Industrial Equipment Experts Since 1980 | Mon–Fri, 7 AM–6 PM ET
No bots. Real experts. 866-333-0728
Get a Fast Quote
Get a Fast Quote

CustomMHS Buyer's Guide

Dock Plate vs. Dockboard: What Is the Difference and Which Do You Need?

They both bridge the gap between the dock and the trailer. One is for hand trucks. The other is for forklifts. Mixing them up is the mistake to avoid.

Written and reviewed by: Tom McGovern, owner of CustomMHSPublished: November 2026Covers: Vestil steel and aluminum dockboards · Vestil aluminum dock platesQuestions: 866-333-0728
Section One

Dock plate or dockboard?

The answer is whatever rolls across it.

Short answer: Use a dock plate for hand trucks, carts and foot traffic. Use a dockboard for forklifts and pallet trucks. A forklift crossing requires a dockboard or an edge-of-dock leveler.

Quick answers
  • Dock plate: Flat aluminum plate, no curbs. Published as not intended for fork trucks. 1,400 to 11,900 lb.
  • Dockboard: Forklift-rated bridge with welded safety curbs, in steel or aluminum. 5,000 to 25,000 lb.
  • How to tell them apart: Curbs. A dockboard has them. A dock plate does not.

The two words get used for the same thing on the dock. On a listing they are different products with different ratings. The curbs on a dockboard are there to keep a wheel from running off the side, which is the hazard that matters once a forklift is involved.

A note on this guide

This guide is written from published manufacturer data and my own experience quoting this equipment. It is general guidance and my opinion, not engineering advice. Confirm the rating for your exact model and application before you order.

Section Two

The difference in detail

Construction, capacity and what each is built to carry.

Short answer: A dockboard is thicker, curbed and rated for powered equipment. A dock plate is lighter, flat and rated for manual loads.

Dock plate vs. dockboard
DockboardDock plate
Forklift ratedYesNo, not intended for fork trucks
Run-off protectionWelded safety curbsNone
MaterialSteel (TS series) or aluminum (BTA series)Aluminum, 3/8 in. (E series) or 1/2 in. (EH series)
Listed capacity5,000 to 25,000 lb1,400 to 11,900 lb
Widths60, 72, 78, 84 in.30, 36, 48, 60, 72 in.
Lengths30 to 84 in.24 to 60 in.
HandlingLocking legs; steel boards add a lever liftBolt-on legs and side handles
Typical trafficForklifts, pallet trucksHand trucks, carts, foot traffic
Steel vs. aluminum dockboards
Steel (TS)Aluminum (BTA)
Capacity10,000 to 25,000 lb5,000 to 20,000 lb
Widths60, 72, 84 in.60, 72, 78, 84 in.
Lengths36 to 72 in.30 to 84 in.

Aluminum is lighter to position. Steel carries more. Both dockboard families have an 11 degree bend 9 in. from the beveled edge and legs 12 in. from the edge.

Section Three

Sizing capacity

The board carries the truck, not just the pallet.

Short answer: Capacity needed equals the forklift's service weight plus the heaviest load plus the operator. Buy above that total.

Read the service weight from the truck's data plate. A 3,000 lb pallet on a 9,000 lb truck is a 12,000 lb crossing load before the operator. That rules out every dock plate and the lighter aluminum dockboards.

For hand trucks and carts, use the loaded weight of the heaviest cart. Dock plate capacity depends heavily on size:

Published dock plate capacities
Size (width x length)E series, 3/8 in.EH series, 1/2 in.
48 x 24 in.5,200 lb8,200 lb
72 x 24 in.6,500 lb11,900 lb
30 x 24 in.3,000 lbSee listing
30 x 48 in.1,400 lbSee listing

Notice the last two rows. The same 30 in. wide plate drops from 3,000 lb to 1,400 lb when the length doubles. A longer plate spans more and holds less.

Section Four

Sizing length and width

Length is set by the height difference between the dock and the trailer bed.

Short answer: Measure the largest height difference you will see and match the length to it. A longer board bridges a bigger difference at a safe grade.

Steel dockboard length by height difference
Board lengthHeight difference
36 in.5 in.
48 in.7 in.
60 in.10 in.
72 in.12 in.

Measure the dock height, then the bed height of the highest and lowest trailers you load. Size to the largest difference in either direction.

Worked example

Your dock is 48 in. high. Trailer beds run from 44 in. to 55 in. The differences are 4 in. down and 7 in. up. The largest is 7 in., so a 48 in. long steel dockboard covers it. With a 9,000 lb truck and 3,000 lb loads you need more than 12,000 lb, and a board wide enough for the truck. The Vestil model number tells you all three: a TS-25-7248 is a steel board rated 25,000 lb, 72 in. wide and 48 in. long.

