Section One
Why seating is a specification
A chair that does not fit the bench gets replaced, worked around, or blamed for an injury.
Quick answers
- Measure the work surface first. BioFit's rule is work surface height minus 12 in equals the ideal seat height midpoint. A 36 in bench calls for a 24 in seat height.
- BioFit task chairs come in three height classes: low, medium and high. Pick the class whose range is centered on your number.
- Most BioFit task chairs are rated at 350 lb. The Intensive Plus is rated at 500 lb and built for around-the-clock use.
- An ESD chair only works with ESD casters or glides. Standard casters break the path to the floor.
Industrial seating fails quietly. Nobody files a report because a stool is 2 in too low. The operator perches on the front edge, loses the backrest, and has a sore back that gets blamed on the job.
The fix is plain: seat height comes from the work surface, the base comes from the floor and the task, and the environment decides the materials. Comfort preferences come last.
What the line covers
BioFit builds its task seating on a common platform. Most task series share a 350 lb capacity, pneumatic seat height adjustment, a fixed 3-1/2 degree rearward seat tilt, backrest tilt and height adjustment, four base choices and three height classes. See BioFit multipurpose chairs.
Please read this part
This guide is educational and reflects the opinion and general experience of CustomMHS as a BioFit dealer. It is not an ergonomic assessment, a compliance assessment or medical advice. ESD and cleanroom qualification depend on your whole control program, not on one piece of equipment. Specifications, options and warranty terms are BioFit's published figures and can change, so confirm them on the listing or your quote.
Section Two
Reading a BioFit model number
Series, base, height class, mobility and environment, in that order.
Short answer: The first two letters are the series, the third is the base, then the height class (L, M or H), then casters or glides, then options, and the last segment is the finish or environment.
How the segments decode
| Segment |
Meaning |
Values |
| First two letters |
Series |
ET Eton, EE Elite, AM Amherst, BE Belize, BT Bridgeport, GG ArmorSeat, UU UniqueU, CX Cerex, RX Rexford, RT Regent |
| Third letter |
Base |
S is 23 in steel. A is 25.6 in cast aluminum. R is 25.6 in composite. W is 28.7 in wide aluminum |
| Next |
Height class |
L low, M medium, H high |
| Next |
Mobility |
RC casters, HG glides, RK ESD casters |
| Next |
Seat control |
T task control. Upgrades: FFAC, EXE, ASC |
| Next |
Footring and arms |
XF no added footring. XA no arms. ARS and PSAS are arm options |
| Final |
Finish or environment |
06 black. K static control. IS08 ISO Class 8. IS06 ISO Class 6 |
Two things to watch
ET is Eton and EE is Elite, which is easy to reverse. And ISO Class 8 shows up spelled two ways, IS08 and ISO8. They are the same thing. The Intensive Plus, the Aramis stools and the footrests use their own numbering.
Section Three
Matching seat height to the work surface
The decision the whole specification hangs on.
Short answer: Subtract 12 in from the work surface height to get the seat height to aim for, then choose the height class whose range has that number near its middle.
Published seat height ranges, 3 in upholstered series
| Class |
S base, 23 in steel |
A, R and W bases |
Published work surface match |
| L low |
18 to 22 in |
17 to 22 in |
29 to 34 in, desk height |
| M medium |
21 to 28 in |
19 to 26 in |
33 to 40 in, bench height |
| H high |
25 to 32 in |
22 to 32 in |
34 to 44 in, tall bench or counter |
Worked examples
- 30 in desk: 30 − 12 = 18 in. The low class covers it.
- 36 in bench: 36 − 12 = 24 in. The medium class on a steel base runs 21 to 28 in, with 24-1/2 in at its middle.
- 42 in counter: 42 − 12 = 30 in. The high class on a steel base runs 25 to 32 in.
- 40 in bench: 40 − 12 = 28 in, the very top of medium and the middle of high. If people sit for long stretches, the high class with a footring usually fits better. If they get up often, medium is the safer choice.
Aiming for the middle is what makes the chair work for more than one person. The molded urethane and polypropylene series have a 1-1/2 in thick seat instead of 3 in, and their ranges sit about 1 in lower.
Measure the bench, not the drawing
Work surfaces rarely match their nominal height once a mat, a top or a leveling foot is involved. An anti-fatigue mat can lift the operator an inch. Measure the surface as installed, with the mat in place.
Section Four
Bases, footrings and footrests
Stability, floor space and where the feet go.
Short answer: A wider base is steadier on a tall chair but takes more floor. Any seat above about 22 in needs a footring, and a shared chair needs an adjustable one.
