Industrial Equipment Experts Since 1980 | Mon–Fri, 7 AM–6 PM ET
No bots. Real experts. 866-333-0728
Get a Fast Quote
Get a Fast Quote

CustomMHS Buyer's Guide

Dock Equipment

Three products bridge the gap between a dock and a trailer, and they are not interchangeable. One is rated for forklifts, one is not, and one is bolted to the dock face.

Covers: Vestil dockboards, dock plates, edge-of-dock levelers and gates · Handle-It stretch wrappers Questions: 866-333-0728 Written and reviewed by: Tom McGovern · November 2026
Section One

What a dock needs

Three products bridge the gap between a dock and a trailer, and they are not interchangeable.

Quick answers
  • If a forklift crosses the gap, use a dockboard or an edge-of-dock leveler. Dock plates are published as not intended for fork trucks.
  • Size capacity for the forklift plus its load plus the operator. A 9,000 lb truck carrying a 3,000 lb pallet is more than a 12,000 lb crossing.
  • OSHA 1910.26 requires dockboards to carry the load, keep vehicles from running off the edge, stay in position, and have the trailer held with wheel chocks or similar.
  • Match dockboard length to the height difference: 36 in for 5 in, 48 in for 7 in, 60 in for 10 in and 72 in for 12 in.

A loading dock packs more risk into a small area than almost anywhere else in a building. Trailers shift, forklifts cross a gap, and people walk through the same lanes as powered equipment.

This guide covers what we list: edge-of-dock levelers, steel and aluminum dockboards, aluminum dock plates, dock gates, trailer stabilizing jacks and stretch wrap machines.

Wheel chocks are part of the job

OSHA requires measures to stop the truck or trailer moving while a dockboard is in use. Chocks do not come with a dockboard. Whatever you use, have it on hand before the dock goes into service. Vehicle restraints, pit levelers, dock seals and dock lights are also separate purchases.

Related guides

Guard rail and bollards around the dock are in the Barriers and Machine Guarding guide. Driver cages are in the Wire Partitions and Security Cages guide.

Please read this part

This guide is educational and reflects the opinion and general experience of CustomMHS as an equipment distributor. It is not a compliance assessment or engineering advice. OSHA does not certify or approve products. Compliance depends on how equipment is selected, installed and used at your site. Capacities and sizes are the manufacturers' published figures and can change, so confirm them on the listing or your quote.

Section Two

Bridging the gap: three products, one decision

The most important section in this guide.

Short answer: What crosses the gap decides the product. Forklifts need a dockboard or an edge-of-dock leveler. Hand trucks and carts can use a dock plate.

The three gap-bridging products, as published
Dockboard Dock plate Edge-of-dock leveler
Forklift rated Yes No. Published as not intended for fork trucks Yes
Run-off protection Welded safety curbs None published None published. Discuss with your safety officer
Portable Yes, with locking legs Yes, with legs and handles No. Attached to the dock face
Capacities listed 5,000 to 25,000 lb 1,400 to 11,900 lb 6,000 to 30,000 lb
Typical traffic Forklifts and pallet trucks Hand trucks, carts, foot traffic Forklifts, all day
The distinction that gets people hurt

A dock plate is not a small dockboard. The published description says these dock plates are not intended for use with fork trucks. They have no safety curbs, and their capacities are for manual traffic. A high number on a dock plate is not a forklift rating.

Forklift crosses the gap
Dockboard or edge-of-dock leveler.
Hand trucks and carts only
Dock plate.
Same trailer height every day, high volume
Edge-of-dock leveler. It is always there.
Trailer heights vary widely
Dockboard. It covers a range of heights and moves between doors.
Several doors, bridging now and then
One or two dockboards shared between doors.
Dock is below 48 in (4 ft) high
Edge-of-dock levelers are published for docks at least 48 in high. Below that, ask us.
Section Three

What OSHA 1910.26 requires

Five short paragraphs that govern every dockboard purchase.

Short answer: A dockboard must carry the maximum intended load, have run-off protection if put in service since January 17, 2017, be secured in place, be used with the vehicle held still, and have handholds if portable.

