Industrial Equipment Experts Since 1980 | Mon–Fri, 7 AM–6 PM ET
No bots. Real experts. 866-333-0728
Get a Fast Quote
Get a Fast Quote

CustomMHS Buyer's Guide

Hoppers & Tilt Trucks

A hopper carries two capacity ratings, and only one of them limits you. Which one depends on what you put in it. Get it backwards and you either overpay or hang an overloaded hopper on a forklift.

Covers: Jesco · MECO · Vestil · Akro-Mils · Bayhead Questions: 866-333-0728 Written and reviewed by: Tom McGovern · November 2026
Section One

Two ratings, and only one of them limits you

Every hopper is sold with a weight rating and a volume rating. Most buyers read one and ignore the other.

Quick answers
  • Multiply the hopper volume in cubic yards by what a cubic yard of your material weighs. If the answer is over the weight rating, you can never fill that hopper.
  • Flattened cardboard runs about 100 lb per cubic yard. Stone or gravel runs about 2,632 lb per cubic yard. The same 2 cubic yard hopper holds 200 lb of one and 5,264 lb of the other.
  • A hopper on a forklift is an attachment. OSHA 1910.178(a)(4) and (a)(5) cover approval and marking of attachments, and the truck capacity has to be checked at the real load center.
  • No forklift in the area, or loads a person can push and tip? A tilt truck or chip truck is usually the better tool.

A listing will say something like 2,000 lb and 2 cubic yards. Those are two separate limits. For any one material, you will only ever reach one of them.

Limit one

You run out of room

The hopper fills before it gets heavy. This is cardboard, packaging, plastic and most general waste. You are buying volume, and the weight rating is spare.

Limit two

You run out of capacity

The hopper reaches its weight rating while it still looks half empty. This is machining chips, castings, stone, sand and wet material. You are buying strength, and the volume figure is the one that misleads you.

Both mistakes cost money. A 6,000 lb hopper for cardboard is steel you will never load. A large hopper for foundry sand is a container that, filled, weighs far more than the hopper is rated for and more than the forklift was planned for. The second mistake is the dangerous one.

The one question that sorts this out

What does a cubic yard of your material weigh? If you do not know, section two shows how to find out with a 5 gallon pail and a scale.

Please read this part

This guide is educational and reflects the opinion and general experience of CustomMHS as an equipment distributor. It is not a compliance assessment or legal advice. Powered industrial truck operation, including operator training, is governed by OSHA 1910.178 in full. Capacities and sizes are the manufacturers' published figures and can change. Confirm the current data sheet for your exact model before you order.

Section Two

The density math

A few minutes of arithmetic decides the whole purchase.

Short answer: Full weight = cubic yards × pounds per cubic yard. Compare that to the weight rating before you choose a size.

Full hopper weight = volume in cubic yards × material weight in lb per cubic yard
Below the weight rating
You run out of room first. Buy for volume.
Above the weight rating
You run out of capacity first. Buy a stronger hopper, a smaller one, or mark a fill line.
Usable fill
Weight rating ÷ lb per cubic yard = the cubic yards you can load

What a cubic yard of common material weighs

These are published volume-to-weight conversion factors from the EPA and Los Angeles County Public Works. They were written for waste reporting, and they are close enough to size a hopper from.

Pounds per cubic yard, loose unless noted
Material lb per cubic yard Weight of a full 2 cubic yard hopper
Plastic containers, mixed, loose 22 to 40 44 to 80 lb
Aluminum cans, uncompacted 46 92 lb
Corrugated cardboard, flattened 100 to 106 200 to 212 lb
Wood, pallets and clean lumber 169 338 lb
Mixed municipal waste, uncompacted 250 to 300 500 to 600 lb
Mixed office paper, loose 323 646 lb
Glass bottles, loose 380 760 lb
Metal scrap 906 1,812 lb
Concrete, scrap, loose 1,855 3,710 lb
Soil, dry 2,025 4,050 lb
Soil, wet 2,106 4,212 lb
Stone or gravel 2,632 5,264 lb

Worked example: one hopper, two materials

Take the MECO medium duty SDHM200, listed at 2 cubic yards and 2,000 lb.

