Industrial Equipment Experts Since 1980 | Mon–Fri, 7 AM–6 PM ET
No bots. Real experts. 866-333-0728
Get a Fast Quote
Get a Fast Quote

CustomMHS Buyer's Guide

Small Parts Bins: Stack and Hang, Shelf & Fiberglass Bins

How the bin types differ, which one belongs in your operation, and the details that decide whether a bin lasts five years or five months.

Covers: Akro-Mils · Quantum · LEWISBins · Kadon · MFG Questions: 866-333-0728 Written and reviewed by: Tom McGovern · November 2026
Section One

Why the bin choice matters more than it looks

A bin is a low-cost item that quietly controls a high-cost activity: how fast your people find and pick parts.

Quick answers
  • A hopper front is the fastest bin front to pick from, because you reach in without moving the bin. Stack and hang bins and shelf bins both have one.
  • Stack and hang bins add a rear tab that hangs on a louvered panel or rail. Shelf bins are long and low, sized to sit in rows on 12, 18 or 24 in deep shelving.
  • Polypropylene is the default material. Fiberglass composite is for hot parts, wash lines and harsh chemicals. ESD bins are for bare electronics.
  • Published load ratings in this category run up to 150 lb per bin. Check the rating for the exact model before you load it.
  • Measure shelf depth before you order. A 14-3/4 in long bin leaves 3-1/4 in unused at the back of an 18 in deep shelf. The 20-1/2 in long 1800-series is designed for 18 in deep shelving.

Storage bins look interchangeable on a catalog page. In practice, the wrong bin creates the same three problems over and over: operators dig through containers to find the part they want, bins crack or bow under weight and get replaced, and stock runs out because nobody could see the bin was empty.

Every feature in this guide traces back to one of those three failure points:

Access

Can you reach the part without moving the bin?

This is what the hopper front is for. You get it on stack and hang bins and on shelf bins. It is the feature most buyers overlook.

Durability

Will it survive the load and the environment?

Material and wall construction decide this. A polypropylene bin in a heat-treat area is a replacement order waiting to happen.

Visibility

Can you tell what is inside and how much is left?

Clear bodies, label slots, indicator bins and wire mesh all exist to answer this without an operator walking over.

How to use this guide

If you already know your bin style, jump to materials or the spec table. If you are starting from scratch, read sections two through five in order, then use the application chart to confirm.

Please read this part

This guide is educational and reflects the opinion and general experience of CustomMHS as an equipment distributor. Sizes, load ratings and temperature limits are the manufacturers' published figures and can change. Confirm the current data sheet for your exact model before you order.

Section Two

The four bin styles, and what each one is for

Nearly every product in this category is a variation on four basic shapes. Understand these and the catalog stops being confusing.

Short answer: Stack and hang bins and shelf bins both have a hopper front. Stack and hang bins go on panels, rails and benches, shelf bins go in rows on shelving, drawer bins hold many small part numbers, and wire mesh bins suit wet or oily parts.

A hopper front is a feature, not a bin style

A hopper front is a front wall cut down so you can see the parts and reach them while the bin stays where it is. Stack and hang bins have one. Shelf bins have one too. What separates those two styles is the shape of the bin and what it sits or hangs on.

1. Stack and hang bins (the classic hopper front bin)

The defining feature is a cut-away front wall with a curved or angled lower lip. Your hand goes in from the front and the contents slide toward you. You never lift, tilt or pull the bin off the shelf to get a part.

On a shelf loaded several bins deep and high, getting a part from an enclosed tote means pulling the tote out, setting it down, digging, and putting it back. A hopper front turns that into a single reach. Multiply by a few hundred picks a shift and the difference is real labor.

The other half of the design is the rear hanging tab. A molded hook on the back wall drops onto a louvered panel, a steel rail, a bench rack or a cart. The same bin works three ways: sitting on a shelf, stacked on another bin, or hanging on a wall.

Best for: fasteners, fittings, electrical components, connectors, seals, and any part picked repeatedly through the day. See Akro-Mils 30-Series hopper front bins, Quantum Ultra Stack and Hang bins and LEWISBins PB-Series bins.

2. Shelf bins (hopper front bins made for shelving)

A shelf bin also has a hopper front. The front wall is cut down so you can read the label, see the fill level and pick the part while the bin sits on the shelf. What makes it a shelf bin is the shape: long, narrow and low, made to run the depth of a shelf and sit side by side in rows.

