Industrial Equipment Experts Since 1980 | Mon–Fri, 7 AM–6 PM ET
No bots. Real experts. 866-333-0728
Get a Fast Quote
Get a Fast Quote

CustomMHS Buyer's Guide

Containers, Totes & Trays

Divider boxes, straight wall totes, stack and nest containers, ESD totes and trays. What separates them, the stack-versus-nest math, and how to size for your pallet, your conveyor and your washer.

Covers: LEWISBins · Buckhorn · Quantum · Akro-Mils · Kadon · MFG · Monoflo · Orbis · Jesco · Metro Questions: 866-333-0728 Written and reviewed by: Tom McGovern · November 2026
Section One

The question that organizes this entire category

Dozens of products, one decision underneath almost all of them: what happens to the container when it is empty?

Quick answers
  • Stack-only totes carry the most and hold the most. Nest-only totes store smallest when empty. Stack and nest totes do both when you turn them 180 degrees.
  • Nest ratio tells you how much space empties take. At 4.0:1, 400 empty totes store in the space of 100.
  • Most plastic totes we list are rated to about 120°F. For heat, fiberglass composite is rated from -60°F to 250°F.
  • Size the tote to the inside bottom dimension, not the outside top. On a tapered tote the two can differ by more than 3 inches.

A tote spends its life in two states. Full, when it needs to stack so you can build a stable column on a pallet or a shelf. Empty, when it takes up floor space and trailer space and earns nothing.

Those two states pull the design in opposite directions. A tote that stacks well has a rim and base that lock together, so an empty one takes as much room as a full one. A tote that nests has tapered walls, so a full one wants to slide down into the one below it.

Every product in this category is a different answer to that tension:

Answer one

Stack only

Built for load and rigidity. Empties take full space. Right when containers stay loaded, stay on site, or carry serious weight.

Answer two

Nest only

Built for empty storage. You cannot build a stable loaded column. Right when containers are mostly empty, or ride a conveyor instead of a pallet.

Answer three

Stack and nest

Both, by turning the container 180 degrees. Costs a little interior volume for the same footprint. Right for most closed loops.

How to use this guide

Start with section two if you are choosing between styles. Skip to ESD if you handle electronics, sizing if you already know the style, or the spec table if you only need numbers.

Please read this part

This guide is educational and reflects the opinion and general experience of CustomMHS as an equipment distributor. Sizes, load ratings, nest ratios and temperature limits are the manufacturers' published figures and can change. Confirm the current data sheet for your exact model before you order.

Section Two

Stack, nest, or both: the math

This decision is usually made on instinct. It should be made on how many of your containers sit empty.

Short answer: If most of your totes are loaded most of the time, buy stack-only or straight wall. If many sit empty or ride back on a truck, buy stack and nest and compare nest ratios.

How stack and nest works

A stack and nest tote has tapered sidewalls and a rim that is different on each end. Set one on another facing the same way and it nests down inside. Turn it 180 degrees and the rims engage, so it stacks. One container, two behaviors, decided by which way the operator turns it.

That is also how it fails. If your people do not turn the container, they do not get a stack, and a column of half-nested loaded totes is unstable. It takes thirty seconds to train, and it has to be trained.

Nest ratio is the number to compare

Manufacturers publish a nest ratio: how many nested empties fit in the height of one stacked container. The LEWISBins Polylewton SN3022-6 has a published nest ratio of 4.0:1. The Buckhorn AR24201202 attached lid container is published at 5.6:1.

Worked example: 400 empty totes, in feet and inches
  • The tote: SN3022-6, 6.1 in high, nest ratio 4.0:1.
  • Stacked: ten empties make a column 61 in tall (5 ft 1 in). 400 empties need 40 columns.
  • Nested: at 4.0:1 the same 61 in holds about 40 empties. 400 empties need about 10 columns.
  • Result: 30 floor or pallet positions recovered. At a 2.5:1 ratio the same 400 empties would need 16 columns instead of 10.