The same 2 cubic yard, 2,000 lb hopper
Material Math Result
Flattened cardboard at 100 lb per cubic yard 2 × 100 = 200 lb You use 10% of the weight rating. You will run out of room every time.
Stone or gravel at 2,632 lb per cubic yard 2 × 2,632 = 5,264 lb More than two and a half times the rating if filled.
Usable fill with gravel 2,000 ÷ 2,632 = 0.76 cubic yards You can only load it 38% full.

Nothing about a hopper stops someone from filling it to the brim, and nothing about the material announces its weight. The operator sees a container that is two thirds empty and keeps loading.

Worked example: weigh your own material with a 5 gallon pail

Machining turnings, wet scrap, castings, foundry sand and sludge vary widely and are often denser than a table suggests. A cubic yard is 27 cubic feet, which is about 202 gallons, so a 5 gallon pail is about 1/40 of a cubic yard.

  1. Weigh the empty pail.
  2. Fill it level with your material, the way it really goes into the hopper. If the material is wet or oily, weigh it wet or oily.
  3. Weigh it again and subtract the pail.
  4. Multiply the net weight by 40. That is your approximate lb per cubic yard.

Example: a level pail of steel turnings weighs 32 lb and the pail weighs 2 lb. 30 lb × 40 = about 1,200 lb per cubic yard. A 2,000 lb hopper can take about 1-2/3 cubic yards of that material, so a 2 cubic yard hopper would be over its rating when full and a 1-1/2 cubic yard hopper would not.

Section Three

Capacity, duty names and steel gauge

The duty name on a listing is a label. The capacity and the steel are the facts.

Short answer: Read the pound rating, the body gauge and the base thickness. Do not rely on words like medium, heavy or extra heavy, because each brand uses them differently.

Steel gauge runs backwards: a lower number is thicker steel. 7 gauge is thicker than 10 gauge, which is thicker than 12 gauge.

Duty names are not standardized between brands. On our listings, the Jesco heavy duty formed base hopper is a 2,000 lb hopper in sizes from 1/4 to 4 cubic yards, and the MECO medium duty hopper is also 2,000 lb, in eight sizes from 1/4 to 2-1/2 cubic yards. The Jesco super extra heavy duty hopper is 6,000 lb in 1 to 2-1/2 cubic yards. Compare the numbers, not the names.

Body and base steel as listed
Hopper Body Base
Jesco self-dumping hopper 10 gauge 8 gauge
MECO extra duty 7 gauge 7 gauge
MECO Series 90 extra duty 7 gauge 1/4 in
Jesco super duty 7 gauge 1/4 in
Jesco large volume 7 gauge 1/4 in to 3/8 in
Jesco low profile 12 gauge 8 gauge
Jesco low profile, plate base 12 gauge 1/4 in
MECO low profile 7 gauge 7 gauge

Read the base separately from the body

The body takes abrasion. The base takes the impact when castings, chips or scrap are dropped in from a height, and it carries the concentrated load when the hopper is full.

Some lines pair the same body gauge with a heavier base, such as a 12 gauge body on a 1/4 in base. If your material is dropped in and not placed, the heavier base is usually a better use of money than a heavier body.

Buy for the worst material, not the average

Choose the hopper for the heaviest, sharpest thing that will go in it. Hoppers get used for whatever is nearby, and a light hopper that sometimes receives castings will fail at the base first.

Section Four

How a self-dumping hopper dumps

The point of the design is that the operator never leaves the forklift seat.

Short answer: The body pivots on a base that stays on the forks. Release the latch, the load tips the body forward, and the empty body swings back and relatches.

The hopper body pivots on a frame that stays on the forks. A latch holds the body upright. The operator releases the latch from the seat, the body tips forward under the weight of its contents, and it relatches automatically when it is empty.

Two things follow from that:

  • It needs weight to dump. The contents drive the rotation, so a nearly empty hopper may not tip willingly.
  • The latch is the safety device. It is also a wear item. A latch that does not fully engage is a hopper that can dump when nobody planned it.

