Industrial Equipment Experts Since 1980 | Mon–Fri, 7 AM–6 PM ET
No bots. Real experts. 866-333-0728
Get a Fast Quote
Get a Fast Quote

CustomMHS Buyer's Guide

Anti-Fatigue & Safety Matting

The instinct is that a thicker, softer mat is a better mat. Past a point the opposite is true: too much give overworks the muscles and adds fatigue. Here is what a mat really does, and how to buy one that does it.

Covers: Apache Mills anti-fatigue, wet-area and tacky matting Questions: 866-333-0728 Written and reviewed by: Tom McGovern · November 2026
Section One

What a mat is really doing

It is not cushioning your feet. It is making your legs move.

Quick answers
  • An anti-fatigue mat works by causing small, constant movements in the legs, which keeps blood circulating. It is not a pillow.
  • Softer is not better. Too much give makes the muscles work to stay balanced and adds fatigue.
  • Our Apache Mills dry-area mats run from 1/2 in to 15/16 in thick. Wet-area mats run from 1/2 in to 7/8 in.
  • Oil on the floor means nitrile rubber. Water on the floor means a drainage mat. A mat in a walkway needs beveled edges.

The common picture of an anti-fatigue mat is something soft between a hard floor and a tired foot. That is not how it works, and knowing how it does work changes what you buy.

Standing still on a hard floor keeps the leg muscles tensed. Blood flow drops and blood pools in the lower legs. That poor circulation is a main cause of the fatigue people report. The legs are not tired from impact. They are tired from standing still.

A mat interrupts that. Its slight give makes the body sway a little, too little to notice, and the calf and leg muscles make small corrections. Those small movements act like a pump and keep blood moving.

A second effect

Published ergonomics research also describes how long standing keeps the same small group of muscle fibers working without rest, which is where aches begin. A surface that shifts the pressure points under the foot spreads that work across more fibers.

So what you are buying is controlled give: enough to cause sway and vary the pressure points, not so much that the muscles work hard to hold you upright.

Please read this part

This guide is educational and reflects the opinion and general experience of CustomMHS as an equipment distributor. It is not an ergonomic assessment or compliance guidance. Thicknesses and colors are the manufacturer's published figures and can change. Confirm the current data sheet for your exact model before you order.

Section Two

The too-soft trap

This is the finding that surprises people, and it reverses the way most buyers shop for mats.

Short answer: Past a point, more give means more fatigue. Trial a mat for a full shift, not five minutes.

If a little movement is good, it seems more give should be better. It is not. Matting industry technical literature is direct about it: too much softness overworks the muscles and causes more fatigue. The comparison usually given is jogging on dry beach sand. It feels forgiving for a few steps and is exhausting over distance, because every step needs the muscles to steady you on a surface that will not hold still.

What works is narrower than "as soft as possible":

  • Moderate cushioning that causes small movements without real muscular effort.
  • Even support under both feet.
  • A surface that varies the pressure points.
Why this matters when you trial mats

A worker trying mats will often pick the softest one in the first five minutes, because it feels best right away. That is a poor guide to hour seven. Trial a mat for a full shift and ask at the end of the day.

Section Three

Thickness and cushioning

Thickness is the easiest spec to compare and a weak guide to comfort by itself.

Short answer: Start at 1/2 in for general standing work. Step up to 5/8 in or 11/16 in for people who stand in one spot most of the shift. Save 15/16 in for long static standing.

Apache Mills dry-area mats we list
Mat Thickness Colors Listed as
Ultimate Diamond Foot 15/16 in 4 Thickest cushioning in the line, for extended standing
Supreme Diamond Foot 11/16 in 8 Widest color selection
Supreme SlipTech 11/16 in 2 Added slip resistance alongside comfort
Supreme Soft Foot 5/8 in 1 See listing
Diamond Foot 9/16 in 8 See listing
Invigorator Black 1/2 in 2 See listing
Bubble Flex 1/2 in 1 See listing
Marble Foot 1/2 in 5 Wide color selection
K-Marble Foot 1/2 in 3 See listing
Diamond Deluxe Soft Foot 1/2 in 2 See listing
ArmorStep Foot 1/2 in 1 See listing

Six of the eleven lines are 1/2 in thick and differ in construction and surface. That is the useful signal. Past a point, the manufacturer stops adding thickness and changes what the mat is made of and how the top is textured. See Apache Mills dry-area anti-fatigue mats.