The lengths are matched to shelving. Akro-Mils 4 in shelf bins and LEWISBins 4 in shelf bins come in 11-5/8 in, 17-7/8 in and 23-5/8 in lengths for 12 in, 18 in and 24 in deep shelves, in widths from 2-3/4 in to 11-1/8 in. The Akro-Mils ShelfMax is the 6 in high version. Akro-Mils states it holds up to 85% more than a traditional 4 in bin, with a front opening 3/4 in higher than comparable 6 in bins. LEWISBins publishes that its raised hopper front stores up to 35% more than a standard shelf bin.

Shelf bins take dividers, so one bin can hold several part numbers. The Akro-Mils 4 in bins accept up to seven dividers on every model except the narrowest, and LEWISBins lists both width and length dividers. The Akro-Mils and LEWISBins bins nest when empty. The Akro-Mils bins also have a built-in rear hanglock that lets the bin tilt out for full access.

Quantum stackable shelf bins are a heavier take on the same idea: ten sizes, all 7 in high, with a raised front opening, optional cross dividers, an FDA-approved material and a published autoclave limit of 250°F.

Best for: stockrooms, order picking shelving, maintenance parts, and any run of shelving that holds many part numbers in rows. Choose a stack and hang bin instead when the bin has to hang on a panel or rail, or stack on a bench.

3. Drawer bins

Individual plastic drawers running in a frame. Each drawer pulls out, is typically divisible into compartments, and closes to keep contents clean.

Drawer bins win on density: many separate part numbers fit in a small footprint. They lose on speed, since every retrieval means opening a drawer.

Best for: electronics assembly, tooling, small hardware with many part numbers, and maintenance benches. See Akro-Mils heavy duty storage drawers and Quantum Super Tuff Euro drawer bins.

4. Wire mesh bins and baskets

Open steel wire rather than solid walls. Contents are visible from every angle and air passes straight through.

There are two reasons to choose them. The first is ventilation, which matters for parts that come off a wash line wet or carry cutting oil. The second is instant inventory checks, since a supervisor can read the fill level of a whole rack from the aisle.

Best for: post-wash staging, oily or damp parts, and anywhere chips and debris would collect in a solid bin. See Quantum wire mesh bins.

Bin style at a glance
Style Hopper front Hangs on a panel or rail Dust protection Pick speed Typical home
Stack and hang bin Yes Yes Low Fastest Line-side, workbench, wall panel
Shelf bin Yes No, sits on shelving Low Fast Shelving 12, 18 or 24 in deep
Drawer bin No No, runs in a frame Best Slower Bench, tool crib, electronics
Wire mesh Varies Varies None Fast Wash lines, damp or oily parts
Section Three

Materials: where most of the money and most of the failures live

Style determines how fast you pick. Material determines whether the bin is still in service in three years.

Short answer: Buy polypropylene unless heat, harsh chemicals or static rule it out. Fiberglass composite handles heat and chemicals, ESD bins protect electronics, and wire mesh drains and ventilates.

Polypropylene: the industrial default

Most small parts bins are injection-molded polypropylene, and for most facilities it is the right answer. It is waterproof, will not rust, comes in colors for sorting, and takes a molded label slot cleanly.

Higher-grade lines use ribbed, reinforced walls and, in the largest sizes, double wall thickness. That is what keeps a loaded bin from bowing outward and losing its stack. When two polypropylene bins sit at different prices, the ribbing and wall section is usually where the difference is.

Temperature is the real limit. Quantum publishes its Ultra Stack and Hang bins as autoclavable up to 250°F and resistant to extreme cold, and gives a range of -40°F to 250°F for its Magnum line. That covers cold storage and steam sterilization. It does not cover a part that just came out of a furnace.

Fiberglass composite: for heat, chemicals and abuse

MFG glass-reinforced composite containers exist for the conditions polypropylene cannot handle. MFG publishes continuous use from -60°F to 250°F and intermittent use up to 300°F, and states that, unlike many thermoplastic units, they will not melt when in contact with most hot objects.

Chemical resistance is broader too. MFG lists cutting oils, greases, radiation, and mild acids and alkaline solutions within a pH of 3.0 to 10.0.