Dump angle

A standard hopper tips far enough to discharge most material. A 90 degree hopper, such as the Vestil 90 degree low profile hopper, rotates further. That matters for material that clings: wet scrap, sticky waste and fine chips that pack. If operators are shaking or prodding a hopper to empty it, dump angle is the fix.

Open end hoppers

An open end hopper has an unobstructed end for loading long or awkward material and for raking material out.

Where you dump matters as much as how

Discharge is a moment of concentrated, shifting weight. Square the truck to the dumpster, keep everyone clear of the arc, and dump at the lowest practical height.

Section Five

Low profile hoppers

Where the standard hopper shape is the problem.

Short answer: A low profile hopper lowers the loading edge. Buy one when people lift scrap over a high rim or the hopper has to fit under a machine or conveyor.

A low profile hopper has a reduced overall height, so the loading edge sits lower. This is an ergonomics purchase. If people lift scrap over a chest-high rim all day, a low profile hopper takes that lift away. It also fits under machinery and conveyor discharge points where a standard hopper will not.

We list low profile hoppers from Jesco, MECO and Vestil. The same rules apply as for any hopper: run the density math, then read the capacity, body gauge and base thickness on the listing.

Section Six

The forklift side of the purchase

A hopper is a forklift attachment. That changes the math on the truck, not just the hopper.

Short answer: Add the empty hopper weight to the load, then check the total against the truck's capacity at the hopper's real load center, not the 24 in figure on the data plate.

Forklift capacity is stated at a load center, commonly 24 in from the face of the forks. A hopper puts its weight further forward than a pallet does, because the body extends past the fork pockets and the contents fill toward the front. As the load center moves out, the truck's capacity goes down.

Empty hopper weight + contents weight = total load, at the hopper's actual load center
Check it against
The truck's capacity at that load center, from the truck manufacturer or dealer

A hopper full of gravel can be over its own rating and over the truck's reduced capacity while it looks like an ordinary lift.

Fork pockets and the safety chain

Confirm that the fork pocket size and spacing match your forks. Confirm there is a chain or other retainer that secures the hopper base to the truck. Dumping throws the body forward, and the retainer is what keeps the base on the forks while that happens.

Use the safety chain every time

It is the most commonly skipped step with a self-dumping hopper, and it matters most during the dump. A hopper that slides forward while tipping goes somewhere nobody planned.

Section Seven

What OSHA requires

Two rules about attachments that many buyers have never read, one about tilting, and one about parking.

Short answer: Get the truck manufacturer's written approval for the attachment, have the truck marked for it, do not travel with the load raised and tilted, and lower the hopper before you leave the truck.

Attachments need written approval

Under 29 CFR 1910.178(a)(4), the customer or user may not make modifications or additions that affect capacity and safe operation without the truck manufacturer's prior written approval, and the capacity, operation and maintenance plates, tags or decals must be changed to match.

The truck must be marked for the attachment

1910.178(a)(5) covers trucks with front-end attachments other than factory installed ones. The user must ask that the truck be marked to identify the attachment and to show the approximate weight of the truck and attachment combination at maximum elevation with the load laterally centered. In plain terms: if you hang a hopper on a forklift, the truck's markings should reflect it.

Attachments and an empty truck

1910.178(o)(4) says a truck equipped with an attachment is operated as a partially loaded truck when it is not handling a load. An empty hopper is still weight out front.

Tilting a raised load

1910.178(o)(6) prohibits tilting forward with the load engaging means elevated except to pick up a load, and says an elevated load is not tilted forward except when it is in a deposit position over a rack or stack. Position the hopper over the dumpster first, then dump. Do not travel with it raised and tilted.

Leaving the truck

1910.178(m)(5)(i) requires that when a truck is left unattended, the load engaging means are fully lowered, the controls neutralized, the power shut off and the brakes set. A hopper parked in the air on an unattended truck is a violation and an obvious hazard.