Where each style wins

Stack only: containers stay loaded, stay on site, or carry heavy loads
The most rigidity and load rating for the footprint, and straight walls give the most interior volume. No rotation to train. Empties cost you full space.
Nest only: containers are empty more often than full
The best empty density. Common on conveyor and tray work where containers never stack loaded. Needs shelving or a conveyor, not a pallet stack.
Stack and nest: a closed loop with a real return leg
The default for most operations. Full totes stack on the outbound pallet and empties nest on the return. Requires the 180 degree turn.
Cross stack: you need to reach the contents mid-column
Stack loaded tubs at 90 degrees to each other so the one below stays reachable, and nest them when empty.
Attached lid: contents must stay secure and clean in transit
The hinged lid cannot be lost, and many models nest with the lids open.
Section Three

The container types

What each one is for, and the spec that matters most on each.

Short answer: Divider boxes are for kitting, straight wall totes for pallet cube, stack and nest for return loops, attached lid for shipping, fiberglass for heat and load, and trays and wire baskets for conveyors and washers.

Divider box containers

A container with slots molded into the walls so dividers drop in and create compartments. This is the kitting workhorse: one container carries every component for one assembly, separated so nothing mixes.

The spec that matters is divider spacing, because it decides how finely you can subdivide. On the divider boxes we list, LEWISBins slots are on 1.25 in centers, and Akro-Grid and Quantum ESD boxes use 1-1/8 in intervals. Footprints are 10-7/8 in × 8-1/4 in, 16-1/2 in × 10-7/8 in and 22-1/2 in × 17-1/2 in, in depths from 2-1/2 in to 12 in.

Straight wall containers

Vertical interior walls with no taper. That gives the most interior volume for a footprint and the most usable cube on a pallet. The trade is empty storage: straight wall means no nesting.

Straight wall totes are the standard for automotive returnable programs, where containers are sized to tile a 48 in × 45 in pallet. See straight wall containers from Quantum, Monoflo, Akro-Mils, Buckhorn and Orbis.

Stack and nest containers

Covered in section two. Compare nest ratio first, then load rating, then vented or solid. Vented walls let air and water through, which matters for wet parts and wash-line output. Solid walls hold small parts, keep dust out and contain liquids. See stack and nest containers and Kadon heavy duty solid and vented totes, which are listed at 150 to 200 lb.

Stack-only and nest-only fiberglass containers

Where load and heat exceed what plastic will take. We list MFG stack-only fiberglass containers in more than 40 sizes, plus 24 conductive sizes, and MFG nest-only containers. Section four has the temperature and chemical figures.

Attached lid containers

A hinged lid molded onto the container, so it cannot be lost or mismatched. The right answer whenever contents travel between buildings or need to stay clean and secure.

The Buckhorn AR24201202 is a good example. It measures 24 in × 19-1/2 in × 12.6 in outside, holds 2.3 cubic feet and 80 lb, weighs 8.3 lb empty, and has a solid textured bottom. See all attached lid containers.

Cross stack tubs

Tubs that stack at 90 degrees to one another when full, so the tub below stays reachable, and nest when empty. Quantum cross stack tubs come in five models from 17-1/4 in × 11 in × 8 in up to 25-1/8 in × 16 in × 8-1/2 in. They hold 100 lb, are molded from FDA and USDA approved polypropylene, and have drain holes in the bottom.

Trays, wire baskets and part wash containers

Conveyor, assembly and ventilation trays are shallow trays built to move, not to sit in storage. A tray that warps jams a conveyor, so holding its shape is the whole job. Ventilation and drying trays add airflow.

Wire baskets give the most airflow, drainage and visibility. See Quantum modular stacking wire baskets and Jesco heavy duty wire baskets. For the washer itself, use part wash containers and baskets made for it.

Container style at a glance
Style Stacks loaded Empty density Interior volume Best for
Divider box Yes Low Good Kitting, multi-part assembly
Straight wall Yes Low Best Returnable programs, pallet cube
Stack and nest Yes, turned 180 degrees High Good Closed loops with a return leg
Nest only No Best Moderate Mostly-empty fleets, conveyors
Stack-only fiberglass Yes Low Good Heat, heavy loads, harsh chemicals
Attached lid Yes High, lids open Good Transit and security
Cross stack tub Yes, at 90 degrees High Good Mid-column access, food handling
Trays Varies High Low by design Conveyors, drying, assembly flow
Wire basket Yes Varies Good Washing, draining, full visibility
Section Four

Materials, and the temperature trap

The most common specification error in this category is assuming a tote handles the same temperatures a parts bin does.

