Industrial Equipment Experts Since 1980 | Mon–Fri, 7 AM–6 PM ET
No bots. Real experts. 866-333-0728
Get a Fast Quote
Get a Fast Quote

CustomMHS Buyer's Guide

What Makes a Chair Cleanroom Rated? ISO Classes and Seating Explained

Cleanroom classes describe the air in a room, not the furniture in it. A cleanroom chair is one built so it does not spoil that air. Here is what to look for.

Written and reviewed by: Tom McGovern, owner of CustomMHSPublished: November 2026Covers: BioFit cleanroom chairs and stoolsQuestions: 866-333-0728
Section One

What makes a chair cleanroom rated?

It is about what the chair does not give off.

Short answer: A cleanroom chair is built from smooth, non-porous, cleanable materials so it sheds as few particles as possible, and it is offered in versions matched to a room's ISO class. The class itself belongs to the room, not the chair.

Quick answers
  • What the class measures: ISO 14644-1 classes limit the number of airborne particles in a cubic meter of room air.
  • How the chair is built: Vinyl or molded surfaces instead of fabric, and chrome-plated metal parts.
  • How it is ordered: BioFit cleanroom versions carry an IS06 or IS08 suffix for ISO 6 or ISO 8.
  • What to do: Confirm the class in writing on the quote.

This point matters because it is often stated loosely. The cleanroom standards typically do not apply to equipment and supplies used in a cleanroom. BioFit states that it aims to meet the particulate cleanliness goals of those standards. So a chair is built and offered for use in a given class of room, and you match it to your room's certification.

A note on this guide

This guide is written from published manufacturer data and my own experience quoting this equipment. It is general guidance and my opinion, not engineering advice. Confirm the rating for your exact model and application before you order.

Section Two

ISO classes explained

The lower the number, the cleaner the room.

Short answer: Each ISO class allows ten times more particles than the one before it. ISO 5 allows 3,520 particles of 0.5 micron or larger per cubic meter. ISO 8 allows 3,520,000.

ISO 14644-1 classes and Federal Standard 209E equivalents
ISO classMaximum particles of 0.5 micron or larger, per cubic meterFormer FS 209E class
ISO 335Class 1
ISO 4352Class 10
ISO 53,520Class 100
ISO 635,200Class 1,000
ISO 7352,000Class 10,000
ISO 83,520,000Class 100,000

Federal Standard 209E was the older US system. It counted particles per cubic foot, and the class number was the count: Class 100 meant 100 particles of 0.5 micron or larger per cubic foot. It was replaced by ISO 14644-1 in 2001, but the old class names are still used on the floor.

Worked example

Your room is certified ISO 7 and someone calls it a Class 10,000 room. Those are the same room. A chair offered for ISO 6 is built for a cleaner room than yours, so it is suitable. A chair offered only for ISO 8 is not, because ISO 8 allows ten times the particles your room does.

Section Three

How cleanroom seating is built

Every difference from an ordinary chair is about particles and cleaning.

Short answer: Cleanroom chairs replace fabric with vinyl or molded surfaces and use chrome-plated metal parts.

Upholstered, vinyl

Amherst, Elite, Belize, Eton, Bridgeport

A 3 in. upholstered seat covered in vinyl instead of fabric, with components described as cleanroom-compatible and chrome-plated metal parts.

Molded urethane

UniqueU chair, Cerex stool

Self-skinned urethane seat and back, 1-1/2 in. thick. Resists water, chemicals and paint. Recommended for demanding cleanroom applications.

Polypropylene

ArmorSeat

A tough non-porous seat and back with antimicrobial properties and UV inhibitors. Recommended for demanding cleanroom applications.

Material is the main choice. BioFit recommends the urethane and polypropylene models for demanding applications that need chemical resistance and sanitation, and positions fabric-upholstered series for lower-level environments. Smooth, non-porous surfaces are easy to sanitize.

Sealed upholstery is a separate feature

Vacuum-formed (VF) sealed upholstery resists fluid and bacterial infiltration. It is aimed at healthcare and is a different question from the ISO class. You can need one, the other or both.

Section Four

BioFit cleanroom series

The eight cleanroom models on our site.

Short answer: Choose by back size for the work, and by material for how aggressive the cleaning is.

BioFit cleanroom seating
SeriesTypeBackrestSeat
AM (Amherst)Upholstered chair18 in. W x 19 in. H21 in. W x 19 in. D x 3 in.
EE (Elite)Upholstered chair15-1/2 in. W x 14-1/2 in. H18-1/2 in. W x 17 in. D x 3 in.
BE (Belize)Upholstered chair15-1/2 in. W x 14-1/2 in. H18-1/2 in. W x 16-1/2 in. D x 3 in.
ET (Eton)Upholstered chair14-1/2 in. W x 9-1/2 in. H18-1/2 in. W x 17 in. D x 3 in.
BT (Bridgeport)Upholstered chair14-1/2 in. W x 9-1/2 in. H18-1/2 in. W x 16-1/2 in. D x 3 in.
UU (UniqueU)Molded urethane chair16-1/2 in. W x 12-1/2 in. H18-1/2 in. W x 17 in. D x 1-1/2 in.
GG (ArmorSeat)Polypropylene chair16 in. W x 10-3/4 in. H17-1/2 in. W x 15-1/2 in. D x 1-1/2 in.
CX (Cerex)Molded urethane lab stoolNone14 in. diameter x 1-1/2 in.