29 CFR 1910.26, Dockboards
Paragraph Requirement What it means when you buy
(a) Dockboards support the maximum intended load Capacity must cover the forklift, its load and the operator
(b)(1) Dockboards put into service on or after January 17, 2017 are built to keep transfer vehicles from running off the edge This is what welded safety curbs are for
(b)(2) Boards without run-off protection may be used where the employer shows there is no run-off hazard The exception, which you would have to demonstrate
(c) Portable dockboards are anchored or held so they cannot move out of a safe position Locking legs. Check they engage on your dock edge
(d) Measures such as wheel chocks or sand shoes keep the transport vehicle from moving while employees are on the dockboard Not supplied with the board. Have them on hand
(e) Portable dockboards have handholds or other means for safe handling Handles, or legs placed for fork truck pickup
On "manufactured in compliance with OSHA"

You will see that phrase on product listings across this industry. OSHA does not certify or approve products. Whether your installation complies depends on use: whether the capacity covers your real load, whether the vehicle is held, and whether the board is secured.

Section Four

Reading the model numbers

Four Vestil families, four patterns.

Short answer: Vestil part numbers carry the capacity and the size. On levelers the first two digits are thousands of pounds and the last two are the width in inches.

PE - 30 72
PE
Power electric. FM is mechanical and PP is hydraulic hand pump
30
Capacity in thousands of pounds: 30,000 lb
72
Usable width in inches: 72 in, or 6 ft
The four patterns
Family Pattern Example
Edge-of-dock levelers FM, PP or PE, then capacity in thousands, then width FM-2078 is mechanical, 20,000 lb, 78 in wide
Steel dockboards TS, capacity in thousands, width, length TS-25-7248 is 25,000 lb, 72 in wide by 48 in long
Aluminum dockboards BTA, capacity in five digits, width, length BTA-20007236 is 20,000 lb, 72 in by 36 in
Aluminum dock plates E or EH, width, length E-4836 is 3/8 in plate, 48 in by 36 in. EH-4836 is 1/2 in plate

On dock plates the letter is the thickness, and there is no capacity in the number. A 48 in by 24 in plate is published at 5,200 lb as an E and 8,200 lb as an EH. Gates use short prefixes: SDG swivel dock gate, SSG swing gate, SLG lift gate. Always confirm the brand along with the part number.

Section Five

Sizing the capacity

Where undersizing happens, and it is not where people look.

Short answer: Add the forklift's weight from its data plate, the heaviest load and the operator. Buy a board rated above that total.

Maximum intended load = forklift weight + load weight + operator
Forklift
The truck's own weight, from its data plate. Often more than the load it carries
Load
The heaviest pallet that will cross, not the average
Operator
Included in the total
Worked example
  • Truck: 9,000 lb on the data plate.
  • Load: 3,000 lb pallet.
  • Operator: 250 lb.
  • Total: 9,000 + 3,000 + 250 = 12,250 lb. A 10,000 lb board is too small. Buy the next rating above the total, such as 15,000 lb.
Capacities and sizes listed
Family Capacities Widths Lengths
Edge-of-dock levelers 6,000 to 30,000 lb 48, 66, 72, 78 in Fixed to the dock face
Steel dockboards 10,000 to 25,000 lb 60, 72, 84 in 36 to 72 in
Aluminum dockboards 5,000 to 20,000 lb 60, 72, 78, 84 in 30 to 84 in
Aluminum dock plates 1,400 to 11,900 lb 30, 36, 48, 60, 72 in 24 to 60 in

Not every capacity comes in every size, so check the exact combination.

Length sets the height difference

Steel dockboard length and published height difference
Board length Height difference
36 in (3 ft) 5 in
48 in (4 ft) 7 in
60 in (5 ft) 10 in
72 in (6 ft) 12 in

Measure the difference between your dock and the trailer beds you receive at the extremes, not the average. If your dock is 48 in high and the lowest trailer bed is 40 in, the difference is 8 in, so you need the 60 in board, not the 48 in.

Section Six

Edge-of-dock levelers

Permanent, always there, and a way to level a dock without cutting a pit.

Short answer: Choose a leveler for a door that sees the same trailer height on a schedule. Pick electric for busy doors and mechanical for light use.