Short answer: Most plastic totes are rated to about 120°F, so they are not for hot wash cycles or hot parts. Fiberglass composite is rated to 250°F and is the material for heat.

HDPE: the tote default

Most totes and stack and nest containers are high-density polyethylene. It is tough, impact resistant, will not rust, and is easy to clean.

Here is the trap. Buckhorn publishes -20°F to 120°F for its attached lid container, and most plastic totes we list are rated to about 120°F. Compare that to the polypropylene small parts bins in our Small Parts Bins guide, where Quantum publishes its Ultra bins as autoclavable up to 250°F. These are not interchangeable numbers. A 120°F tote is not going in a hot wash cycle, an autoclave, or under hot parts.

Polypropylene

Common on tubs and bins. Quantum cross stack tubs are polypropylene, FDA and USDA approved. Check the published temperature limit for the exact model.

Fiberglass composite: for heat and heavy loads

Glass-reinforced composite is a different class of material. MFG publishes continuous use from -60°F to 250°F, with resistance to mild acids and alkaline solutions within a pH of 3.0 to 10.0. On our stack and nest listing, MFG fiberglass containers carry up to 500 lb.

It costs more than a plastic tote. It earns that in heat treat, machining with hot chips, parts washing at temperature, and automated storage systems and robotic cells where the container has to stay the same size for years.

Steel wire

The most airflow and drainage, and full visibility. Match the finish to your wash chemistry and corrosion exposure.

Published material figures
Material Published temperature Relative cost Choose it when
HDPE About 120°F maximum on most totes. Buckhorn attached lid: -20°F to 120°F $ General totes, returnable programs
Polypropylene See the data sheet for the model $ Tubs, bins, FDA and USDA food handling
Fiberglass composite MFG: -60°F to 250°F $$$ Heat, heavy loads, automation, long service life
Conductive and ESD See the data sheet for the model $$ Static-sensitive electronics
Steel wire See the data sheet for the model $$ Washing, draining, ventilation, visibility
FDA approval is often color-specific

On the LEWISBins Polylewton line, the blue and gray containers are FDA approved for direct food contact. Compliance can hinge on the color, not just the resin. If you need food-contact approval, confirm the specific color and ask us for documentation before ordering.

Section Five

ESD containers done properly

"ESD" is not one specification. A conductive container and a static dissipative container work in different ways.

Short answer: Ask for the published surface resistance in ohms, find out whether the container is conductive or static dissipative, and match that to your own ESD control program. Do not buy on the color or the word "ESD" alone.

Standard plastic is an insulator. It can build and hold a static charge, and that charge can damage sensitive electronic components. An ESD container gives the charge somewhere to go.

There are two kinds, and the difference matters:

Slower, controlled

Static dissipative

Bleeds charge away gradually. The range commonly used for dissipative materials is a surface resistance from 104 to under 1011 ohms. Akro-Mils publishes its ESD bins in this range.

Faster, must be grounded

Conductive

Lower resistance, so charge moves quickly. A conductive container has to be grounded to do its job. The Quantum ESD divider boxes we list are carbon-filled polypropylene with a published surface resistance below 105 ohms per square, and grounding is required.

What to ask for

Ask the supplier for the published surface resistance in ohms, not the word "ESD," "conductive" or "anti-static," which are used loosely. Then confirm it against your own ESD control program under ANSI/ESD S20.20. Which type is right depends on how sensitive your devices are, and that is a decision for your ESD coordinator, not a catalog page. Black is a convention, not a specification.

The other ESD question: carbon transfer

Some conductive plastics can leave black residue on parts. Akro-Mils states that its ESD material has a very low carbon content and will not leave black residue. If your parts are cosmetic or have connectors, ask about it.

ESD divider boxes and fiberglass

The most useful ESD format for electronics assembly is the divider box, because it combines static control with compartments. See the ESD options on our divider box listing. Where heat is also involved, MFG offers 24 conductive sizes in its stack-only fiberglass line.

Section Six

Sizing, cube and footprint

Three measurements decide whether the order works, and two of them are not on the front of the catalog page.

Short answer: Check your part against the inside bottom and the product clearance, standardize on one footprint, and read both load ratings before you plan a stack.