How to choose

  1. Start at 1/2 in for general standing work.
  2. Step up to 5/8 in or 11/16 in where people stand in one place for most of a shift.
  3. Go to 15/16 in only for long static standing, and remember section two.
  4. Then choose the surface for traction and cleaning, and the color for your floor marking plan.
A thicker mat is a taller step

A 15/16 in mat is nearly a 1 in step up. That is an obstacle to a cart wheel, a pallet jack and a foot, so the edge matters more as thickness goes up. See section seven.

Section Four

Slip resistance, stated plainly

There are published numbers. There is also real disagreement about them. You should know both.

Short answer: Ask for the friction figure and the test method together. Treat the number as one input, because OSHA does not set a friction value.

Slip resistance is measured as a coefficient of friction: the sideways force needed to make a shoe slide, divided by the downward force on it. It is measured static, from a standstill, and dynamic, already moving. Dynamic figures are usually written DCOF.

The benchmark quoted most often comes from the NFSI B101.3 standard, which classes a wet DCOF above 0.42 as high traction on level floors.

What the number does not do

OSHA's walking-working surfaces rule, 29 CFR 1910.22, requires floors to be kept clean and, as far as feasible, dry. It does not set a coefficient of friction. Test methods are also debated among specialists. A figure on a data sheet is useful. It is not a compliance certificate, and it does not replace keeping the floor safe.

  • Ask for the figure and the method. A number without wet or dry, static or dynamic, and the standard used cannot be compared to anything.
  • Test in your conditions. Your liquid, your footwear, your floor. A mat tested with water may behave differently under cutting oil.
  • Treat the surface as a working feature. Apache Mills lists Supreme SlipTech for dry areas and Safety Tru-Tread for wet areas where slip resistance is the priority.
  • Footwear is half the system. The best mat will not save a worn, smooth sole.
Section Five

Material by what is on the floor

What reaches your floor decides the material. Get it wrong and the mat breaks down instead of wearing out.

Short answer: Oil, grease or cutting fluid calls for nitrile rubber. Natural rubber is good value on a clean, dry floor and a poor choice anywhere oil reaches it.

Where there is oil

Nitrile rubber

Nitrile is chosen for its resistance to oil and grease. It is the material for machine shops, maintenance bays and anywhere petroleum products reach the floor.

Where there is not

Natural rubber

Tough and resilient, and good value in a clean, dry area. It lacks oil and grease resistance and breaks down when petroleum products reach it.

Both prefer to stay indoors

Sunlight and ozone attack both nitrile and natural rubber. For a dock apron or an outdoor walkway, ask about the outdoor rating of the exact mat. Do not assume an indoor mat will hold up.

Other materials

  • Vinyl and PVC: lower cost and easy to clean, for dry commercial and light industrial areas.
  • Foam and sponge: light and comfortable for the money, and the least durable under wheels. Good at a fixed station, not in a traffic lane.
  • Layered constructions: a cushion core under a harder-wearing top surface, which is how a mat gets comfort and durability together.

The material and chemical resistance of each mat is on its listing or data sheet. If oil, grease or chemicals are involved, tell us what they are and we will confirm the match.

Section Six

Wet areas and drainage

A different product, not a variation on the dry-area mat.

Short answer: In a wet area, use a mat made for it. A solid dry-area mat traps liquid underneath and gets slick on top.