Fiberglass costs more up front. It earns that back in heat treat, foundry work, machining with hot chips, paint and coating lines, parts washers, and anywhere a plastic bin is being replaced on a schedule. See MFG fiberglass hopper bins.

The deciding question

Will anything that goes into this bin ever be hot, or will the bin sit near a heat source, a wash line or aggressive chemicals? If yes, price the fiberglass. If no, polypropylene is almost certainly the better value.

ESD bins: for electronics

Standard polypropylene is an insulator and can build and hold a static charge, which can damage electronic components.

ESD bins are molded from a static-dissipative material that bleeds charge away. Akro-Mils publishes a static dissipative range of 104 to 1011 ohms per square for its ESD bins and states the material has a very low carbon content and will not leave black residue on parts. These bins are black, which keeps them visibly distinct from standard stock.

If you build, repair or handle bare electronic assemblies, this is not an upgrade. It is the correct part. See Akro-Mils conductive bins and Quantum conductive hopper front bins.

Clear bins: for pick speed

A clear body lets an operator confirm contents and fill level without reading a label or reaching in. Where similar parts sit side by side, that removes a whole class of pick errors. Some solid-color bins take an optional clear window, which gives you the color-coding of an opaque bin with a viewing port. See Quantum heavy duty clear bins.

Material comparison with published figures
Material Published temperature Published chemical resistance Relative cost Choose it when
Polypropylene Quantum Ultra: autoclavable up to 250°F. Quantum Magnum: -40°F to 250°F Waterproof, will not rust or corrode $ General industrial storage, the default choice
Fiberglass composite MFG: -60°F to 250°F continuous, up to 300°F intermittent MFG: cutting oils, greases, radiation, pH 3.0 to 10.0 $$$ Heat, hot parts, harsh chemicals, wash lines
ESD See the data sheet Similar to polypropylene $$ Any bare electronic component handling
Clear polypropylene See the data sheet Similar to polypropylene $$ High-mix picking, visual inventory checks
Steel wire mesh See the data sheet Depends on the finish $$ Ventilation, wet or oily parts, full visibility
Worth knowing on food and pharma

Compliance can be color-specific, not just line-specific. On the LEWISBins PB series, all colors are FDA approved except yellow and red. If your application requires FDA-approved resin, confirm the specific color before ordering and ask us for documentation.

Section Four

Specialty bins that solve one specific problem well

Several products in this category look like premium versions of a standard bin. They are not. Each was designed around one problem.

Short answer: Indicator bins signal a reorder without software, the 1800-series fills 18 in deep shelving, stack-and-nest bins save space when empty, and 150 lb bins carry dense hardware.

Indicator bins: a reorder signal built into the bin

Classic two-bin kanban needs two containers per part number and the shelf space for both. An indicator bin does it in one. You stock the bin up to the divider that marks the reserve. Operators pick from the blue side until they reach the divider, then flip the bin so the orange side faces out. Orange facing the aisle is the reorder signal.

The result is a stock-out warning that needs no scanning, no counting and no software, and that a supervisor can read from down the aisle. Akro-Mils Indicator bins come in four sizes, 11-5/8 in or 17-7/8 in long and 4-1/8 in or 6-5/8 in wide, all 4 in high.

Extra-deep 1800-series bins: reclaiming dead shelf space

A 14-3/4 in long bin on an 18 in deep shelf leaves 3-1/4 in of unreachable space at the back. A 10-7/8 in bin leaves 7-1/8 in. That loss repeats on every shelf, on every level, across the whole run.

The Akro-Mils 1800-series is designed for 18 in deep shelving. Both models are 20-1/2 in long and 7 in high: the 30348 is 8-1/4 in wide with a 60 lb load rating, and the 30358 is 11 in wide with a 75 lb load rating. One width divider is included with each bin, and more are available.

Worked example: what the longer bin gains
  • Same width and height, more length: 20-1/2 in divided by 14-3/4 in is 1.39, so the 1800-series bin holds about 39% more than a 14-3/4 in bin with the same 8-1/4 in by 7 in cross-section.
  • Across the shelf: four 8-1/4 in wide bins take 33 in, so they fit a shelf with 36 in of clear width and leave 3 in to spare.
  • Per shelf: four bins at 39% more each is the same gain as adding about one and a half extra bins to every shelf level.

