Industrial Equipment Experts Since 1980 | Mon–Fri, 7 AM–6 PM ET
No bots. Real experts. 866-333-0728
Get a Fast Quote
Get a Fast Quote

CustomMHS Buyer's Guide

Carts, Trucks & Dollies

The cart is the easy part. The casters decide whether it rolls for ten years or fights your people every shift. Here is how to specify both, plus the load rule most buyers get wrong.

Covers: Little Giant · Metro · Jamco · Rousseau · Strong Hold · MECO · Akro-Mils · Bayhead Questions: 866-333-0728 Written and reviewed by: Tom McGovern · November 2026
Section One

The part nobody specifies

Buyers pick the cart by deck size and capacity, then accept whatever casters come standard. That is backwards.

Quick answers
  • Size casters by dividing the total loaded weight by three, not four, then add a safety margin. A 3,000 lb loaded cart needs casters rated at least 1,200 lb each.
  • Choose the wheel material for the floor first, then temperature, then chemicals, then load.
  • Bigger wheels are the cheapest way to make a cart easier to push. Use 4 to 5 in for general work and 6 in or more for rough floors.
  • Starting a cart should not take more than about 50 lb of push force. If it does, look at the wheels, the bearings and the load.

A cart is a steel frame with a deck on it. There is not much to get wrong, and the frame is rarely why a cart disappoints.

What disappoints is the rolling: a cart that will not track straight, that stops dead at a floor joint, that takes two people to start, or that marks a finished floor. Each of those is a caster problem. Casters are also the cheapest thing to get right at purchase and the most expensive to fix afterward.

So this guide covers casters first and the cart second. If you already know your casters, jump to cart types.

Please read this part

This guide is educational and reflects the opinion and general experience of CustomMHS as an equipment distributor. Caster sizing practice and push force figures are guidance, not regulation. Confirm against the caster and cart manufacturer's ratings, and where you have an ergonomics concern, get a qualified assessment.

Section Two

Casters: the three-caster rule

The most common specification error in this category, and it is a division problem.

Short answer: On a real floor only three of four casters carry the load at any moment. Divide the total loaded weight by three, then add a safety margin of at least 20 percent.

You have a 3,000 lb cart with four casters, so each caster carries 750 lb. That reasoning is common and wrong.

Concrete is not flat, frames flex, and loads sit unevenly. At any moment three casters carry the weight and the fourth floats. Which one floats changes as the cart moves. So you divide by three, then add a margin for the shock of crossing floor joints and dock plates.

Rating per caster = (total loaded weight ÷ 3) × 1.2
÷ 3
Three casters carry the load, not four
× 1.2
A 20 percent safety margin as a starting point. Use more for harder duty
Total weight
The payload plus the weight of the cart itself
Worked examples
  • 3,000 lb loaded cart: 3,000 ÷ 3 = 1,000 lb. 1,000 × 1.2 = 1,200 lb per caster. Dividing by four gives 750 lb, which is 450 lb short.
  • 1,200 lb payload on a 200 lb cart: 1,400 ÷ 3 = 467 lb. 467 × 1.2 = 560 lb per caster.
  • Harder duty: the same 3,000 lb cart with a 50 percent margin needs 1,000 × 1.5 = 1,500 lb per caster.

A six-wheel cart spreads the load across more casters and turns more tightly. If a four-wheel cart is near the top of its caster rating, a six-wheel version of the same deck is often the simpler fix.

Section Three

Wheel material

This is a floor decision as much as a load decision.

Short answer: Use non-marking polyurethane or rubber on finished floors, ask for high-temperature wheels around ovens, and save cast iron and steel for the heaviest work.

Wheel material comparison
Material Floor protection Rolling Noise In our experience it suits
Polyurethane Very good, with non-marking options Smooth and easy Quiet Sealed and epoxy floors and smooth concrete. The usual choice for indoor work.
Rubber Very good Good grip, absorbs shock Quiet Tile and sealed floors, where protecting the floor matters more than capacity.
Phenolic Poor. Hard, and can mark Easy under heavy loads Louder Heavy loads. High-temperature versions are made for ovens and bakeries.
Nylon and plastics Fair Varies Can chatter on rough floors Budget work and some chemical resistance needs.
Cast iron and steel None. Will scar most floors Easy under very heavy loads Very loud Foundries and heavy industrial work.