FM

Mechanical

The operator works a handle to raise the leveler and set the lip on the truck bed. For lower volume doors and tight budgets.

PP

Hydraulic hand pump

A hand pump lifts the leveler and extends the lip. For doors with no convenient power.

PE

Electric hydraulic

Back the truck in, then push and hold the button. Standard 115V single phase. For high volume doors.

Choose by traffic, not price. A mechanical leveler on a door running fifty trailers a day is a leveler people stop using properly.

  • Service range is published as 5 in above and below dock height on the model we checked.
  • Overall width is more than usable width. The 66 in model we checked is 93 in (7 ft 9 in) overall. Check it against your door opening.
  • Dock bumpers are included.
  • The lip retracts when the trailer leaves.
  • The dock should be at least 48 in high, with a steel dock edge or approach ramp.

Lip length and unit weight are not on the listings. If they matter to you, ask us for them in writing.

Section Seven

Steel or aluminum dockboards

The same job in two materials.

Short answer: Aluminum is lighter to move and comes longer. Steel carries more and takes more abuse.

Steel against aluminum, as listed
Steel Aluminum
Prefix TS BTA
Capacities 10,000 to 25,000 lb 5,000 to 20,000 lb
Widths 60, 72, 84 in 60, 72, 78, 84 in
Lengths 36 to 72 in 30 to 84 in
Deck High strength steel, diamond plate Aluminum
Handling Locking legs and a lever lift for fork truck handling Locking legs placed for fork truck pickup

Both are forklift rated, both have welded safety curbs, and both use locking legs. If the board is moved between doors by hand, you feel the weight every day, so choose aluminum. If it lives at one door under heavy traffic, choose steel.

Section Eight

Dock plates, and where they must not go

A useful product with one hard limit.

Short answer: Dock plates are for hand trucks, carts and foot traffic. Buy the shortest plate that spans the gap, because capacity drops fast as the plate gets longer.

Aluminum dock plates come in two thicknesses, with bolt-on legs and handles on each side. They are not intended for use with fork trucks.

How thickness and length change capacity, published examples
Plate Thickness Capacity
48 in wide by 24 in long 3/8 in (E) 5,200 lb
48 in wide by 24 in long 1/2 in (EH) 8,200 lb
72 in wide by 24 in long 3/8 in (E) 6,500 lb
72 in wide by 24 in long 1/2 in (EH) 11,900 lb
30 in wide by 24 in long 3/8 in (E) 3,000 lb
30 in wide by 48 in long 3/8 in (E) 1,400 lb

Look at the last two rows. Same width, same thickness, twice the length, and less than half the capacity. Measure the gap, add a safe overlap at each end, and buy to that. If you need both length and capacity, choose the 1/2 in plate or a dockboard.

Section Nine

Securing the trailer

Two separate hazards and two separate rules.

Short answer: Chocks or a restraint keep the trailer from rolling away from the dock. Jacks keep an uncoupled trailer from tipping nose-down. You may need both.

29 CFR 1910.178(k)(1)

"The brakes of highway trucks shall be set and wheel chocks placed under the rear wheels to prevent the trucks from rolling while they are boarded with powered industrial trucks."

29 CFR 1910.178(m)(7)

"Brakes shall be set and wheel blocks shall be in place to prevent movement of trucks, trailers, or railroad cars while loading or unloading."

Read with 1910.26(d), the requirement is consistent: hold the vehicle before a truck boards it.

29 CFR 1910.178(k)(3)

"Fixed jacks may be necessary to support a semitrailer and prevent upending during the loading or unloading when the trailer is not coupled to a tractor."

That is what trailer stabilizing jacks are for. Choose a jack by its height range as well as its capacity: measure the underside of the trailers you receive, at their extremes.

A jack is not a restraint

A jack stops the nose of an uncoupled trailer dropping when a forklift drives toward the front. It does not stop the trailer rolling away from the dock.

Section Ten

Gates and the open dock door

An open dock door with no trailer at it is a fall hazard at dock height.

Short answer: Pick the gate by the opening width, how often it is operated, and whether a vehicle could hit it. Check headroom before ordering a lift gate.