Stack-and-nest economy bins: for seasonal and variable inventory

These bins stack when full and nest inside each other when empty. If your parts volume swings through the year, or you ship bins out and get them back empty, nesting shrinks the empty-container footprint. See Akro-Mils economy hopper front bins.

Heavy-duty and giant bins: when the standard bin is the bottleneck

Load rating varies far more across this category than most buyers expect, and it is the spec that most often gets a bin replaced early.

Published load ratings
Product Published rating Notes
Akro-Mils ESD bin 30240 60 lb 14-3/4 in × 8-1/4 in × 7 in, black
Akro-Mils 1800-series 60 lb (30348), 75 lb (30358) 20-1/2 in long, for 18 in deep shelving
Akro-Mils Stak-N-Store 75 lb Three sizes, about 12-1/2 in high
Quantum Ultra Stack and Hang Up to 75 lb stack capacity on the largest bins Varies by model
Quantum Magnum 150 lb stacking capacity Ribbed reinforced walls, double wall thickness
Kadon heavy-duty hopper box 150 lb Two sizes, industrial-grade black plastic

For dense hardware, steel fittings and bulk fasteners, the jump from a 75 lb bin to a 150 lb bin is the difference between a container that holds its shape and one that bows, loses its stacking lip and eventually splits at a corner. For the largest sizes, also see Quantum giant stacking bins.

Section Five

Sizing: the step people rush and then regret

The two dimensions that decide whether an order works are the ones easiest to skip: inside dimensions, and the shelf the bin has to fit.

Short answer: Compare your part to the inside dimensions, not the outside. Measure the shelf before you shop, and size each bin for about two to four weeks of use.

Inside dimensions are the ones that matter

Catalog listings lead with outside dimensions because those decide shelf fit. Your part has to fit the inside, and the gap between the two is larger than most people assume once you allow for wall thickness, ribbing and the sloped hopper front.

Three published examples make the point:

Outside versus inside, in inches (length × width × height)
Bin Outside Inside Width lost
Akro-Mils 30240 14-3/4 × 8-1/4 × 7 14 × 6-9/16 × 6-3/4 1-11/16 in
LEWISBins PB1405-5 14-3/4 × 5-1/2 × 5 14-1/8 × 4-1/8 × 4-13/16 1-3/8 in
Kadon HH191107001000 19-1/4 × 11 × 6-3/4 16-1/2 × 9-1/2 × 6-1/4 1-1/2 in

If you are storing a part with a fixed footprint, such as a tray, a long fitting or a rigid bagged assembly, measure it and compare against the inside dimension. On a hopper front, the usable length at the bottom is shorter again because of the sloped front.

Match the bin to the shelf, not the other way around

Measure your shelf depth before you shop. A bin that overhangs the shelf edge is a snag hazard and will get knocked off. A bin that leaves several inches empty at the back is wasted space.

Shelf bins make this easy because the lengths are built around the shelf: 11-5/8 in for a 12 in deep shelf, 17-7/8 in for 18 in, and 23-5/8 in for 24 in. Then pick the width by part size and by how many bins you want across the shelf opening.

Size for turnover, not for capacity

A common instinct is to buy the largest bin that fits so refills are rare. That works against you. Oversized bins hold months of stock, which hides slow-moving inventory, buries older stock under newer, makes counting harder and makes the bin too heavy to lift down safely. A useful target, in our experience, is a bin that holds roughly two to four weeks of consumption for that part.

Use dividers before you buy a smaller bin

Most lines offer dividers that split one bin into compartments. When you have several low-volume part numbers, one divided bin often beats three small bins: fewer labels to maintain, less space lost between bin walls, and one shelf position instead of three. Dividers are model-specific, so order them with the bin.

Practical sizing checklist
  1. Measure shelf depth and usable height.
  2. Measure your largest part in all three dimensions.
  3. Estimate two to four weeks of usage by volume.
  4. Compare against inside dimensions.
  5. Weigh a full load and compare it against the bin's rating.
  6. Decide on dividers now, not later.
Section Six

Mounting and storage systems: the half of the purchase people forget

A stack and hang bin's rear hanging tab is only useful if you buy something for it to hang on. This is where a bin order becomes a storage system.

Short answer: Use louvered panels where the part mix changes, steel rails where wall space is tight, bench racks at the workstation, and rail racks on the floor between work areas.