Standard BioFit chairs are rated 350 lb and carry a 13 year warranty for normal multishift use, with pneumatic cylinders covered for the functional lifetime of the chair. BioFit lists cleanroom ratings from ISO 3 through ISO 8 across its range. The stocked suffixes are IS08 and IS06, so confirm the class for the exact model on your quote.

Section Five

Seat height and static control

Two more things to settle on the same order.

Short answer: Seat height should center on your work surface height minus 12 in. If the room also handles electronics, order the static control version.

Seat height

Take the height of the work surface and subtract 12 in. That is the midpoint the seat height range should center on. A 36 in. bench gives 36 - 12 = 24 in., so you want a range with 24 in. near the middle.

BioFit seat height ranges
Height codeUpholstered seatUniqueU urethane on steel base
L, low17 to 22 in.17 to 21 in.
M, medium19 to 28 in.20 to 27 in.
H, high22 to 32 in.24 to 31 in.

For a 24 in. midpoint, the medium range fits. The exact range depends on the base, so check it on the model.

Static control

Many cleanrooms are also electronics rooms. BioFit static control chairs carry a K suffix and are tested to ANSI/ESD STM12.1 to support an ANSI/ESD S20.20 program. They ground through the seat, the cylinder and conductive casters or glides. Resistance values are not published on our listings, so request them before ordering, and only ever replace casters with ESD casters.

Section Six

How to specify, and common mistakes

Five facts, then five things to avoid.

Short answer: Give the room class, the bench height, the cleaning method, the static requirement and the floor.

  1. Room certification: the ISO class, or the old FS 209E class.
  2. Work surface height in inches.
  3. How the chair will be cleaned, and with what.
  4. Whether static control is required.
  5. Floor type, for casters or glides.
  • Fabric upholstery in a demanding cleanroom. Use vinyl, urethane or polypropylene there.
  • Reading the class numbers backwards. Lower class numbers are cleaner. A chair for ISO 8 does not suit an ISO 6 room.
  • Assuming every model covers every class. Get the class for the exact model on the quote.
  • Confusing sealed upholstery with a cleanroom rating. They are separate features.
  • Standard casters on an ESD chair. Standard casters break the ground path.

More in our chairs and stools guide.

Section Seven

Frequently asked questions

The questions I hear most on quote calls.

What makes a chair cleanroom rated?

It is built from smooth, non-porous, cleanable materials such as vinyl, molded urethane or polypropylene with chrome-plated metal parts, so it sheds few particles, and it is offered in a version matched to a room's ISO class.

What do ISO cleanroom classes mean?

ISO 14644-1 classes limit airborne particles per cubic meter of air. ISO 5 allows 3,520 particles of 0.5 micron or larger, ISO 6 allows 35,200, ISO 7 allows 352,000 and ISO 8 allows 3,520,000.

Is ISO 7 the same as Class 10,000?

Yes. Class 10,000 is the former Federal Standard 209E name for what ISO 14644-1 calls ISO 7. FS 209E was replaced in 2001.

Can I use a regular task chair in a cleanroom?

Use a cleanroom version matched to your room's class. Fabric-upholstered series are positioned for lower-level environments, and demanding rooms call for urethane or polypropylene.

What ISO classes are BioFit cleanroom chairs available for?

BioFit lists cleanroom ratings from ISO 3 through ISO 8 across its range. Stocked suffixes are IS08 and IS06. Confirm the class for the exact model on your quote.

How do I choose the seat height?

Subtract 12 in. from the work surface height. The result is the midpoint your seat height range should center on.

About the author. Tom McGovern is the owner of CustomMHS, an industrial material handling distributor serving the US, Canada and Mexico. He has worked in material handling since 1981 and has quoted and specified the BioFit cleanroom chairs and stools and BioFit molded urethane chairs sold at CustomMHS. Questions about this guide: 866-333-0728.

Ready for a quote?

Send us these details and a material handling specialist will reply, typically within one business day.

  • Dimensions
    Size of the load and the space it goes in
  • Load
    Weight per item, shelf or level
  • Quantity
    How many units you need
  • Delivery ZIP code
    For freight pricing
  • Drawing
    A sketch, photo or spec sheet, if you have one
Get a Fast Quote Call 866-333-0728

Need seating matched to your room?

Tell us your room's ISO class, the bench height and whether you also need static control, and we will specify the chair. Quote requests are answered within 24 hours by a real person.

866-333-0728

Browse BioFit cleanroom chairs and stools at custommhs.com

Browse all chairs and stools

Get a fast quote

No bots. No guesswork. Real experts.

Specification sources

CustomMHS chairs and stools guide and BioFit cleanroom seating listings · ISO 14644-1 · Federal Standard 209E (replaced in 2001).

Published figures are current as of November 2026 and are subject to change by the manufacturer. This guide is written from published manufacturer data and my own experience quoting this equipment. It is general guidance and my opinion, not engineering advice. Confirm the rating for your exact model and application before you order.