Apache Mills wet-area mats we list
Mat Thickness Colors Listed as
Safety Tru-Tread 7/8 in 2 Choose when slip resistance is the top priority
Tru-Tread 7/8 in 3 Maximum cushioning
Performa 5/8 in 3 See listing
Performa SD 5/8 in 1 See listing
Work Step 1/2 in 3 Thinner, lower profile

Wet-area mats are made for spills, splashes and washdown. A solid dry-area mat in a wet area does the opposite of what you want: it holds liquid underneath, gets slippery on top, and becomes a cleaning problem in food areas. See Apache Mills wet-area anti-fatigue mats.

What to confirm:

  • Does liquid clear? Drainage openings only work if what is on your floor passes through them. Food solids and fine debris block small openings.
  • Can it be lifted? The floor under a wet-area mat is where problems build up. Mats that are practical to lift get cleaned.
  • Is there grease? Then check the material for grease resistance.
  • How heavy is it? Weight keeps a mat in place and makes it harder to lift for cleaning. Check both.
The mat is part of your cleaning plan

In food, beverage and pharmaceutical areas, put lifting and cleaning under the mats in the written schedule, at a stated frequency, like any other surface.

Section Seven

When the mat is the trip hazard

A mat is a safety product that can create the hazard it was bought to prevent.

Short answer: Buy beveled edges, watch for curled corners, and stop mats from sliding.

Every mat adds an edge, and an edge is a change in floor height.

Edges

Square edges catch

A beveled edge lets a foot, a cart wheel and a pallet jack ride up instead of catching. Treat a square-edged mat in a walkway as a problem.

Curling

Corners lift over time

Heat, cleaning chemicals, age and dragging all curl corners. It happens slowly, so nobody notices the day it becomes a hazard. Inspect for it.

Sliding

Mats move

A mat that creeps across the floor opens gaps and rides up against equipment. Weight and backing address this.

The honest view

A mat helps with fatigue. Whether it helps or hurts with slips and trips depends on the right mat, the right size, proper edges, and keeping it flat and clean. A neglected mat is worse than no mat.

Section Eight

Coverage and layout

Where the mat goes and how far it reaches matters as much as which one you buy.

Short answer: Size the mat to where the person moves, not where they stand. One runner beats a row of small mats.

Worked example: a packing bench

A packing bench is 6 ft long. The packer steps about 1 ft past the left end to reach the carton stack and about 1 ft past the right end to reach the tape and labels.

Sizing the mat to the work
Step Math Result
Length 6 ft bench + 1 ft left + 1 ft right 8 ft
Depth Room to stand and take one step back 3 ft
Mat 3 ft × 8 ft 24 sq ft, one piece

A 2 ft × 3 ft mat centered on the bench would leave the packer stepping on and off the edge dozens of times an hour. That is a trip exposure, and it gives up the benefit you paid for.

Runners

On a production line or a long bench, one continuous runner is better than a row of separate mats, because separate mats put an edge between every station.

Color has a job

Several Apache Mills lines come in up to eight colors. Color can mark a walkway edge, identify a work cell, or make the mat edge easy to see. Pick colors that agree with your floor marking plan. Our floor marking tape guide covers color conventions.

Section Nine

Tacky mats and other specialty mats

Where a general anti-fatigue mat is the wrong product.

Short answer: Tacky mats pull dust off shoes at an entry point. Welding, electrical panel and static-control work each need a mat made and rated for that job.

Tacky mats

Apache Mills tacky mats have an adhesive surface that traps dust and debris from footwear at entry points. The layers peel off as they load up. They are standard at cleanroom entries and useful at any doorway into a paint, electronics or other dust-sensitive area. Our cleanroom guide covers entry procedures.

The weak point is the peeling. A loaded tacky mat does nothing, so put the peel frequency in a written schedule.

Mats for special hazards

  • Welding areas: use a mat made for welding and hot work. An ordinary rubber or foam mat under a welding station is a fire risk.
  • In front of electrical panels: insulating switchboard matting is protective equipment made to a standard such as ASTM D178, not a comfort mat.
  • Static-sensitive electronics: the mat is part of the static control system. Ask for a measured resistance and check it against your program. See our containers guide for the terms.

If you need one of these, call us with the application so the right rated product is quoted.

