placed in service, at least daily.
  • 1910.178(m)(5): an unattended truck has its load lowered, controls neutral, power off and brakes set. Unattended means the operator is 25 ft or more away or cannot see the truck.
CE marking is not a US compliance credential

Logitrans is a European manufacturer. CE marking has no legal force in the United States and does not satisfy an OSHA requirement. A powered unit sold here still falls under 1910.178, including its design requirement in (a)(2), and its operators still need 1910.178(l) training.

Section Thirteen

Storing reels once they are off the machine

A reel handler solves the lifting problem. It does not solve the rolling problem.

Short answer: Chock or rack every reel standing on its flanges, and buy the chocks or racks with the reel handler.

A reel standing on its flanges can roll the moment it is set down. The federal rule that names cable reels is in the telecommunications standard, 29 CFR 1910.268(k)(2): cable reels in storage are to be checked or otherwise restrained when they might accidentally roll from position. That standard applies to telecommunications work, so for a warehouse or an electrical contractor it is the closest express rule and is best read alongside the general ones:

  • 1910.176(b): storage of material shall not create a hazard, and stored material is to be stable and secure against sliding or collapse.
  • 1910.176(a): where mechanical handling equipment is used, there must be safe clearances in aisles, at docks and through doorways, and aisles are kept clear. Read this before you choose a straddle width.

The rotators have an interlock so a reel can only be released on the floor or a pallet. That protects the release, not what happens next.

If you were considering a sling and a crane

1910.184(d) requires slings and their fastenings to be inspected each day before use by a competent person. That is a daily duty a manual reel lifter does not carry.

Section Fourteen

What to ask for in writing

The listings publish capacity, lift height, reel diameter, holder widths and a price on every model. These items are not on them.

Short answer: Before you order, get the overall size, turning radius, lowered height, unit weight, battery and charger details, reel width limit, warranty term and lead time in writing.

Request each of these with your quote
Item Why it matters
Overall length, width and height Door widths, aisles and truck loading
Turning radius Whether the machine works in your aisle
Lowered height What it can pass under
Unit weight Floor and mezzanine loading, and freight
Battery voltage, capacity and charger Charging setup is a real cost
Run time and charge time Whether one machine covers a shift
Reel width limit, flange face to flange face Not on the rotator listings
Rated capacity for the exact configuration Especially with the widest straddle legs
Warranty term In months or years
Lead time These are built in Denmark
Freight Quoted separately
Turn this table into your request

Send us the list with the model you want. The answers become the record you check the delivered machine against.

Section Fifteen

A worked selection

One shop, three budgets, three defensible answers.

Short answer: For 12 to 15 reels a day up to 48 in and 980 lb on mixed pallets, a straddle-leg, electric-lift, manual-rotation model is the balanced choice.

An electrical contractor's shop receives cable on wood reels, stages them, and loads them onto a payoff cart. Flanges run from 24 in to 48 in. The heaviest reel is 980 lb on the scale. Reels arrive on the floor and on pallets, some open and some solid deck. Twelve to fifteen reels a day, with travel under 60 ft.

  1. Does the reel fit? The largest flange is 48 in, inside the 50 in limit by 2 in. The heaviest reel is 980 lb, inside 1,100 lb by 120 lb. Both pass, but a heavier cable would not.
  2. Fork over or straddle? Some pallets are solid deck, so straddle legs.
  3. Straddle width? The widest pallet is 48 in, which is option C at 44 in to 51 in.
  4. Which functions to power? Travel is short, so powered drive is hard to justify. Reels are laid over on every cycle, so rotation is used every time.
Three defensible answers
Choice Model The case for it
Lean LFSRRM 1001, option C All manual and the least expensive machine that does the job. Outside 1910.178. Pumping 15 reels a day by hand is real work but reasonable
Balanced ELFSRRM 1001, option C Electric lift for one modest step up. Rotation stays manual, so there is no 32.5 in rotation height to design around. Operator training applies
Heavier duty ELFSRR 1001, option C Adds electric rotation. Worth it at higher cycle counts. Brings the 32.5 in rotation height into the layout

The balanced choice removes the hardest repeated task, the lifting, for the smallest step. Budget beyond the machine for operator training, freight, charging, and reel chocks or a rack. If this shop only lifted reels onto a shaft and never laid one over, the RL-500 would do it, provided the reels are within its 20.5 in reel length.

Section Sixteen

Common and costly mistakes

In rough order of what they cost.

Short answer: Weigh the reel, check the flange against 50 in, match the chassis to your pallets, and plan for operator training on any electric model.

Sizing by the reel instead of the load

A 48 in reel fits. A 48 in reel of 500 kcmil copper weighs about 1,800 lb.

Not knowing electric lift brings operator training

Any model with an electric motor is inside 1910.178.

Buying fork over when the pallets are solid deck

Fork over needs open-entry pallets.

Assuming reels over 50 in are covered

They are not, on any model.

Planning to rotate near the floor

Electric rotation works only above 32.5 in of lift.

Buying powered drive for short travel

It is the largest step in the category.

Ordering a fixed box holder without recording fork width and holder width

Neither can be changed later.

Skipping reel restraint

What happens after the reel is released is a storage question.

Section Seventeen

Frequently asked questions

The questions buyers ask before ordering.