Tapered totes have four length and width figures

A tapered tote is a different size at the top and the bottom, inside and out. Published figures for the LEWISBins SN3022-6 show it:

LEWISBins SN3022-6, published dimensions in inches
Where Length × width
Outside top 29.6 × 22.4
Outside bottom 28.3 × 21
Inside top 27.6 × 21.4
Inside bottom 26.1 × 20.5
Height 6.1, with 6.0 of product clearance

A rigid item has to clear the inside bottom, which here is 3-1/2 in shorter than the outside top. Sizing off the outside dimension is the classic way to receive a pallet of totes your part will not sit flat in.

Product clearance is the usable interior height once the stacking rim is allowed for. It is always less than the overall height.

One footprint is worth more than any single container

The value of a container fleet builds when everything shares a footprint or a clean multiple of one. Totes that fit the same pallet, the same conveyor and the same rack bay remove a kind of daily friction that is hard to see until it is gone. The automotive convention is the 48 in × 45 in pallet. If you ship automotive, the footprint is likely dictated to you. If you do not, pick a standard anyway and stick to it.

Two load ratings, not one

Reading load ratings, using the SN3022-6 published figures
Rating Figure What it answers
Maximum load per tote 70 lb How much you can put in one container
Bottom container support 300 lb How much the bottom container can carry on top of it
Worked example: how high can you stack?
  • Support divided by load: 300 lb divided by 70 lb is 4.3, so the bottom tote can carry four fully loaded totes above it. That is a five-high stack.
  • Stack height: five totes at 6.1 in each is about 30-1/2 in.
  • Lighter loads go higher: at 35 lb per tote the bottom tote can carry eight above it, a nine-high stack about 55 in (4 ft 7 in) tall.

The rating assumes an even, square stack on a level surface. Also remember the published weight capacity is a structural limit, not a lifting recommendation. If people lift these by hand, size to what a person should carry.

Tare weight matters if you ship. The Buckhorn AR24201202 weighs 8.3 lb empty. On 300 containers that is 2,490 lb of freight on every leg.

Sizing checklist
  1. Measure the largest item in all three dimensions.
  2. Compare it to the inside bottom and the product clearance, not the outside.
  3. Confirm pallet fit and rack bay fit.
  4. Check both load ratings.
  5. Weigh a full load against what a person should lift.
  6. Note the tare weight if you ship these.
  7. Decide on dividers and lids now, since both are model-specific.
Section Seven

Conveyors, washers and automation

If the container touches equipment and not just hands, a few extra specs become mandatory.

Short answer: For conveyors, confirm a textured bottom. For washers, confirm the temperature rating and drainage. For automation, confirm the exact model with your integrator before you buy.

Conveyable bottoms

A container that rides a conveyor needs a bottom made for it. The LEWISBins Polylewton line has a textured bottom for compatibility with conveying equipment, and the Buckhorn AR24201202 has a solid textured bottom. Check it for your model instead of assuming.

Holding shape for automation

Automated storage systems and robotic cells assume the container is the size the drawing says it is, every time, for years. That is the strongest argument for fiberglass composite in automation, and MFG lists its stack-only containers for automated storage systems and robotic cells. Tell the integrator the exact model before you buy, not after.

Wash lines

  • Temperature. Wash cycles run hot. A tote rated to 120°F is not a wash-line container. This is the most common mismatch we see.
  • Drainage. Solid-bottom containers hold water. Vented containers, drain holes or wire baskets solve it. Quantum cross stack tubs have drain holes molded in.
  • Chemistry. MFG fiberglass composite covers a pH of 3.0 to 10.0. For anything more aggressive, check the specific chemical.

Labels, lids and dollies

Label areas and card holders are worth specifying at purchase, because adhesive labels do not last on a fleet that gets washed. Container I.D. placards give you a durable, swappable alternative. Lids, dollies and dividers are model-specific, so order them with the containers.

Section Eight

The returnable packaging calculation

If you are replacing corrugated, the comparison is not sticker price. It is cost per trip.

Short answer: Returnable totes beat corrugated when you control both ends of the loop, get enough trips out of each tote, and keep the return freight low. Nest ratio is what keeps return freight low.