Flexible wall and floor storage

Louvered panels

Steel panels with horizontal louvers that accept bin hanging tabs anywhere along their length. Bins reposition in seconds with no tools as your part mix changes. See single and double sided louvered panel floor racks.

Space-saving wall storage

Steel rails

Individual horizontal rails mounted directly to a wall. Lower profile than a full panel, and you can space rows to suit your bin heights. See wall mounted steel rails.

Point of use

Bench racks

Racks that sit on a workbench and bring the parts used at that station within arm's reach. See Akro-Mils bench racks.

Floor and aisle

Rail racks, single and double sided

Freestanding frames holding multiple rails. Double sided doubles capacity in the same footprint and works well between two work areas. See single and double sided rail racks.

Airflow and washdown

Chrome wire louvered panels

Wire panels that hang the same bins while letting air and light through. See Quantum chrome wire louvered panels.

Bulk storage

Shelving

Shelving loaded with matched bins. Confirm the bin length against the shelf depth and the bin widths against the clear shelf width before you order either.

Compatibility is not universal

Hanging tab profiles differ between manufacturers. A bin from one brand will not always seat correctly on another brand's louvered panel or rail. If you are adding to an existing system, tell us the brand and model of the panels or rails you already own and we will confirm the match before anything ships.

Section Seven

Brand by brand: what each line is known for

All five brands make good product. They are not aimed at the same buyer.

Short answer: Akro-Mils has the broadest system, Quantum the widest size range and the 150 lb Magnum, LEWISBins the FDA-approved colors, Kadon the large 150 lb hopper boxes, and MFG the fiberglass.

Akro-Mils

The broadest line we carry. The 30-Series stack and hang hopper front bin comes in 14 sizes, from the 30210 at 5-3/8 in × 4-1/8 in × 3 in up to the 30270 at 18 in × 16-1/2 in × 11 in.

Where Akro-Mils stands out is the depth of the system around that bin: the extra-deep 1800-series, Stak-N-Store bins rated at 75 lb, Indicator bins, ESD bins, hopper front shelf bins in 4 in and 6 in heights, storage drawers, and the panels, rails and racks to hang them on. If you want one brand across a whole facility, this is usually it.

Quantum Storage Systems

A very wide size range. We list 21 Ultra Stack and Hang models, from the QUS210 at 5-3/8 in × 4-1/8 in × 3 in up to the QUS270 at 18 in × 16-1/2 in × 11 in. Quantum publishes them as autoclavable up to 250°F and resistant to extreme cold, in blue, yellow, red, green, ivory, black and clear.

Above that sits the Magnum line in high-density polypropylene with ribbed reinforced walls and double wall thickness. Five models run from the QMS531 at 19-3/4 in × 12-3/8 in × 5-7/8 in to the QMS743 at 29 in × 18-3/8 in × 11-7/8 in, with a 150 lb stacking capacity and a published range of -40°F to 250°F. Quantum also covers stackable shelf bins, clear, conductive, wire mesh and giant stacking bins.

LEWISBins

Stack and hang bins and shelf bins, both with a hopper front. We list 13 4 in shelf bins in 11-5/8 in, 17-7/8 in and 23-5/8 in lengths. On the PB series, all colors are FDA approved for food contact except yellow and red, which makes LEWISBins a common pick for food, pharmaceutical and clean production areas.

Kadon

A focused line: large, high-capacity black hopper boxes in industrial-grade plastic. Two sizes, 19-1/4 in × 11 in × 6-3/4 in and 23-1/2 in × 11 in × 9 in, both rated at 150 lb. Built for heavy fasteners, dense fittings and steel hardware, with hopper access so you never lift a loaded box off the shelf.

MFG (Molded Fiber Glass Tray)

The specialist. Glass-reinforced composite containers with a published range of -60°F to 250°F continuous and up to 300°F intermittent, and resistance to mild acids and alkaline solutions within a pH of 3.0 to 10.0. We list four MFG fiberglass hopper bins, from 10 in × 6 in × 2-7/8 in up to 24.1 in × 16.3 in × 8 in. When plastic will not survive, this is the line.

Section Eight

Choosing by application

Find the row that matches your situation.

Short answer: Start from the environment and the load, then pick the style. Heat means fiberglass, static means ESD, heavy means 150 lb rated, and everything else usually means a polypropylene hopper front bin.