Published base options
| Code |
Base |
Diameter |
Footring |
| S |
Tubular steel |
23 in |
21 in fixed footring included |
| A |
Cast aluminum |
25.6 in |
Optional |
| R |
Reinforced composite |
25.6 in |
Optional |
| W |
Wide aluminum |
28.7 in |
Optional |
- Wider is steadier and takes more floor. The 28.7 in base resists tipping best, which matters on tall chairs. It also sweeps a bigger circle, about 2 ft 5 in across.
- The steel base includes a footring. On the other three it is an added line.
- Composite suits wet areas. Where washdown or chemicals are present, it avoids the finish problems a painted steel base can develop.
Above about 22 in of seat height, most people's feet leave the floor, and unsupported feet are the fastest route to complaints. On a chair shared across a shift, the footring has to move with the seat, so choose an adjustable ring. Where one person at a desk-height bench cannot reach the floor, a BioFit footrest is the cheaper fix. In a static controlled area, use the ESD footrest.
Section Five
Casters or glides
BioFit offers both. Here is how we decide.
Short answer: Use casters when the operator moves along a bench. Use glides on tall chairs, at fixed positions, on mats and on grated floors.
Most configurations offer RC casters, which lock when the seat is empty, HG glides, and RK ESD casters. The guidance below is ours, not a published specification.
Operator moves along a bench or between stations
Casters.
Operator stays at one fixed point
Glides. Nothing rolls away.
Tall chair that the operator climbs onto
Glides, unless movement is truly needed. A tall chair that rolls as someone sits is the main injury risk here.
Floor has drains, grating or thresholds
Glides. Small caster wheels catch.
Anti-fatigue matting at the station
Glides, generally.
ESD-controlled area
ESD casters or conductive glides.
The locking caster is not a brake
The casters lock when the seat is empty, so the chair holds still as someone sits down and rolls freely once they are on it. That is not a substitute for glides where the chair should not move at all.
Section Six
Choosing the series
Seat size, backrest height and material. The rest is common across the platform.
Short answer: Choose a tall backrest for long seated work and a short one for reach and movement. Choose molded seats for wet or dirty areas and a stool with a back for anyone who sits for hours.
Upholstered task series, published sizes
| Series |
Seat |
Backrest |
Suited to |
| Eton |
18.5 by 17 in |
14.5 by 9.5 in |
Tasks needing reach and movement |
| Bridgeport |
18.5 by 16.5 in |
14.5 by 9.5 in |
Everyday industrial use |
| Belize |
18.5 by 16.5 in |
15.5 by 14.5 in |
Long days in a compact footprint |
| Elite |
18.5 by 17 in |
15.5 by 14.5 in |
Long, demanding workdays |
| Amherst |
21 by 19 in |
18 by 19 in |
A roomy seat with lumbar support |
ArmorSeat
Non-porous polypropylene
A wipe-clean surface with nothing to absorb spills.
Stools
Rexford, Regent, Cerex and Aramis
Backless or with a small backrest. Aramis has foot-activated height adjustment for gloved or full hands. See BioFit stools.
Backless is a real choice, not a cheaper one
A backless stool suits short, high-movement work. It is the wrong answer for anyone sitting for hours, because nothing supports the lower back.
Section Seven
Seat controls and arms
What comes standard, and what the upgrades buy.
Short answer: The standard control suits most production seating. Add arms only after checking that the chair still pulls up to the bench with them on.
Published seat control options
| Code |
Control |
What it adds |
| T |
Task Control Soft Touch |
Standard. Pneumatic height, fixed seat tilt, backrest tilt and height |
| FFAC |
Free Float Articulating Control |
Seat and back move with the user |
| EXE |
Executive Tilt Control |
Tilt with tension control, for office work |
| ASC |
Articulating Seat Control |
Separate seat and backrest angle adjustment |
The upgrades earn their cost where one person uses the chair all day, or where the task means leaning forward for long periods.
Arms come as XA, meaning none, unless you specify them. ARS arms adjust for height and width. PSAS arms adjust for height.
Arms and benches conflict
Arms help with keyboard and inspection work and get in the way at a bench, because they stop the chair pulling in and catch on the bench edge. Test one before ordering a run.
Section Eight
Upholstery and seat materials
Choose by what gets spilled on it, not by color.
Short answer: Fabric belongs only in dry areas. Use vinyl where liquids are wiped up, and molded urethane or polypropylene where chemicals, paint or washdown are involved.
Published upholstery and seat materials
| Material |
Specify for |
| Polyester fabric |
Dry offices and labs. Most comfortable, least spill tolerant |
| Vinyl |
Anywhere liquids, oils or frequent wipe-down are involved |
| Vacuum-formed sealed upholstery (VF) |
Resisting fluid getting into the seat. Healthcare and lab |
| Self-skinned urethane, 1-1/2 in seat |
Water, chemicals and paint |
| Polypropylene |
Wipe-clean surfaces and washdown areas |
| Nylon mesh back |
Warm areas and long shifts |
Fabric in a wet or oily area is a false economy
Fabric is the most comfortable option and it absorbs everything. Where there is coolant, oil, solvent or regular spills, choose vinyl or a molded seat. If you supply your own upholstery material, note that BioFit's warranty does not cover it.
