Industrial Equipment Experts Since 1980 | Mon–Fri, 7 AM–6 PM ET
No bots. Real experts. 866-333-0728
Get a Fast Quote
Get a Fast Quote

CustomMHS Buyer's Guide

How Thick Should an Anti-Fatigue Mat Be? Choosing Mats for Dry, Wet and Oily Areas

Thicker is not automatically better. The right thickness depends on how long people stand in one spot, and the right material depends on what is on the floor.

Written and reviewed by: Tom McGovern, owner of CustomMHSPublished: November 2026Covers: Apache Mills anti-fatigue mattingQuestions: 866-333-0728
Section One

How thick should an anti-fatigue mat be?

Start with how people stand, not how soft the mat feels.

Short answer: Use 1/2 in. for general standing work. Step up to 5/8 or 11/16 in. when people stand in one place most of a shift. Use 15/16 in. only for extended static standing.

Quick answers
  • 1/2 in.: General standing work. Most of the market.
  • 5/8 to 11/16 in.: Standing in one place most of a shift with little walking.
  • 15/16 in.: Extended static standing only.
  • Material: Dry mats for dry floors, drainage mats for wet floors, nitrile for oil and grease.

An anti-fatigue mat works by making you shift your weight slightly, which keeps the leg muscles working and the blood moving. A mat that is too soft overworks the muscles instead. Published guidance compares it to jogging on beach sand.

A note on this guide

This guide is written from published manufacturer data and my own experience quoting this equipment. It is general guidance and my opinion, not engineering advice. Confirm the rating for your exact model and application before you order.

Section Two

Thickness by job

The lines we carry run from 1/2 in. to 15/16 in.

Short answer: Past 1/2 in., mats differ more by construction and surface than by thickness.

Apache Mills dry area mats by thickness
ThicknessProductsPositioned as
15/16 in.Ultimate Diamond FootMaximum cushioning for extended standing
11/16 in.Supreme Diamond Foot, Supreme SlipTechPremium comfort; SlipTech prioritizes slip resistance
5/8 in.Supreme Soft FootEnhanced softness
9/16 in.Diamond FootMid-range cushioning
1/2 in.Invigorator, Bubble Flex, Marble Foot, K-Marble Foot, Diamond Deluxe Soft Foot, ArmorStep FootStandard duty, widest choice of surfaces

Thick mats have a cost

A 15/16 in. mat is nearly an inch of step-up at the edge. That matters to feet and it matters much more to wheels. Where carts or pallet jacks cross the mat, choose a thinner mat and make sure the edges are beveled.

Specify beveled edges

Square edges are trip hazards. Beveled or ramped edges should be standard on every mat, and they are essential where carts or pallet jacks cross.

Section Three

Dry areas

The widest choice and the simplest decision.

Short answer: On a dry floor, choose by standing time and by how much wheeled traffic crosses the mat.

Dry area materials
MaterialStrengthLimit
Closed-cell foam and spongeLightest, most comfort per dollarLeast durable under wheeled traffic. Fixed workstations only.
Vinyl and PVCLower cost, easy to cleanLess resilient and generally less oil-tolerant than nitrile
Composite or layeredCushioning core with a harder-wearing topCosts more than plain foam
Natural rubberResilientNo oil or grease resistance

For an assembly bench or a packing station, a 1/2 in. mat is the place to start. For a machine operator who does not move from one spot, look at 5/8 or 11/16 in. Browse dry area mats.

Section Four

Wet areas

A dry area mat in a wet area makes things worse.

Short answer: On a wet or washdown floor, use drainage matting with holes or an open grid so liquid passes through.

A solid mat on a wet floor traps liquid on top and underneath. It becomes slippery and it becomes a hygiene problem. Wet area mats have holes or an open grid so water drains through and the standing surface stays clear.

  • Debris. Check that what is on your floor will actually pass through the holes. Fine debris and food solids can block them.
  • Cleaning. The mat has to be lifted and cleaned underneath. Wet area mats are often heavy by design, so weigh the cleaning burden against stability.
  • Sanitation. In food and beverage areas, put lifting and cleaning in the written sanitation schedule.
  • Slip resistance. Slip resistance is measured as a coefficient of friction. The NFSI B101.3 benchmark is a wet dynamic figure greater than 0.42 for level floors. Ask for the figure, the test method and whether it was measured wet.