Assembly line, high pick frequency, room-temperature parts
Polypropylene stack and hang bins on bench racks or louvered panels at the station. Add clear bins where similar parts sit side by side. Size for two to four weeks of stock.
Electronics assembly or board repair
ESD bins throughout, in the 104 to 1011 ohms per square dissipative range. Drawer bins for high part-number component storage.
Heat treat, foundry, hot chips, paint or coating lines
MFG fiberglass composite. The -60°F to 250°F range, with up to 300°F intermittent, is the reason this line exists.
Maintenance stores prone to stock-outs
Indicator bins on louvered panels. A visual reorder signal with no software and no counting. Pair it with clear labels and a defined reorder point per bin.
Distribution and fulfillment picking
Hopper front shelf bins matched to the shelf depth and sized to how fast each part moves. Fast movers get wider or 6 in high bins at waist height. Slow movers get divided bins on upper and lower shelves.
Heavy hardware, fasteners, steel fittings
Kadon heavy-duty hopper boxes or Quantum Magnum, both published at 150 lb. Do not put dense hardware in a light bin and expect it to hold its shape.
Food, pharmaceutical, clean production
FDA-approved resin, with the color confirmed. LEWISBins PB series colors are FDA approved except yellow and red. Use wire panels where washdown and airflow matter.
18 in deep industrial shelving already installed
1800-series extra-deep bins at 20-1/2 in long. About 39% more volume per shelf position than a 14-3/4 in bin of the same width and height.
Wet, oily or freshly washed parts
Wire mesh bins for drainage and airflow, or fiberglass composite where cutting oils and detergents are constant.
Seasonal volume swings, or bins that ship out and return empty
Stack-and-nest economy bins. Nesting shrinks the empty footprint so you are not storing air in your off season.
Very small footprint, very many part numbers
Drawer bins on the bench, with dividers in each drawer.
Section Nine

Common and costly mistakes

These come up repeatedly on quote calls. Each one is cheap to avoid before the order and expensive after.

Short answer: The mistakes that cost the most are ordering to outside dimensions, ignoring the load rating, and buying bins without the panels or rails to hang them on.

Ordering to outside dimensions

The inside is smaller than you think, and on a hopper front the bottom is shorter still. Check the part against the inside dimensions.

Ignoring the load rating

Published ratings in this category run up to 150 lb, and many bins are rated far lower. A bin loaded past its rating bows, loses the shape of its stacking lip, and makes everything stacked above it less stable.

Buying bins without the mounting hardware

A stack and hang bin's rear tab does nothing on a bare shelf. If the bins are going on shelving, a shelf bin sized to the shelf depth is usually the better buy. If they are going on a wall or a bench, the hardware is part of the order. Budget the panels, rails or racks in the same order so the system is complete when it arrives.

Mixing brands on the same panel

Hanging tab shapes vary. Bins that do not seat properly fall off. Confirm compatibility before adding a second brand to an existing installation.

Using short bins on deep shelving

Several inches of unreachable space at the back of every shelf adds up to a real share of storage you are already paying for. Extra-deep bins recover it.

Skipping color-coding

Code by department, by part family, by supplier or by inspection status. Operators find a color faster than they read a label.

Assuming compliance applies across a whole line

FDA approval can be color-specific. ESD requires a specific material, not just a black bin. Ask for documentation on the exact model and color you are ordering.

Oversizing to reduce refills

Big bins hide old stock, complicate counting and get too heavy to lift down safely. Size to turnover instead.

Section Ten

Care, cleaning and getting a long service life

These bins are durable, not indestructible. A few habits extend their life.

Short answer: Keep loads under the rating, stack on level surfaces, check hanging tabs for cracks, and confirm the temperature limit for your model before steam cleaning.

  • Cleaning. Quantum publishes its Ultra Stack and Hang bins as autoclavable up to 250°F. For any other line, confirm the temperature limit on the data sheet before steam cleaning or autoclaving.
  • Check chemical compatibility. If you use an aggressive solvent or cleaner regularly, check the manufacturer's compatibility data for that chemical instead of assuming.
  • Do not overload, even briefly. In our experience a plastic bin held over its rating for weeks can deform for good even if it never cracks, and a deformed stacking lip is a hazard for everything above it.
  • Stack on level surfaces only. Stacking ledges are made for an even vertical load. An uneven or overhanging stack puts the force on one corner.
  • Inspect hanging tabs. On wall-mounted bins the tab carries the full load. Look for whitening or hairline cracks during routine walkthroughs.
  • Keep spares of your standard sizes. Standardizing on a handful of models means a damaged bin gets replaced from stock the same day.
Section Eleven

Frequently asked questions

The questions that come up most often on quote calls.