Section Ten

When a mat has stopped working

A mat keeps looking like a mat long after it has stopped acting like one.

Short answer: Press it with your thumb. If it does not spring back, it is finished. Put mats on a replacement cycle.

A mat that has packed down no longer produces the small movements described in section one. It is a thin layer of dead material on concrete, and the person on it gets the same fatigue as on a bare floor while everyone believes the problem is solved.

  • Press it with your thumb. A working mat springs back. One that stays dented or feels dense has taken a set.
  • Look for a hollow where people stand. That is where the mat has stopped working, and it is where the person stands.
  • Check every edge and corner for curling.
  • Check for cracks and splits, especially where oil, chemicals or sunlight reach the mat.
  • Lift it and look underneath for moisture and debris.
  • Check it still lies flat and has not moved.
  • Ask the people standing on it. "This mat feels flat now" is a reliable signal.
Budget for replacement

Matting is a consumable. Treating it as a one-time purchase is how a plant ends up with a floor full of dead mats.

Section Eleven

Choosing by application

Find the row that matches your situation.

Short answer: Dry floor: a 1/2 in dry-area mat with beveled edges. Wet floor: a wet-area mat. Oil: nitrile. Traffic: thinner and beveled.

Assembly, packing or inspection station, dry floor
A dry-area mat, 1/2 in to start, beveled edges, sized to where the person moves.
Standing in one place most of the shift
Step up to 5/8 in or 11/16 in. Trial it for a full shift before you buy for the whole floor.
Oil, grease or cutting fluid on the floor
Nitrile rubber. Natural rubber breaks down in petroleum products.
Wet or washdown area
A wet-area mat. Confirm liquid clears and the mat can be lifted for cleaning.
Food or beverage processing
A wet-area mat with grease resistance, and under-mat cleaning in the written schedule.
Carts or pallet jacks cross the area
Beveled edges, and a thinner mat so the step is smaller.
Long production line or bench
One continuous runner instead of separate mats.
Entry to a clean or dust-sensitive area
A tacky mat, with a peel schedule.
Slip resistance is the main concern
Supreme SlipTech in dry areas, Safety Tru-Tread in wet areas. Ask for the test figure and method.
You want color to match floor marking
Supreme Diamond Foot or Diamond Foot, each in 8 colors.
Outdoors or strong daylight
Ask about the outdoor rating of the exact mat.
People say the mats no longer help
Press them with a thumb. A mat that stays dented needs replacing.
Section Twelve

Common and costly mistakes

Most of these come from treating a mat as furniture instead of equipment.

Short answer: The big ones: buying the softest mat, using a dry mat in a wet area, sizing to the person instead of the work, and never replacing.

Assuming softer is better

Too much give overworks the muscles. Moderate cushioning is the goal.

Trialing mats for five minutes

The softest mat wins a five-minute test and can lose an eight-hour one.

Putting natural rubber where there is oil

Nitrile is the material for oily floors.

Using a dry-area mat in a wet area

It traps liquid and gets slippery.

Sizing to the person, not the work

If people step off the mat to reach things, they cross an edge all day.

Accepting square edges in a walkway

Beveled edges matter more as thickness goes up.

Treating a friction figure as compliance

OSHA does not set a coefficient of friction. Use the number as one input.

Never looking underneath

Moisture and debris collect under mats.

Buying mats once

A packed-down mat looks fine and does nothing.

Section Thirteen

Frequently asked questions

What comes up most often on quote calls.

How do anti-fatigue mats work?

The slight give in the mat makes the body sway a little, and the leg muscles make small corrections. Those movements keep blood circulating in the legs, which reduces the fatigue caused by standing still on a hard floor.

Is a thicker, softer mat better?

Not past a point. Too much give makes the muscles work to keep you balanced and adds fatigue. Moderate cushioning that causes small movements is the goal.

What thickness should I buy?

Start at 1/2 in for general standing work. Step up to 5/8 in or 11/16 in where people stand in one place most of the shift, and use 15/16 in only for long static standing.