Browse wet area matting.

Section Five

Oily and greasy areas

The material matters more than the thickness.

Short answer: Where oil or grease reaches the floor, use nitrile rubber. Natural rubber breaks down on petroleum products.

Rubber compounds and oil
CompoundOil and greasePublished temperature range
Nitrile (NBR)Resists oil, grease and some fuelsAbout -20°F to 170°F
Natural rubberNo resistance; degrades on petroleum productsSee data sheet

Machine shops, maintenance bays and commercial kitchens are nitrile applications. In a kitchen you need both drainage and grease resistance. Both nitrile and natural rubber are attacked by ozone and have poor UV resistance, so neither belongs outdoors without a rating for it.

Special cases: use flame-resistant welding matting under hot work, since standard rubber or foam there is a fire risk. Use ESD matting as part of a grounded static control system, and insulating switchboard matting in front of electrical panels.

Section Six

Choosing by station, and when to replace

Find your row, then put the mat on a replacement cycle.

Short answer: Matting is a consumable. Replace it when a thumb press leaves it compressed.

Packing or assembly bench, people move around
1/2 in. dry area mat.
Machine operator standing in one spot
5/8 or 11/16 in.
Inspection or checkout, standing still all shift
15/16 in., with beveled edges.
Carts or pallet jacks cross the mat
Thinner mat, beveled edges.
Washdown, dish room, wet process
Drainage mat.
Machine shop, cutting oil, grease
Nitrile.
Commercial kitchen
Drainage plus grease resistance.
Welding
Flame-resistant welding mat.

Replace a mat when a thumb press leaves it compressed, or when you see worn depressions, curling, cracking or splitting. Lift mats and clean under them. That is where moisture and debris collect.

More in our matting guide.

Section Seven

Frequently asked questions

The questions I hear most on quote calls.

How thick should an anti-fatigue mat be?

Use 1/2 in. for general standing work, 5/8 or 11/16 in. when people stand in one place most of a shift, and 15/16 in. only for extended static standing.

Is a thicker anti-fatigue mat better?

Not automatically. A mat that is too soft overworks the leg muscles, and a thick mat is a bigger step-up for feet and wheels.

What kind of mat do I need for a wet area?

A drainage mat with holes or an open grid so liquid passes through. A solid dry area mat traps liquid and becomes slippery.

What mat should I use around oil and grease?

Nitrile rubber. It resists oil, grease and some fuels. Natural rubber degrades on petroleum products.

Can carts roll over anti-fatigue mats?

Yes, with a thinner mat and beveled edges. Foam and sponge mats are the least durable under wheeled traffic.

When should I replace an anti-fatigue mat?

When a thumb press leaves it compressed, or when you see worn depressions, curling, cracking or splitting.

About the author. Tom McGovern is the owner of CustomMHS, an industrial material handling distributor serving the US, Canada and Mexico. He has worked in material handling since 1981 and has quoted and specified the Apache Mills dry area anti-fatigue mats and wet area matting sold at CustomMHS. Questions about this guide: 866-333-0728.

Ready for a quote?

Send us these details and a material handling specialist will reply, typically within one business day.

  • Dimensions
    Size of the load and the space it goes in
  • Load
    Weight per item, shelf or level
  • Quantity
    How many units you need
  • Delivery ZIP code
    For freight pricing
  • Drawing
    A sketch, photo or spec sheet, if you have one
Get a Fast Quote Call 866-333-0728

Not sure which mat fits the station?

Tell us how long people stand there, what is on the floor and whether carts cross it, and we will recommend a mat. Quote requests are answered within 24 hours by a real person.

866-333-0728

Browse dry area anti-fatigue matting at custommhs.com

Browse wet area matting

Get a fast quote

No bots. No guesswork. Real experts.

Specification sources

CustomMHS matting guide and Apache Mills listings · NFSI B101.3 · published rubber compound data.

Published figures are current as of November 2026 and are subject to change by the manufacturer. This guide is written from published manufacturer data and my own experience quoting this equipment. It is general guidance and my opinion, not engineering advice. Confirm the rating for your exact model and application before you order.