Do shelf bins have a hopper front?

Yes. A shelf bin has a cut-down hopper front so you can see and pick the parts while the bin sits on the shelf. Akro-Mils describes its 4 in shelf bin as having a wide hopper front, and LEWISBins publishes a raised hopper front on its shelf bins.

What is the difference between a stack and hang bin and a shelf bin?

Both have a hopper front. A stack and hang bin stacks on other bins and has a rear tab so it can hang on a louvered panel or rail. A shelf bin is long, narrow and low, made to sit in rows on shelving. Akro-Mils and LEWISBins shelf bins come in 11-5/8 in, 17-7/8 in and 23-5/8 in lengths for 12 in, 18 in and 24 in deep shelves, and take dividers.

Are bins from different manufacturers interchangeable on the same rack?

Not always. Rear hanging tab profiles differ between brands, so a bin from one manufacturer may not seat securely on another's louvered panel or rail. If you are expanding an existing setup, give us the brand and model of your current panels or rails and we will confirm the match before shipping.

When is fiberglass worth the extra cost over plastic?

When heat or chemicals are involved. MFG publishes its fiberglass composite for continuous use from -60°F to 250°F and intermittent use up to 300°F, and states it will not melt when in contact with most hot objects. It also resists cutting oils, greases, radiation, and mild acids and alkaline solutions within a pH of 3.0 to 10.0.

Do I need ESD bins, or is a regular black bin enough?

Color does not make a bin ESD-safe. A true ESD bin is molded from a static-dissipative material with a published rating. Akro-Mils publishes 104 to 1011 ohms per square for its ESD bins. If you handle bare boards or other static-sensitive components, use a bin with a published ESD rating.

What size bin fits 18 inch deep shelving?

The Akro-Mils 1800-series is designed for 18 in deep shelving. Both models are 20-1/2 in long and 7 in high. The 30348 is 8-1/4 in wide and rated at 60 lb, and the 30358 is 11 in wide and rated at 75 lb.

How many bins do I need?

Start from part numbers, not shelf space. Count the distinct parts stored at that location, then decide how many can share a divided bin. Add some room for growth, then confirm the total fits your shelving, panels or racks.

Can these bins go in an autoclave?

Some can. Quantum publishes its Ultra Stack and Hang bins as autoclavable up to 250°F. Confirm the limit for your exact model, and if you need FDA-approved resin, note that approval can be color-specific on some lines.

What is an indicator bin, and do I need one?

It is a single bin with a divider that marks a reserve. Operators pick from the blue side until they reach the divider, then flip the bin so the orange side faces out, which signals a reorder. It needs no software. If a line has stopped or a repair has waited because something ran out unnoticed, it is worth trying on your most-used consumables.

Can I mix bin sizes on one louvered panel?

Yes. Louvered panels accept hanging tabs along their length, so you can run large bins at the bottom, medium in the middle and small at the top, then rearrange as your part mix changes.

How much weight can I put in a bin?

Check the rating for the exact model, since it varies widely. Akro-Mils Stak-N-Store bins are rated at 75 lb. Quantum Magnum bins have a 150 lb stacking capacity, and Kadon heavy-duty hopper boxes are rated at 150 lb. Weigh a full load instead of estimating, since dense hardware is heavier than it looks.

Are dividers worth it, or should I buy smaller bins?

Dividers usually win. One divided bin holding four part numbers takes one shelf position instead of four and wastes no space on the walls between bins. Buy dividers with the bin, since they are model-specific.

Section Twelve

Quick-reference spec table

Published figures for the products referenced in this guide. Verify the exact model before ordering, since specs vary within every line.