How to choose

  1. Is the floor finished? Epoxy, sealed concrete or tile means non-marking polyurethane or rubber.
  2. Is there heat? Tell us the actual temperature. Standard wheels are for room-temperature work, and wheel materials vary widely in what they tolerate.
  3. Is there oil, chemicals or washdown? That narrows the wheel material and points to sealed bearings.
  4. How heavy, really? Only now does capacity narrow the choice.
The trade you are making

Soft wheels protect floors and roll quietly, but they squash under load, which makes the cart harder to push, and they can flat-spot if a loaded cart sits for weeks. Hard wheels roll easily under heavy loads and pass every bump into the load and the operator's hands. Pick the drawback you can live with.

Section Four

Diameter, bearings and layout

Three more caster choices that decide how the cart feels in a person's hands.

Short answer: Buy the largest wheel the deck height allows, upgrade the bearings on carts that move all day, and use two rigid casters or a six-wheel layout for long straight runs.

Wheel diameter
Diameter Use it for
2 to 3 in Smooth floors and tight spaces only. Takes more force and stops at thresholds and floor joints.
4 to 5 in The all-round choice for carts and benches.
6 in and up Rough floors, thresholds, dock plates and longer runs.

A larger wheel meets an obstacle at a shallower angle, so it rolls over what a small wheel stops at. The cost is deck height: a 6 in caster raises the load surface.

Bearings
Bearing Rolling effort Use it for
Plain bearing Highest Equipment that is moved only now and then.
Roller bearing Moderate The common industrial choice for frequent movement.
Sealed precision ball bearing Lowest Constant movement, debris and washdown.

Swivel and rigid layout

  • Four swivel. Moves in any direction, including sideways. Good in tight areas, poor over distance because it wanders.
  • Two swivel, two rigid. Tracks straight and steers from one end. The standard for longer runs.
  • Six wheel, four swivel plus two rigid. The center wheels let the cart pivot nearly in place while still tracking straight.

Brakes

Specify brakes wherever a cart is loaded by hand, parked on a slope or used as a work surface. A wheel brake stops the wheel turning. A total-lock brake stops the wheel and the swivel, which is what you want on a cart that must not creep. Ask for total lock by name.

Section Five

Push force and ergonomics

The reason to buy a cart is to save people's backs. Check that it does.

Short answer: If starting a loaded cart takes more than about 50 lb of force, fix the wheels and bearings or reduce the load before you buy another cart.

Two forces matter. The starting force, to get the cart moving, is always the larger. The rolling force keeps it going.

Published ergonomics guidance puts a practical ceiling of about 50 lb on the force to start a cart. If your people lean into a cart with a shoulder to get it going, it is overloaded, under-wheeled or worn out. For a formal assessment, the Liberty Mutual tables, often called the Snook tables, give acceptable push and pull forces by distance and frequency.

The cheap fixes, in order
  1. Larger diameter wheels.
  2. Better bearings.
  3. Less load, or two trips.
  4. Fix the floor at the exact spot people complain about.
  5. A handle at the right height.

Rolling effort is not constant. Frames bend, wheels get cut or go out of round, and bearings wear. A cart that was easy when new can become a two-person job without anyone deciding anything.

Section Six

Cart types by job

With the casters settled, the cart is mostly a question of what the load looks like.

Short answer: Shelf carts for picking, deep shelf and stock trucks for volume, platform trucks for bulky loads, box and bulk trucks for loose material, and drawer carts for tools.

Picking and service

Utility and service carts

Two or three open shelves for order picking and parts runs. See service and order picking carts, wire utility carts and plastic utility carts.

Volume transport

Shelf and stock trucks

Deeper and heavier. Little Giant deep shelf trucks come with 3 in to 12 in deep shelves and solid sides, or 12 in deep shelves with mesh sides. See also stock trucks and Metro wire stock carts.