This is a summary, not a compliance program

Powered industrial trucks are governed by 1910.178 in full, including operator training and evaluation. Use this section to specify and use hoppers sensibly, and confirm your program against the standard and your own safety staff.

Section Eight

Tilt trucks and chip trucks

The no-forklift half of this category, and often the better answer.

Short answer: A tilt truck is pushed and tipped by a person. Choose polyethylene for general and wet waste, steel for hot, sharp or oily material, and a self-dumping hopper once the load is beyond what a person should push.

Tilt trucks

A tilt truck is a wheeled container balanced so one person can roll it and tip it. The tilt turns emptying from a lift into a controlled pour.

Bayhead tilt trucks have seamless polyethylene bodies and are listed in capacities from 1/3 to 3 cubic yards. Polyethylene does not rust or dent, which suits general waste and wet areas. We also list Akro-Mils heavy duty tilt trucks.

Chip trucks

Chips and turnings from machining are abrasive, sharp, usually carry cutting oil, and are heavier than they look. The Jesco tilt chip and waste truck is listed with a 14 gauge steel body and a leakproof design, in a compact footprint for aisles and work cells. We also list the Vestil chip truck.

Hopper or tilt truck
Choose a self-dumping hopper when Choose a tilt truck when
The load is heavy, 2,000 lb and up The load is within what a person can push and tip
A forklift already works in the area There is no forklift, or you are cutting forklift traffic
You dump into a tall dumpster or compactor You dump at or near floor level
The trip is long or crosses the plant The trip is short and stays in one area
The material is dense or abrasive The material is light or general waste

Many plants run both: tilt trucks collect at the machine, and a hopper makes the trip to the dumpster.

Section Nine

Lids, casters and drains

Small items. Two of them change what the hopper can do.

Short answer: Add a lid for light material or outdoor storage, casters to fill at the source, and a way to drain liquid before you move a hopper that holds coolant or rainwater.

Lids

Hopper lids keep light material from blowing out, keep rain out, and keep a parked hopper from becoming everyone's trash can.

Casters

Casters let a hopper be rolled to where the scrap is made, filled there, and picked up only when it is time to dump. See Jesco hopper casters and MECO hopper caster sets. Casters have their own capacity, so check the caster rating against the loaded weight. Our carts and casters guide covers caster selection.

Drains

Coolant, cutting oil and rainwater collect in the bottom of a hopper. Water weighs about 8.34 lb per gallon, so 50 gallons of rainwater is more than 400 lb that nobody counted. If your material is wet or the hopper lives outdoors, ask about a drain option on the model you are quoting, and drain before moving.

Section Ten

Choosing by application

Find the row that matches your situation.

Short answer: Light waste: buy volume. Dense material: buy capacity and a small volume. No forklift: buy a tilt truck.

Cardboard, packaging and light waste
You will run out of room long before you reach the weight rating. Buy the largest volume you can handle at 2,000 lb, and add a lid.
Machining chips and turnings
A chip truck at the machine, or a hopper with a heavier base. Weigh a pail of chips first. They are denser than they look.
Castings, forgings and dense metal scrap
A 7 gauge body with a 1/4 in or thicker base, because the material is dropped in. Run the density math before choosing volume.
Stone, sand, soil or concrete
At 1,855 to 2,632 lb per cubic yard, a 2 cubic yard hopper passes a 2,000 lb rating when it is well under half full. Buy small volume and high capacity, and mark a fill line.
People lift scrap over a high rim
A low profile hopper. It also fits under machines and conveyor discharge points.
Material clings or will not empty cleanly
A 90 degree dump hopper.
Fill at the source, move it later
A hopper on casters. Check the caster rating against the loaded weight.
No forklift, or less forklift traffic
A tilt truck. Polyethylene for general waste and wet areas, steel for hot, sharp or oily material.
Dumping into a tall dumpster or compactor
A self-dumping hopper on a forklift. Confirm the truck's capacity at the hopper's real load center.
The hopper lives outdoors
A lid, and a way to drain it. Rainwater adds weight nobody accounts for.
A mixed waste stream you cannot pin down
Specify for the heaviest thing that will realistically go in.
Section Eleven

Common mistakes, and what to inspect

The first four are safety issues. The rest are money.