A corrugated box costs a little and is used once. A plastic tote costs more and is used many times. Comparing the two on purchase price always favors corrugated and is always the wrong comparison. The right one:

Cost per trip = (P − S) ÷ T + H + R
P
Purchase price of the container
S
Salvage or recycle value at end of life
T
Realistic number of trips before retirement, including loss and damage
H
Handling per trip: washing, sorting, staging, inspection
R
Return cost per trip: freight on the empty leg
Worked example with made-up numbers
  • Inputs: a $25.00 tote, $1.00 salvage, 60 trips, $0.20 handling and $0.15 return freight per trip.
  • Math: ($25.00 − $1.00) ÷ 60 = $0.40. Add $0.20 and $0.15.
  • Result: $0.75 per trip. If only 30 trips are realistic, the same tote costs $1.15 per trip.

The estimate usually goes wrong on T. Containers get damaged, stay with customers, and disappear at receiving docks. Use a realistic figure or, better, track losses in a pilot before committing to a fleet.

Be honest about the loop

The most common returnable packaging failure is not a bad container. It is a loop nobody owns. Before you buy a fleet, decide who is accountable for containers coming back, how you will count them, and what happens when a customer keeps them. If you cannot answer those three questions, start with a pilot on one lane.

Section Nine

Choosing by application

Find the row that matches your situation.

Short answer: Start with whether the container returns empty, then the temperature it will see, then what it rides on.

Kitting components for assembly
Divider boxes, so you can change the compartments as the kit changes.
Closed-loop shipping between your own plants
Stack and nest, chosen on nest ratio. The return leg is where the savings are. Make sure the 180 degree turn gets trained.
Automotive returnable program
Straight wall totes sized to the 48 in × 45 in pallet, with a conveyable bottom and label areas.
Electronics assembly or board handling
ESD divider boxes with a published surface resistance that matches your ESD control program. Do not buy on the word "conductive" alone.
Hot parts, heat treat, machining with hot chips
Fiberglass composite, published at -60°F to 250°F. A tote rated to about 120°F is not a candidate.
Parts washing and washdown
Part wash containers, wire baskets, or vented containers with drainage. Check the temperature rating against your actual wash cycle.
Food handling or food contact
FDA-approved resin, with the color confirmed: blue or gray on the LEWISBins Polylewton line, or Quantum cross stack tubs in FDA and USDA approved polypropylene.
Shipping to a customer or across sites
Attached lid containers. The lid cannot be lost, and many models still nest with the lids open.
Feeding an automated storage system or robotic cell
Fiberglass composite where the budget allows. Confirm the exact model with your integrator before ordering.
Parts moving continuously on a conveyor
Conveyor and assembly trays, or totes with a textured bottom.
Drying, curing or cooling
Ventilation trays, drying trays or vented containers. Airflow is the whole specification.
Need to reach the container below without unstacking
Cross stack tubs, stacked at 90 degrees. They hold 100 lb and nest when empty.
Heavy, dense parts
Check the bottom container support rating, not just the load per tote. Look at Kadon heavy duty totes at 150 to 200 lb or MFG fiberglass at up to 500 lb.
Section Ten

Common and costly mistakes

These come up on quote calls repeatedly. All are cheap to avoid beforehand.

Short answer: The costly ones are assuming a tote takes bin temperatures, sizing from outside dimensions, and reading only one of the two load ratings.

Assuming a tote handles bin temperatures

The biggest one. Some polypropylene parts bins are autoclavable up to 250°F. Most plastic totes are rated to about 120°F. Different products, very different limits.

Sizing off outside dimensions

Your part has to clear the inside bottom, which can be several inches smaller than the outside top.

Ignoring product clearance

Usable interior height is less than overall height once the stacking rim is allowed for.

Reading only one load rating

Load per tote tells you what goes in. Bottom container support tells you how high you can stack.

Buying stack and nest, then not training the turn

The feature only works if operators turn the container 180 degrees. Untrained, you get unstable half-nested columns.

Treating "ESD" as a single specification

Conductive and static dissipative are different. Ask for the published surface resistance and check it against your ESD program.

Assuming FDA approval covers the whole line

It is often color-specific. Confirm the color.

Mixing footprints across a fleet

Containers that do not share a footprint waste pallet space and slow every handling step.

Forgetting the empty leg

Return freight on empties that do not nest is a cost that never shows up in the purchase decision.