Bulk and awkward

Platform and stake trucks

A flat deck for crates, machines and oversized loads. See platform and stake trucks and transport carts.

Loose material

Box and bulk trucks

Sides contain loose or bulky material. See Little Giant box trucks, 2 and 3 sided bulk trucks and Bayhead poly bulk trucks.

Heavy items, low lift

Low profile carts

A low deck means less lifting on every load and a lower center of gravity. See Jamco and Strong Hold low profile carts.

Clean areas

Stainless and polymer carts

For washdown, food, pharmaceutical and lab work. See stainless steel carts and MetroMax polymer stock carts.

Security

Controlled access carts

Lockable enclosures for valuable inventory in transit. See controlled access security carts.

Short moves

Dollies and hand trucks

The lowest-cost mobility there is. See steel and plastic dollies and hand, drum and cylinder trucks.

Open shelves or enclosed?

Open wire shelves are lighter, easier to clean and let you see the load. Solid shelves with a lip keep small parts from sliding off. Mesh sides give containment with visibility. Ask what happens if the cart goes round a corner fast.

Section Seven

Building a cart from components

A wire utility cart is a shelving unit with casters under it, and the parts are sold separately.

Short answer: You can build a wire cart from shelves, posts and casters, but the cart's rating becomes the caster rating, and mobile posts are different parts from stationary posts.

The same shelves, posts, dividers and casters that make a stationary wire unit can make a cart. That lets you build the exact cart you want, convert a unit you own, or add a shelf later. See wire shelves, posts, dividers and casters and the polymer versions.

The casters set the capacity

Put a shelving unit on casters and its stationary rating no longer applies. The mobile rating is whatever the caster set carries, and it is usually far lower. Ask for the rating of the unit on the casters you are choosing, in writing.

Stationary posts and mobile posts are different parts

Stationary posts have leveling feet. Mobile posts are made to take a caster stem. Order mobile posts, or order the conversion as a set, and check that the caster stem matches.

Where the load is heavy or awkward instead of numerous, a shelf cart is the wrong shape and a low profile cart is the right one. Finish choices for wire parts are covered in our industrial shelving guide.

Section Eight

Tool storage that moves

The same drawers, bins and panels you would fix in place, put on wheels.

Short answer: If the work always happens in one place, buy a stationary cabinet. If the tools must go to the machine, buy a cart, and ask for the cart capacity and the drawer capacity separately.

The work always happens in the same place
A stationary cabinet or a bench with drawers. See our cabinets guide and workbenches guide.
The work happens at the machine
A cart, so the tools travel to the job.
Tools are shared across people or shifts
A lockable cart, so accountability travels with the tools.
It moves twice a year
Buy stationary and use a pallet jack for the two moves.

Modular drawer tool carts carry up to 400 lb per drawer. A drawer rated 400 lb is still 400 lb on wheels. What changes is the total the cart can carry, which depends on the frame and the casters. Ask for both numbers.

Drawers, panels or bins
Format Best where See
Drawers Tools are valuable or the cart travels through areas you do not control. Modular drawer tool carts
Pegboard and A-frame A fixed tool set must be complete at the end of a job. A missing tool shows at a glance. A-frame tool carts
Bins The cart carries small parts and hardware. Little Giant bin carts
CNC tooling Toolholders go to the machine. Rousseau CNC tool carts, 41 in and 59 in high
Two-sided carts need room on both sides

Double-sided carts are excellent in an open bay and a problem in an aisle. Check the working clearance, not just the footprint.

Section Nine

Reading a deck and frame spec

Fewer traps here than in casters, but a few specs repay attention.

Short answer: A cart's capacity is the total for the whole cart, evenly spread. Load heavy items on the bottom shelf.

Capacity, and how it is spread

A published capacity is a total across the cart, evenly distributed. A cart rated at 3,600 lb across three shelves is not rated for 3,600 lb on the top shelf. Load heavy on the bottom shelf.