For width, the board has to be wider than the equipment crossing it and narrower than the trailer door opening.

Section Five

What OSHA requires

Dockboards have their own section in the walking-working surfaces rule.

Short answer: OSHA 29 CFR 1910.26 covers dockboards: capacity, run-off protection, securing the board, securing the vehicle and handholds.

  • 1910.26(a). The board must support the maximum intended load.
  • 1910.26(b). Boards first put into service on or after January 17, 2017 need run-off protection, unless there is no run-off hazard.
  • 1910.26(c). Portable boards must be anchored or otherwise secured so they cannot move.
  • 1910.26(d). Chocks or sand shoes to keep the transport vehicle from moving while the board is in use.
  • 1910.26(e). Handholds or an equivalent means for safe handling.

OSHA 1910.178 adds the truck side: brakes set and wheels chocked, and fixed jacks under an uncoupled semitrailer.

Section Six

Choosing by application and common mistakes

Find your row, then check the list.

Short answer: The mistake that hurts people is running a forklift over a dock plate.

Hand trucks, carts and foot traffic only
Aluminum dock plate. Check capacity at your length.
Pallet jacks, manual or powered
Dockboard.
Forklifts
Dockboard or edge-of-dock leveler. Size capacity to truck plus load plus operator.
Heaviest trucks and loads
Steel dockboard, 10,000 to 25,000 lb.
Board is moved by hand often
Aluminum dockboard, 5,000 to 20,000 lb.
Same trailer heights every day, constant use
Edge-of-dock leveler, listed from 6,000 to 30,000 lb. See our dock equipment guide.
  • Forklift on a dock plate. Dock plates are published as not intended for fork trucks.
  • Sizing capacity to the pallet. Add the truck's service weight.
  • Sizing length to the typical trailer. Size to the largest height difference, not the usual one.
  • Skipping the chocks. Secure the board and chock the trailer every time.
Section Seven

Frequently asked questions

The questions I hear most on quote calls.

What is the difference between a dock plate and a dockboard?

A dock plate is a flat aluminum plate without curbs for hand trucks, carts and foot traffic. A dockboard is a heavier, forklift-rated bridge with welded safety curbs, made in steel or aluminum.

Can I drive a forklift over a dock plate?

No. The Vestil aluminum dock plates are published as not intended for fork trucks. A forklift crossing requires a dockboard or an edge-of-dock leveler.

How much weight can a dockboard hold?

Vestil steel dockboards are listed from 10,000 to 25,000 lb and aluminum dockboards from 5,000 to 20,000 lb.

How do I figure the capacity I need?

Add the forklift's service weight from its data plate, the heaviest load and the operator. A 3,000 lb pallet on a 9,000 lb truck is a 12,000 lb crossing load.

How long should a dockboard be?

Match length to the largest height difference between the dock and the trailer bed. On steel dockboards, 36 in. covers 5 in., 48 in. covers 7 in., 60 in. covers 10 in. and 72 in. covers 12 in.

Does OSHA regulate dockboards?

Yes. OSHA 29 CFR 1910.26 covers capacity, run-off protection, securing the board, securing the vehicle and handholds.

About the author. Tom McGovern is the owner of CustomMHS, an industrial material handling distributor serving the US, Canada and Mexico. He has worked in material handling since 1981 and has quoted and specified the Vestil steel truck dockboards and Vestil aluminum economizer dock plates sold at CustomMHS. Questions about this guide: 866-333-0728.

Ready for a quote?

Send us these details and a material handling specialist will reply, typically within one business day.

  • Dimensions
    Size of the load and the space it goes in
  • Load
    Weight per item, shelf or level
  • Quantity
    How many units you need
  • Delivery ZIP code
    For freight pricing
  • Drawing
    A sketch, photo or spec sheet, if you have one
Get a Fast Quote Call 866-333-0728

Not sure which one your dock needs?

Tell us what crosses the gap, the heaviest load, and the highest and lowest trailer bed you see, and we will size it. Quote requests are answered within 24 hours by a real person.

866-333-0728

Browse Vestil steel truck dockboards at custommhs.com

Browse Vestil aluminum dock plates

Browse all dock equipment

Get a fast quote

No bots. No guesswork. Real experts.

Specification sources

CustomMHS dock equipment guide and Vestil listings · OSHA 29 CFR 1910.26 (dockboards) and 1910.178 (powered industrial trucks).

Published figures are current as of November 2026 and are subject to change by the manufacturer. This guide is written from published manufacturer data and my own experience quoting this equipment. It is general guidance and my opinion, not engineering advice. Confirm the rating for your exact model and application before you order.