Short answer: The costly mistakes are sizing by volume for dense material, ignoring the forklift load center, skipping the safety chain, and never testing the latch.

Sizing by volume when the material is dense

A 2 cubic yard hopper of gravel is over 5,000 lb against a 2,000 lb rating.

Ignoring the load center

Check the truck's capacity at the hopper's actual load center, with the empty hopper weight included.

Not using the safety chain

The retainer is what keeps the base on the forks during the dump.

Missing the OSHA attachment rules

1910.178(a)(4) and (a)(5): written approval, and the truck marked for the attachment.

Buying on the duty name

One brand's heavy duty is another brand's medium duty. Compare pounds, gauge and base.

Overbuying for light waste

Cardboard at 100 lb per cubic yard uses 10% of a 2,000 lb rating in a 2 cubic yard hopper.

Exceeding the caster rating

A hopper inside its own rating can still be over what its casters will carry.

Inspection checklist

  • Latch: test that it fully engages. Take the hopper out of service if it does not. There is no safe workaround for a failed latch.
  • Pivots: look for wear, stretched holes and dry pins.
  • Release cable or lever: check for fraying, kinks and free movement.
  • Base: look for cracks, deformation and wear-through, especially if material is dropped in.
  • Fork pockets and chain: check for spreading, and confirm the safety chain is present and undamaged.
  • Welds: check the pivot mounts and the base, which are the highest-stress joints.
  • Casters: check for flat spots and stiff swivels.
  • Truck markings: confirm the forklift is still marked for the attachment.

Follow the inspection interval in the manufacturer's manual for your hopper. The list above is a general guide.

Section Twelve

Frequently asked questions

What comes up most often on quote calls.

How do I choose between the weight rating and the volume rating?

Multiply the hopper volume in cubic yards by what a cubic yard of your material weighs. If the result is below the weight rating, volume is your limit and you should buy for volume. If it is above, weight is your limit and you need a stronger or smaller hopper.

What does a cubic yard of my material weigh?

Published conversion factors put flattened cardboard at about 100 to 106 lb per cubic yard, mixed uncompacted waste at 250 to 300 lb, metal scrap at about 906 lb and stone or gravel at about 2,632 lb. For chips, castings, sand or anything wet, weigh a level 5 gallon pail of it, subtract the pail, and multiply by 40.

What do the gauge numbers mean?

Steel gauge runs backwards, so a lower number is thicker. 7 gauge is thicker than 10 gauge, and 10 gauge is thicker than 12 gauge. Read the base thickness separately from the body, because the base takes the impact.

How does a self-dumping hopper work?

The body pivots on a base that stays on the forks, and a latch holds it upright. The operator releases the latch from the forklift seat, the weight of the contents tips the body forward, and the empty body swings back and relatches.

Why will my hopper not empty completely?

Material that is wet, sticky or packed clings to the body at a standard dump angle. A 90 degree dump hopper rotates further and clears it. A nearly empty hopper may also not tip, because the contents drive the rotation.

Does a hopper change my forklift capacity?

Yes. A hopper is an attachment with its own weight, and it carries the load further forward than a pallet. Add the empty hopper weight to the contents and check the total against the truck's capacity at the hopper's actual load center.

What does OSHA require when I put a hopper on a forklift?

OSHA 1910.178(a)(4) requires the truck manufacturer's prior written approval for additions that affect capacity and safe operation, with the plates changed to match. 1910.178(a)(5) requires the user to ask that the truck be marked to identify the attachment and the combined weight.

Can I tilt forward with the hopper raised?

OSHA 1910.178(o)(6) prohibits tilting forward with the load engaging means elevated except to pick up a load or when the load is in a deposit position. Position the hopper over the dumpster, then dump. Do not travel with it raised and tilted.

Hopper or tilt truck?

Use a self-dumping hopper when loads are heavy, a forklift is already in the area, or you dump into a tall dumpster. Use a tilt truck when a person can push and tip the load, the trip is short, and you dump near floor level.