Section Nine
Static control seating
What makes a chair ESD-safe, and why standard casters defeat it.
Short answer: An ESD chair needs an unbroken conductive path from the person to the floor. Order the K version with ESD casters or glides, and replace worn casters with ESD casters only.
An ESD chair is not a normal chair with special fabric. Every joint between the person and the floor has to conduct. BioFit's static control chairs address each link:
Published static control construction
| Element |
What is published |
| Height mechanism |
A spring-loaded contact in the pneumatic cylinder keeps the top of the chair grounded to the base |
| Seat |
A carbon-impregnated strip inside, and a conductive covering on the seat bottom that touches the metal frame |
| Backrest |
A conductive polypropylene rear panel |
| Floor contact |
Conductive casters or glides, plus a drag chain |
| Upholstery |
Conductive cloth or static-dissipative vinyl |
The mistake that defeats the whole chair
Ordering an ESD chair with standard casters, or replacing worn ESD casters with standard ones later, breaks the path to the floor. The chair looks the same and nothing warns anyone. Write ESD casters into your spares procedure.
BioFit publishes that its static control seating is tested to ANSI/ESD STM12.1 and is meant to support an ANSI/ESD S20.20 program. The chair is one qualified piece of that program. The floor, the footwear, the wrist strap and your checks are the rest. BioFit's product data does not list resistance values, so if your program needs them for incoming inspection, ask for them before you order.
Section Ten
Cleanroom and harsh environment seating
Ordered by ISO class or by what the chair has to survive.
Short answer: For a cleanroom, order the suffix that matches the class your room is certified to. For paint, chemicals and washdown, order a molded seat on a composite base.
Cleanroom
BioFit cleanroom chairs and stools use vinyl upholstery and chrome-plated metal parts. The ISO class is part of the model number: IS08 for ISO Class 8 and IS06 for ISO Class 6 are the common stocked versions, under ISO 14644-1. Specify the class your room is certified to, and confirm it on the quote.
Particle and outgassing test data are not in the published product information. If your qualification process needs them, request them from the manufacturer before ordering.
Harsh environment and washdown
Paint, solvent or chemical exposure
Molded self-skinned urethane.
Regular washdown
Molded urethane or polypropylene, on a composite base.
Coolant and oil at a machining station
Molded urethane, or vinyl at the least. Not fabric.
Hygiene-controlled areas
Polypropylene for wipe-clean, or vacuum-formed sealed upholstery where padding is needed.
The trade is padding. Molded seats are 1-1/2 in thick against 3 in for upholstered seats, and they are firmer.
Section Eleven
Heavy capacity, continuous use and warranty
One heavy model, and an unusually long warranty with exclusions worth reading.
Short answer: Standard BioFit task chairs are rated 350 lb with a 13-year warranty. The Intensive Plus is rated 500 lb for 24-hour positions and carries a 5-year warranty.
Intensive Plus, published specification
| Item |
Published |
| Capacity |
500 lb |
| Seat height |
20 to 25 in, one range |
| Seat |
21 by 19 in |
| Backrest |
20 by 23 in |
| Base |
Polished aluminum, 27 in wide |
| Intended use |
Continuous, around-the-clock operation |
Control rooms, dispatch desks and security stations are the case for it even where no user is near 500 lb, because a chair used across three shifts wears three times as fast.
Published BioFit warranty terms
| Item |
Published term |
| Standard warranty |
13 years, normal multishift use |
| Pneumatic cylinders |
Functional lifetime of the chair or stool |
| Intensive Plus |
5 years |
| Customer's own upholstery material |
Not covered |
| Unauthorized repairs or modifications |
Void the warranty |
| Freight |
Not covered |
Check before ordering
Swapping casters for a type BioFit has not approved counts as a modification. That matters most on ESD chairs.
Section Twelve
Common and costly mistakes
What goes wrong on seating orders.
Short answer: The costly ones are not measuring the work surface, forgetting the footring on tall chairs, and putting standard casters on an ESD chair.
- Not measuring the work surface. Seat height comes from it.
- Specifying to the edge of the range. Aim for the middle.
- Ignoring the mat. Measure with the mat in place.
- Forgetting the footring on tall chairs. Above about 22 in, feet do not reach the floor.
- A fixed footring on a shared chair. The footring has to move with the seat.
- Casters where glides belong. Tall chairs, mats, grated floors and fixed positions want glides.