What slip resistance figure should I look for?

The benchmark quoted most often is a wet DCOF above 0.42, which NFSI B101.3 classes as high traction. Ask for the test method with the number. OSHA does not set a coefficient of friction, so treat the figure as one input.

Nitrile or natural rubber?

Nitrile where oil, grease or cutting fluid reaches the floor. Natural rubber is good value on a clean, dry floor but breaks down in petroleum products.

Can I use a regular anti-fatigue mat in a wet area?

No. A solid dry-area mat traps liquid underneath and gets slippery on top. Use a mat made for wet areas.

Can a mat make a floor less safe?

Yes. Square edges, curled corners and mats that slide are trip hazards. Buy beveled edges, inspect for curling, and replace mats that no longer lie flat.

How big should the mat be?

Size it to where the person moves, not where they stand. For a 6 ft bench where the worker steps 1 ft past each end, that is a 3 ft by 8 ft mat.

How do I know when a mat needs replacing?

Press it with your thumb. A working mat springs back. If it stays dented, feels dense, or has a hollow where people stand, it has packed down and should be replaced.

What are tacky mats for?

They have an adhesive surface that pulls dust and debris off footwear at an entry point. The layers are peeled off as they load up.

Does mat color matter?

It can. Color can mark a walkway edge, identify a work cell or make the mat edge easier to see. Several Apache Mills lines come in up to eight colors.

Section Fourteen

Quick-reference tables

Published figures referenced in this guide.

Key points
Item Figure Source
Slip resistance benchmark Wet DCOF above 0.42 is classed as high traction on level floors NFSI B101.3
OSHA and friction Floors kept clean and, as far as feasible, dry. No coefficient of friction is set 29 CFR 1910.22
Dry-area thickness range 1/2 in to 15/16 in Apache Mills, per CustomMHS listing
Wet-area thickness range 1/2 in to 7/8 in Apache Mills, per CustomMHS listing
Product families we list
Family Listing Role
Dry-area anti-fatigue mats Apache Mills dry-area mats Standing comfort on hard, dry floors
Wet-area anti-fatigue mats Apache Mills wet-area mats Comfort and footing in wet and washdown areas
Tacky mats Apache Mills tacky mats Dust and debris control at entry points
Before you order

Confirm material, thickness, edge style, size and chemical resistance on the listing or data sheet for the exact mat. Tell us what is on your floor, how long people stand and whether anything rolls across, and we will specify it.

About the author. Tom McGovern has worked in the industrial material handling industry since 1981, bringing over 45 years of hands-on experience helping businesses select the right equipment for their applications. His expertise includes specifying and quoting Apache Mills dry-area mats, wet-area mats and tacky mats.

Questions about this guide? Call 866-333-0728 to speak with an experienced material handling specialist.

Ready for a quote?

Send us these details and a material handling specialist will reply, typically within one business day.

  • Dimensions
    Size of the load and the space it goes in
  • Load
    Weight per item, shelf or level
  • Quantity
    How many units you need
  • Delivery ZIP code
    For freight pricing
  • Drawing
    A sketch, photo or spec sheet, if you have one
Get a Fast Quote Call 866-333-0728

Tell us what is on the floor

Dry, wet, oily or greasy, plus how long people stand and whether carts cross it. Those four answers specify matting properly. Quotes are reviewed by material handling specialists, typically within one business day.

866-333-0728

Browse matting at custommhs.com

No bots. No guesswork. Real experts.

Sources

NFSI B101.3 · OSHA 29 CFR 1910.22 · ASTM D178 · published matting industry and ergonomics literature on prolonged standing · Apache Mills figures as published on CustomMHS product listings.

Disclaimer. This guide is educational content and reflects the opinion and general experience of CustomMHS. It is not an ergonomic assessment or compliance guidance. Slip resistance test methods are debated and OSHA does not set a coefficient of friction, so a published figure does not replace keeping walking surfaces safe. Confirm material and chemical resistance against the manufacturer's data. Reviewed November 2026.