Ordering containers without dividers, lids or dollies

All are model-specific. Adding them later means a second freight bill.

Section Eleven

Cleaning and service life

Containers in a returnable loop are cleaned constantly. A few habits protect the investment.

Short answer: Wash within the temperature rating, drain fully, keep loads under the rating, stack square, and pull cracked containers out of service.

  • Wash within the temperature rating. In our experience, washing above the rated temperature is the most common cause of early tote failure. Warping starts small and ends with containers that no longer stack or nest.
  • Match chemistry to material. MFG fiberglass composite covers a pH of 3.0 to 10.0. For aggressive cleaners, check the specific chemical against the manufacturer's data.
  • Drain fully. Solid-bottom containers hold water in the corners. Turn them over to dry, or specify drain holes or vented walls.
  • Do not exceed load ratings. A container held over its rating can deform for good even without cracking, and a deformed rim weakens the whole stack above it.
  • Stack square and on level ground. Ratings assume an even vertical load.
  • Inspect rims and bases. Whitening and hairline cracks at the stacking rim and base are the early warning.
  • Retire, do not repair. A cracked container in a stack is a hazard to everything above it.
  • Standardize on a few models. Then a damaged container gets replaced from stock the same day.
Section Twelve

Frequently asked questions

What comes up most often on quote calls.

What is the difference between stack and nest, stack only, and nest only?

Stack only containers have straight or nearly straight walls and rigid rims. They give the most volume and load, but empties take full space. Nest only containers taper so empties drop into each other, but they cannot build a stable loaded column. Stack and nest containers do both: turned 180 degrees they stack, and facing the same way they nest.

What is a nest ratio and why does it matter?

It is how many nested empty containers fit in the height of one stacked container. A published 4.0:1 ratio means 400 empties store in the space of 100. It turns directly into floor space and into trailer space on the return leg.

Can I put a plastic tote through a hot wash cycle?

Check the rating first. Most plastic totes we list are rated to about 120°F, and Buckhorn publishes -20°F to 120°F for its attached lid container. That does not cover a hot wash. MFG fiberglass composite is published at -60°F to 250°F.

Is a conductive ESD container better than a static dissipative one?

Neither is better in every case. A static dissipative container bleeds charge away gradually, and a conductive container moves it quickly and must be grounded. Ask for the published surface resistance in ohms and match it to your ESD control program under ANSI/ESD S20.20.

Why do totes list four different dimensions?

Because tapered walls make the top and bottom different sizes, so there is an outside top, outside bottom, inside top and inside bottom. Your part has to fit the inside bottom. Also check product clearance, the usable height under the stacking rim.

What is the difference between the two weight ratings?

Maximum load per tote is how much goes inside one container. Bottom container support is how much the bottom container can carry stacked on top of it, and that limits your stack height. On the LEWISBins SN3022-6, 70 lb per tote and 300 lb of support means four loaded totes above the bottom one.

Are returnable containers cheaper than corrugated?

It depends on trips and loop control, not purchase price. Compare cost per trip: purchase price less salvage, divided by realistic trips, plus handling and return freight per trip. Returnables win with a controlled loop and enough trips. They lose when containers do not come back.

Vented or solid?

Vented for wet parts, wash-line output and anything that would trap moisture. Solid to hold small parts, keep dust out and contain liquids.

Do all containers work on a conveyor?

No. Look for a textured bottom made for conveying equipment, and check it for your model. For automated systems, confirm the exact model with your integrator before ordering.

Can I use these containers for food contact?

Only if the specific resin and color are approved. On the LEWISBins Polylewton line, blue and gray are FDA approved for direct food contact. Quantum cross stack tubs are FDA and USDA approved polypropylene. Confirm the exact model and color and ask us for documentation.

How many containers do I need?

Count containers in every state, not just the ones in use: loaded and staged, in transit, empty and waiting to return, in the wash, and in reserve. A closed loop needs enough to cover the full cycle plus a buffer for damage and loss.

Should I standardize on one footprint?

Yes, wherever you can. Containers that share a footprint fit the same pallet, the same conveyor and the same rack bay. If you ship automotive, the 48 in × 45 in pallet is likely dictated to you.

Section Thirteen

Quick-reference spec table

Published figures for products referenced in this guide. Confirm the exact model before ordering, since specs vary within every line.