Published specifications, sizes in inches (length × width × height)
Line Material Sizes Published load rating Published temperature
Akro-Mils 30-Series Plastic, stack and hang, hopper front 14 sizes, 5-3/8 × 4-1/8 × 3 up to 18 × 16-1/2 × 11 See listing See data sheet
Akro-Mils 4 in shelf bins One-piece molded polymer, wide hopper front, nests when empty 13 sizes, 11-5/8, 17-7/8 or 23-5/8 long, 2-3/4 to 11-1/8 wide, 4 high See listing See data sheet
Akro-Mils ShelfMax 6 in shelf bins Plastic, raised hopper front, reinforced side ribs 9 sizes, 11-5/8, 17-7/8 or 23-5/8 long, 4-1/8 to 11-1/8 wide, 6 high See listing See data sheet
LEWISBins 4 in shelf bins Plastic, raised hopper front, rolled rim 13 sizes, 11-5/8, 17-7/8 or 23-5/8 long, 2-3/4 to 11-1/8 wide, 4 high See listing See data sheet
Quantum stackable shelf bins FDA-approved material, raised front opening 10 sizes, 12 to 20-1/2 long, 6 to 11 wide, 7 high See listing Autoclavable to 250°F
Akro-Mils 1800-Series Plastic, one divider included 30348: 20-1/2 × 8-1/4 × 7. 30358: 20-1/2 × 11 × 7 60 lb (30348), 75 lb (30358) See data sheet
Akro-Mils Stak-N-Store Plastic Three sizes, including 17-1/2 × 10-7/8 × 12-1/2 75 lb See data sheet
Akro-Mils Indicator bins Plastic, blue and orange sides Four sizes, 11-5/8 or 17-7/8 long, 4 high See listing See data sheet
Akro-Mils ESD bins Static dissipative, 104 to 1011 ohms per square 30240 ESD: 14-3/4 × 8-1/4 × 7 60 lb (30240) See data sheet
Quantum Ultra Stack and Hang Injection-molded polypropylene 21 models, 5-3/8 × 4-1/8 × 3 up to 18 × 16-1/2 × 11 Up to 75 lb stack capacity on the largest bins Autoclavable up to 250°F
Quantum Magnum High-density polypropylene, ribbed, double wall 5 models, 19-3/4 × 12-3/8 × 5-7/8 up to 29 × 18-3/8 × 11-7/8 150 lb stacking capacity -40°F to 250°F
LEWISBins PB Series Polypropylene. FDA approved except yellow and red PB1405-5: 14-3/4 × 5-1/2 × 5 See listing See data sheet
Kadon heavy-duty hopper box Industrial-grade plastic, black 19-1/4 × 11 × 6-3/4 and 23-1/2 × 11 × 9 150 lb See data sheet
MFG fiberglass hopper bins Glass-reinforced composite Four models, 10 × 6 × 2-7/8 up to 24.1 × 16.3 × 8 See listing -60°F to 250°F, up to 300°F intermittent
Before you order

"See listing" and "See data sheet" mark figures we did not find published on the sources reviewed for this guide. It does not mean the figure does not exist. For a load rating, temperature limit or compliance document on a specific model, call and we will pull the manufacturer data sheet.

About the author. Tom McGovern has worked in the industrial material handling industry since 1981, bringing over 45 years of hands-on experience helping businesses select the right equipment for their applications. His expertise includes specifying and quoting Akro-Mils, Quantum, LEWISBins, Kadon and MFG bins.

Questions about this guide? Call 866-333-0728 to speak with an experienced material handling specialist.

Ready for a quote?

Send us these details and a material handling specialist will reply, typically within one business day.

  • Dimensions
    Size of the load and the space it goes in
  • Load
    Weight per item, shelf or level
  • Quantity
    How many units you need
  • Delivery ZIP code
    For freight pricing
  • Drawing
    A sketch, photo or spec sheet, if you have one
Get a Fast Quote Call 866-333-0728

Not sure which bin fits?

Tell us the part, the shelf and the environment, and we will spec it. Quotes are reviewed by material handling specialists, typically within one business day.

866-333-0728

Browse small parts bins at custommhs.com

No bots. No guesswork. Real experts.

Sources

Akro-Mils published product data · Quantum Storage Systems published product data · MFG Tray published product data · CustomMHS product listings for Akro-Mils, Quantum, LEWISBins, Kadon and MFG.

Disclaimer. This guide is educational content and reflects the opinion and general experience of CustomMHS. Sizes, load ratings and temperature limits are manufacturer-published figures and are subject to change. Confirm critical specifications against the current data sheet for your exact model before ordering. Reviewed November 2026.