Dock gate families we list
Family How it works Sizes listed Notes
Vestil swivel dock gates Swing on bollard pivots 8, 9 and 10 ft, 42 in tall Sold in pairs
Vestil economical safety swing gates Swing, wheel supported 108 and 132 in openings (9 ft and 11 ft) Top rail and mid-rail
Vestil safety lift gate Lifts and folds upward 6, 8 and 10 ft Raised height runs 111 to 159 in
Illinois Engineered folding security gates Folding scissor gate See listing Security for door openings
Check the headroom on lift gates

Raised heights of 111 to 159 in mean 9 ft 3 in to 13 ft 3 in of clear height above the floor. Measure first, especially under a mezzanine or a sprinkler main.

A folding or expanding gate is a reminder to a person on foot. It is not a vehicle barrier. Where a forklift could drive at the opening, add impact protection such as guard rail. For drivers who must wait inside, see the WireCrafters driver cage.

Section Eleven

Stretch wrapping at the dock

The dock is usually where loads get wrapped before shipping.

Short answer: Compare stretch wrappers on how far they stretch the film. A machine with 250 percent pre-stretch uses much less film per pallet than one at 150 percent.

Handle-It stretch wrap machines, as listed
Model Type Published detail
SWM-SA-0800 Semi-automatic 4,400 lb capacity, 86 in (7 ft 2 in) wrap height, 150% stretch
SWM-SA-850PS Semi-automatic, powered pre-stretch 250% pre-stretch, 86 in wrap height
SWM-SA-1200UL Ultra low profile No ramp needed, 250% pre-stretch
SWM-SA-1100AA-C Automatic Attaches, seals and cuts the film automatically
SWM-MR-3000 Mobile Travels around loads too long, heavy or unstable for a turntable

Have your pallets per day, tallest load, heaviest load and whether loads are stable ready when you call. Those decide the type before price does. See Handle-It stretch wrap machines.

Section Twelve

Common and costly mistakes

What goes wrong on dock equipment orders.

Short answer: The dangerous ones are running a forklift over a dock plate, sizing from the pallet weight, and putting a dockboard in service with no wheel chocks.

  • Running a forklift over a dock plate. They are not intended for fork trucks, whatever the number.
  • Sizing capacity from the pallet weight. Add the truck and the operator.
  • Ordering a dockboard with no wheel chocks.
  • Buying a long dock plate for flexibility. Capacity falls with length.
  • Assuming every capacity exists at every size.
  • Measuring the average trailer height. Measure the extremes.
  • Ignoring the overall width of an edge-of-dock leveler.
  • A mechanical leveler on a high-volume door.
  • A lift gate without checking headroom.
  • Confusing a trailer jack with a restraint.
Section Thirteen

Frequently asked questions

The questions that come up most often on dock equipment quotes.

What is the difference between a dockboard and a dock plate?

A dockboard is forklift rated and has welded safety curbs to keep wheels from running off the edge. A dock plate is a flat plate for hand trucks, carts and foot traffic, and is published as not intended for use with fork trucks.

Can I use a dock plate with a forklift if the capacity looks high enough?

No. The published description says the dock plates are not intended for fork trucks. They have no safety curbs and their capacities are for manual traffic.

What capacity dockboard do I need?

Add the forklift's weight from its data plate, the heaviest load and the operator, then buy above that total. A 9,000 lb truck with a 3,000 lb pallet and a 250 lb operator is 12,250 lb.

What does OSHA require for dockboards?

29 CFR 1910.26 requires that dockboards support the maximum intended load, have run-off protection if put into service on or after January 17, 2017, be secured so they cannot move, be used with measures such as wheel chocks that hold the vehicle, and have handholds if portable.

Do I need wheel chocks?

OSHA 1910.178(k)(1) requires brakes set and wheel chocks under the rear wheels of highway trucks while they are boarded with powered industrial trucks, and 1910.26(d) requires measures such as chocks or sand shoes when a dockboard is used.

How do I read a Vestil dock model number?

On edge-of-dock levelers, FM, PP or PE is the actuation, the next two digits are capacity in thousands of pounds, and the last two are the width in inches. PE-3072 is electric, 30,000 lb, 72 in wide. Steel dockboards start with TS and aluminum with BTA.