What do the letters in the Logitrans model numbers mean?

A leading S is powered travel drive, E is electric lift, L is lift, F is fork over, an S after the F is straddle legs, R is rotator, RR is a reel rotator, a final M is manual rotation and a final A is an adjustable box holder.

What is the difference between 1001 and 1003?

On the listings, every model the operator pushes is series 1001 and every model with powered travel drive is series 1003.

How big a reel will these handle?

The reel rotators publish reel diameters from 4.7 in to 50 in and a capacity of 1,100 lb. A 48 in reel fits. A 54 in reel does not fit any model.

Do operators need training to use one of these?

For any model with an electric motor, yes. OSHA 1910.178 covers motorized hand trucks powered by electric motors, and 1910.178(l) requires training, a workplace evaluation and employer certification. The RL-500 and the two all-manual rotators have no motor and are outside that rule.

Why can I not rotate the reel near the floor?

On models with electric rotation, the listings publish that rotation is only possible at lifting heights above 32.5 in. Models with manual rotation have no published height limit.

Should I choose fork over or straddle legs?

Fork over needs open-entry pallets or skids. Straddle legs pass outside the load and work with any pallet, including solid-deck pallets and closed-bottom containers.

What does a loaded cable reel weigh?

Add the empty reel to the cable. A 48 in wood reel is about 178 lb empty, and 1,000 ft of 500 kcmil copper is about 1,600 to 1,660 lb, for a total near 1,800 lb.

Which functions should I pay to power?

Power the lift first. Power the rotation second if operators turn reels more than a few times an hour. Power the drive last, and only if travel distances are long.

Is the RL-500 a cheaper version of the reel rotators?

No. It lifts a reel and places it but does not rotate it. It is published at 1,100 lb, reels up to 50 in in diameter and up to 20.5 in in reel length.

What is the difference between box holder rotators and reel rotators?

Reel rotators grip a reel by its flanges and are rated at 1,100 lb. Box holder rotators support and tilt a box, crate or tote and are rated at 2,200 lb. They do not handle reels.

Do I still need to chock reels after buying a handler?

Yes. A reel standing on its flanges can roll once it is set down. Chock or rack every stored reel.

Section Eighteen

Quick-reference tables

The things worth having on one screen.

The decoder
Letter Means
S, first letter Powered travel drive. The machine drives and the operator walks with it
E Electric lift
L Lift
F Fork over chassis
S, after F Straddle legs
R Rotator
RR Reel rotator. A single R is a box holder rotator
M, last letter Manual rotation. No M means electric rotation
A, last letter Adjustable box holder, 31.5 in to 48 in
Published figures
Reel rotators Box holder rotators RL-500
Capacity 1,100 lb 2,200 lb 1,100 lb
Lift height 69 in 36, 47, 55, 63 or 75 in See listing
Reel diameter 4.7 in to 50 in Not applicable Up to 50 in
Reel length Ask us Not applicable Up to 20.5 in
Holder range Not applicable 31.5 in to 48 in on A models Not applicable
Rotation Every 90 degrees on manual models Beyond 90 degrees None

Specify-it checklist

  • Largest reel flange diameter, against 50 in.
  • Heaviest loaded reel, weighed, against 1,100 lb.
  • Widest reel, flange face to flange face.
  • What the reels sit on. Any solid-deck pallet means straddle legs.
  • Widest thing the straddle legs must pass.
  • Cycles per day and travel distance.
  • Lowest overhead obstruction where reels are rotated.
Before you order

Confirm the full model string, the chassis, the leg width, the powered functions and the rated capacity on the quote.

About the author. Tom McGovern has worked in the industrial material handling industry since 1981, bringing over 45 years of hands-on experience helping businesses select the right equipment for their applications. His expertise includes specifying and quoting Logitrans reel rotators, box holder rotators and the RL-500 reel lifter.

Questions about this guide? Call 866-333-0728 to speak with an experienced material handling specialist.

Ready for a quote?

Send us these details and a material handling specialist will reply, typically within one business day.

  • Dimensions
    Size of the load and the space it goes in
  • Load
    Weight per item, shelf or level
  • Quantity
    How many units you need
  • Delivery ZIP code
    For freight pricing
  • Drawing
    A sketch, photo or spec sheet, if you have one
Get a Fast Quote Call 866-333-0728

Tell us the reel, the weight and what it sits on

Largest flange, heaviest loaded reel on a scale, and the pallets or floor the reels arrive on. Those three answers pick the machine. Quotes are reviewed by material handling specialists, typically within one business day.

866-333-0728

Browse reel lifts and rotators at custommhs.com

No bots. No guesswork. Real experts.

Sources

29 CFR 1910.178, 1910.176, 1910.184 and 1910.268(k)(2) · OSHA Letter of Interpretation, September 19, 2023 · NIOSH Revised Lifting Equation · ANSI/NEMA WC 26 · Encore Wire and Prysmian reel charts · Southwire and Cerrowire conductor data · Logitrans figures as published on CustomMHS product listings.

Disclaimer. This guide is educational content and reflects the opinion and general experience of CustomMHS. It is not an engineering or compliance assessment. Every Logitrans figure is taken from the CustomMHS listings and should be confirmed on your quote. OSHA rules are summarized, and the standards govern in full. Reviewed November 2026.