- Fabric in a wet, oily or chemical area.
- Standard casters on an ESD chair. This applies to replacement casters too.
- Treating an ESD chair as ESD compliance. It is one part of a program.
- Adding arms without checking bench clearance.
- A backless stool for all-day seated work.
Section Thirteen
Frequently asked questions
The questions that come up most often on seating quotes.
What seat height do I need for my workbench?
Measure the work surface as installed and subtract 12 in. That is the seat height to aim for. A 36 in bench calls for about 24 in, which is the middle of BioFit's medium height class on a steel base.
How do I read a BioFit model number?
The first two letters are the series, the third letter is the base, then the height class (L, M or H), then mobility (RC casters, HG glides, RK ESD casters), then the seat control, footring and arm codes. The last segment is the finish or environment, such as 06 for black or K for static control.
What is the difference between the L, M and H height classes?
On the steel base, low is 18 to 22 in, medium is 21 to 28 in and high is 25 to 32 in of seat height. BioFit matches low to 29 to 34 in work surfaces, medium to 33 to 40 in, and high to 34 to 44 in.
Should I order casters or glides?
Casters if the operator moves along a bench or between stations. Glides for fixed positions, tall chairs, matted stations and floors with grating or thresholds. In an ESD area, use ESD casters or conductive glides.
What weight capacity do these chairs have?
BioFit task chairs are rated at 350 lb. The Intensive Plus is rated at 500 lb.
What makes a chair ESD-safe?
An unbroken conductive path from the person to the floor: conductive upholstery, a grounded seat and backrest, a height mechanism that stays grounded, and conductive casters or glides with a drag chain.
Does an ESD chair make my area S20.20 compliant?
No. BioFit static control seating is tested to ANSI/ESD STM12.1 and is meant to support an ANSI/ESD S20.20 program. The chair is one qualified piece. The floor, footwear and your checks are the rest.
What ISO cleanroom classes are available?
The common stocked versions are ISO Class 8 (IS08) and ISO Class 6 (IS06). Specify the class your room is certified to and confirm it on the quote.
Which chair works in a paint shop or washdown area?
The UniqueU series in molded self-skinned urethane resists water, chemicals and paint. For washdown, pair a molded seat with a composite base.
How long is the warranty?
BioFit publishes 13 years against mechanical or structural failure under normal multishift use, with pneumatic cylinders covered for the functional lifetime of the chair. The Intensive Plus carries 5 years. Customer-supplied upholstery and freight are not covered.
Do I need arms?
Arms help with sustained keyboard and inspection work. At a bench they can stop the chair pulling in. Test one chair with arms at your bench before ordering a run.
Section Fourteen
Quick-reference tables
Everything above, condensed.
Seat height by class and base, 3 in upholstered series
| Class |
S base |
A, R, W bases |
Work surface |
| L |
18 to 22 in |
17 to 22 in |
29 to 34 in |
| M |
21 to 28 in |
19 to 26 in |
33 to 40 in |
| H |
25 to 32 in |
22 to 32 in |
34 to 44 in |
Matching seating to conditions
| Environment |
Specify |
Listing |
| Office, dry lab |
Fabric, low class |
Multipurpose chairs |
| General production bench |
Vinyl, medium or high class with a footring |
Multipurpose chairs |
| Coolant, oil, chemicals, paint |
Molded urethane, composite base |
Harsh environment chairs |
| Electronics, static sensitive |
Static control version, K suffix, ESD casters or glides |
Static control chairs |
| Cleanroom |
Cleanroom version matched to the room's ISO class |
Cleanroom chairs |
| 24-hour position or over 350 lb |
Intensive Plus |
Heavy-capacity chair |
| Short tasks, constant turning |
Stool |
Stools |
Specify-it checklist
1. Work surface height, as installed
Measure it, mat included. Subtract 12 in.
2. Which height class centers on that?
L, M or H.
3. Does the operator move?
Casters if yes, glides if no.
4. Seat height above 22 in?
Add a footring. Adjustable if the chair is shared.
5. How long do they sit?
All day needs a backrest.
6. What gets spilled on it?
Fabric only where dry.
7. Static sensitive area?
K suffix and ESD casters or glides.
8. Cleanroom certified to what class?
Match the suffix to the room.
9. Arms needed, and do they clear the bench?
Test one first.
10. Around-the-clock position or over 350 lb?
Intensive Plus.
About the author. Tom McGovern has worked in the industrial material handling industry since 1981, bringing over 45 years of hands-on experience helping businesses select the right equipment for their applications. His expertise includes specifying and quoting BioFit multipurpose chairs, static control chairs, cleanroom chairs and stools.
Questions about this guide? Call 866-333-0728 to speak with an experienced material handling specialist.