Steel or polyethylene tilt truck?

Polyethylene does not rust or dent and suits general waste and wet areas. Steel suits hot, sharp or oily material such as machining chips.

Do I need a lid?

Add a lid when the material is light enough to blow out, when the hopper sits outdoors, or when a parked hopper tends to collect trash it was not meant for.

Section Thirteen

Quick-reference tables

Published figures and citations used in this guide.

OSHA requirements
Topic What it says Source
Attachment approval No additions that affect capacity and safe operation without the manufacturer's prior written approval. Plates changed to match. 1910.178(a)(4)
Attachment marking Truck marked to identify the attachment and show the approximate combined weight at maximum elevation, load laterally centered. 1910.178(a)(5)
Empty attachment A truck with an attachment is operated as partially loaded when not handling a load. 1910.178(o)(4)
Tilting raised loads No forward tilt with the load raised except to pick up a load or in a deposit position. 1910.178(o)(6)
Unattended trucks Load lowered, controls neutral, power off, brakes set. 1910.178(m)(5)(i)
Product families we list
Family Listings Published on the listing
2,000 lb hoppers MECO medium duty, MECO Series 90, Jesco heavy duty, Vestil MECO: eight sizes, 1/4 to 2-1/2 cubic yards. Jesco: 1/4 to 4 cubic yards
Heavier hoppers MECO heavy duty, MECO Series 90 heavy duty, Jesco 10 gauge, MECO extra duty, MECO Series 90 extra duty See listing for capacity by model
6,000 lb and large volume Jesco super extra heavy duty, Jesco large volume Super: 6,000 lb, 1 to 2-1/2 cubic yards, 7 gauge body, 1/4 in base
Low profile Jesco, Jesco plate base, MECO, Vestil 90 degree See listing
Open end Vestil open end hopper See listing
Chip trucks Jesco, Vestil Jesco: 14 gauge steel, leakproof
Tilt trucks Bayhead, Akro-Mils Bayhead: polyethylene, 1/3 to 3 cubic yards
Accessories Lids, Jesco casters, MECO casters See listing
Before you order

The density figures are published conversion factors written for waste reporting. They are not a substitute for weighing your own material, especially anything wet, oily or metallic. Tell us the material, a cubic yard weight if you have one, and how you dump, and we will size it with you.

About the author. Tom McGovern has worked in the industrial material handling industry since 1981, bringing over 45 years of hands-on experience helping businesses select the right equipment for their applications. His expertise includes specifying and quoting Jesco, MECO and Vestil self-dumping hoppers, chip trucks and tilt trucks.

Questions about this guide? Call 866-333-0728 to speak with an experienced material handling specialist.

Ready for a quote?

Send us these details and a material handling specialist will reply, typically within one business day.

  • Dimensions
    Size of the load and the space it goes in
  • Load
    Weight per item, shelf or level
  • Quantity
    How many units you need
  • Delivery ZIP code
    For freight pricing
  • Drawing
    A sketch, photo or spec sheet, if you have one
Get a Fast Quote Call 866-333-0728

Tell us what a cubic yard of it weighs

That one number decides whether you are buying volume or strength, and it is the question most quotes skip. Quotes are reviewed by material handling specialists, typically within one business day.

866-333-0728

Browse hoppers & tilt trucks at custommhs.com

No bots. No guesswork. Real experts.

Sources

OSHA 29 CFR 1910.178 · EPA Volume-to-Weight Conversion Factors, April 2016 · Los Angeles County Public Works volume to weight conversion table · Jesco, MECO, Vestil, Akro-Mils and Bayhead figures as published on CustomMHS product listings.

Disclaimer. This guide is educational content and reflects the opinion and general experience of CustomMHS. It is not a compliance assessment or legal advice. Powered industrial truck operation, including operator training, is governed by OSHA 1910.178 in full. Confirm equipment ratings, forklift capacity at your actual load center and attachment markings against the manufacturer's data and your own safety program. Reviewed November 2026.