Published specifications
Product Size Material Published capacity Notes
LEWISBins Polylewton SN3022-6 29.6 in × 22.4 in × 6.1 in outside top. 6.0 in product clearance HDPE 70 lb per tote, 300 lb bottom support, 2.1 cu ft Nest ratio 4.0:1. 4.8 lb empty. Blue and gray FDA approved. Textured bottom.
Buckhorn AR24201202 attached lid 24 in × 19-1/2 in × 12.6 in outside. 20-1/2 in × 16.6 in × 10.8 in inside bottom Plastic 80 lb, 2.3 cu ft -20°F to 120°F. 8.3 lb empty. Solid textured bottom. Gray.
Quantum cross stack tubs Five models, 17-1/4 in × 11 in × 8 in up to 25-1/8 in × 16 in × 8-1/2 in Polypropylene, FDA and USDA approved 100 lb Drain holes. Gray, blue, white.
Divider box containers 10-7/8 in × 8-1/4 in up to 22-1/2 in × 17-1/2 in, 2-1/2 in to 12 in deep HDPE. Quantum ESD: carbon-filled polypropylene See listing LEWISBins 1.25 in divider centers. Akro-Grid and Quantum ESD 1-1/8 in.
MFG stack-only fiberglass More than 40 sizes, plus 24 conductive sizes Glass-reinforced composite See listing -60°F to 250°F. pH 3.0 to 10.0.
Kadon heavy duty totes See listing Plastic, solid or vented 150 to 200 lb Heavy duty daily use.
Product families in this category
Family Brands we list Primary job
Divider box containers LEWISBins, Akro-Mils, Quantum Kitting and component separation
Straight wall containers Quantum, Monoflo, Akro-Mils, Buckhorn, Orbis Pallet cube, returnable programs
Attached lid containers Buckhorn, Akro-Mils, Quantum, Monoflo, LEWISBins Secure transit
Stack and nest containers LEWISBins, Akro-Mils, Kadon, Quantum, Orbis, MFG Closed loops with a return leg
Stack-only fiberglass MFG Heat, heavy loads, automation
Nest-only containers MFG Mostly-empty fleets
Cross stack tubs Quantum Mid-column access
Conveyor, assembly and ventilation trays MFG Continuous movement, drying
Drying trays Metro Airflow drying
Wire baskets Quantum, Jesco Washing, draining, visibility
Part wash containers and baskets MFG Cleaning and washdown
Container I.D. placards See listing Identification across the fleet
Before you order

"See listing" and "See the data sheet" mark figures we did not find published on the sources reviewed for this guide. For load ratings, nest ratios, temperature limits, ESD surface resistance or FDA documentation on a specific model and color, call and we will pull the data sheet.

About the author. Tom McGovern has worked in the industrial material handling industry since 1981, bringing over 45 years of hands-on experience helping businesses select the right equipment for their applications. His expertise includes specifying and quoting divider boxes, straight wall totes, stack and nest containers and attached lid containers.

Questions about this guide? Call 866-333-0728 to speak with an experienced material handling specialist.

Ready for a quote?

Send us these details and a material handling specialist will reply, typically within one business day.

  • Dimensions
    Size of the load and the space it goes in
  • Load
    Weight per item, shelf or level
  • Quantity
    How many units you need
  • Delivery ZIP code
    For freight pricing
  • Drawing
    A sketch, photo or spec sheet, if you have one
Get a Fast Quote Call 866-333-0728

Tell us the part, the loop and the pallet

Give us the item dimensions, how many containers sit empty at peak, and whether they touch a conveyor or a washer. We will spec the fleet. Quotes are reviewed by material handling specialists, typically within one business day.

866-333-0728

Browse containers, totes & trays at custommhs.com

No bots. No guesswork. Real experts.

Sources

LEWISBins and ORBIS published product data · Buckhorn published product data · Quantum Storage Systems published product data · MFG Tray published product data · Akro-Mils published product data · CustomMHS product listings.

Disclaimer. This guide is educational content and reflects the opinion and general experience of CustomMHS. Sizes, load ratings, nest ratios and temperature limits are manufacturer-published figures and are subject to change. Confirm critical specifications against the current data sheet for your exact model and color before ordering. ESD selection should be verified against your own ESD control program. Reviewed November 2026.