Steel or aluminum dockboard?

Aluminum is lighter to handle and comes in lengths up to 84 in. Steel carries up to 25,000 lb and takes more abuse. Choose aluminum if people move it, steel if it stays at one busy door.

When should I choose an edge-of-dock leveler?

When one door sees the same trailer height on a regular schedule and the dock is at least 48 in high. It is always in place, with nothing to fetch or store.

Mechanical, hand pump or electric leveler?

Mechanical for low volume, hand pump where there is no power, and electric for high volume doors.

What length dockboard do I need?

On the steel boards, a 36 in board is published for a 5 in height difference, 48 in for 7 in, 60 in for 10 in and 72 in for 12 in. Measure your largest difference.

Do trailer stabilizing jacks replace wheel chocks?

No. Jacks keep an uncoupled trailer from tipping nose-down. Chocks or a restraint keep it from rolling away from the dock.

Section Fourteen

Quick-reference tables

Everything above, condensed.

Choosing the gap bridge
If Buy
A forklift crosses Dockboard or edge-of-dock leveler. Never a dock plate
Hand trucks and carts only Dock plate, the shortest that spans the gap
Same trailer height daily, high volume Edge-of-dock leveler, electric
Trailer heights vary widely Dockboard, length matched to the largest height difference
Board handled by people Aluminum dockboard
Regulations cited in this guide
Requirement Source
Dockboard supports the maximum intended load 29 CFR 1910.26(a)
Run-off protection on dockboards in service since January 17, 2017 1910.26(b)(1)
Portable dockboards secured against movement 1910.26(c)
Wheel chocks or sand shoes to stop vehicle movement 1910.26(d)
Brakes set and chocks under rear wheels when boarded 1910.178(k)(1)
Fixed jacks to prevent upending of an uncoupled semitrailer 1910.178(k)(3)

Specify-it checklist

1. What crosses the gap?
Forklift means dockboard or leveler.
2. Forklift weight from the data plate
Plus the heaviest load, plus the operator.
3. Height difference at the extremes
Sets the dockboard length.
4. Same trailer height every day?
Yes points to a leveler.
5. Door opening width
Check the leveler's overall width.
6. How many trailers a day?
High volume justifies electric.
7. Are chocks or restraints on hand?
Required before a truck boards a trailer.
8. Uncoupled trailers loaded here?
Trailer stabilizing jacks.
9. Open door when no trailer is there?
A gate. Check headroom for lift gates.

About the author. Tom McGovern has worked in the industrial material handling industry since 1981, bringing over 45 years of hands-on experience helping businesses select the right equipment for their applications. His expertise includes specifying and quoting edge-of-dock levelers, steel and aluminum dockboards, dock plates and dock gates.

Questions about this guide? Call 866-333-0728 to speak with an experienced material handling specialist.

Ready for a quote?

Send us these details and a material handling specialist will reply, typically within one business day.

  • Dimensions
    Size of the load and the space it goes in
  • Load
    Weight per item, shelf or level
  • Quantity
    How many units you need
  • Delivery ZIP code
    For freight pricing
  • Drawing
    A sketch, photo or spec sheet, if you have one
Get a Fast Quote Call 866-333-0728

Send us the dock

Tell us the dock height, the highest and lowest trailer beds you receive, what crosses the gap and what it weighs including the truck, how many trailers a day, and the door opening width. We will size the board or the leveler. Quotes are reviewed by material handling specialists, typically within one business day.

866-333-0728

Browse dock equipment

No bots. No guesswork. Real experts.

Sources

OSHA 29 CFR 1910.26 · 29 CFR 1910.178(k) and (m) · Vestil and Handle-It figures as published on CustomMHS product listings.

Disclaimer. This guide is educational content and reflects the opinion and general experience of CustomMHS. It is not a compliance assessment or engineering advice. OSHA does not certify or approve products. Capacity must be determined for your actual crossing load. Wheel chocks or vehicle restraints are required where powered industrial trucks board trailers and are not supplied with the equipment described here. Confirm current specifications on the product listing or quote before ordering. Reviewed November 2026.