Gauge and construction

Lower gauge numbers mean thicker steel. All-welded construction stays tight where bolted assemblies can loosen.

Shelf edges: flush or lipped

Flush edges let you slide large items on and off. A lip keeps small parts from sliding off. Many cart families offer both.

Working height

A top shelf around 36 in (3 ft) is a comfortable standing work height. A lower deck means less lifting for heavy items.

Handles

A handle at the wrong height wastes force. On a cart pushed often and far, ask about handle height.

Section Ten

Specialty carts

Where a general-purpose cart is the wrong tool.

Short answer: Long, flat, round and pressurized loads each have a purpose-built cart that makes the move a one-person job.

Specialty carts we list
Cart What it does
Sheet and panel trucks Carry large flat material upright so it does not bend or get damaged.
Bar and pipe handling Cradles for long stock that would overhang a flat deck.
Wire reel carts and caddies Hold spools so wire, cable or hose pays out under control.
MECO and Little Giant cylinder trucks Move compressed gas cylinders with restraints. A safety item, not a convenience.
Drum trucks Tilt and move a full drum.
Akro-Mils and Bayhead tilt trucks Turn emptying waste, scrap and chips from a lift into a controlled pour.
Instrument carts Shelving for sensitive equipment. Soft, larger wheels reduce the shock to what rides on top.
Pallet stands Raise a pallet to working height so people are not bending to the floor all day.
Section Eleven

When manual stops making sense

There is a point where another manual cart is the wrong answer.

Short answer: If a load needs two people to start even with the right wheels, or the route has ramps, price a powered option before you buy more carts.

  • Loads often need two people to start moving.
  • Push force is too high even with correct wheels and good bearings.
  • The same long run happens many times a shift.
  • There are ramps or slopes on the route.
  • You have injury claims tied to moving material.

Those are the signs you have reached the limit of what a person should push. A powered unit moves the load while the operator steers. Before going powered, check the route. One bad floor joint, a threshold or a tight turn can cause most of the effort. Fixing four feet of concrete costs less than a powered fleet.

Section Twelve

Choosing by application

Find the row that matches your situation.

Short answer: Tell us the load, the floor, the distance and the temperature. Those four things specify the casters, and the casters are most of the decision.

Order picking in a stockroom
A two or three shelf utility cart on 4 to 5 in non-marking polyurethane wheels, four swivel. Add a shelf lip for small parts.
Long runs across a big facility
Two swivel and two rigid, or six wheels. 6 in wheels and sealed bearings.
Epoxy or sealed floor you care about
Non-marking polyurethane or rubber. Tell us the floor finish when you ask for a quote.
Hot parts, ovens, bakery
High-temperature wheels. Tell us the actual temperature.
Washdown, food, pharmaceutical or lab
A stainless or polymer cart with sealed bearings.
Rough floors, dock plates, expansion joints
The largest wheel the deck height allows, 6 in or more.
Heavy loads over 2,000 lb
Run the three-caster math with the cart's own weight and a larger safety margin. Consider six wheels.
Tools that must stay organized and secure
A modular drawer tool cart.
Sheet, panel, bar or pipe
Sheet and panel trucks or cradle carts.
Waste, scrap or machining chips
A tilt truck.
Compressed gas cylinders
A cylinder truck with restraints.
Cart doubles as a work surface
A top deck around 36 in, flush edges and total-lock brakes.
Section Thirteen

Maintenance, and why it matters more here

A worn cart keeps working. It just hands the extra effort to a person's shoulders.

Short answer: Inspect wheels and swivels on a schedule, replace casters in sets, and treat "this cart is hard to push" as a repair order.

  • Inspect wheels for flat spots, cuts and out-of-round.
  • Check the swivels. A stiff swivel makes the cart fight every turn.
  • Listen. A noisy caster has a bearing problem.
  • Check that the frame tracks true. Push an empty cart and see if it pulls to one side.
  • Clear debris from swivels and axles. Strapping and shrink wrap wind around axles.
  • Retighten caster mounting bolts.
  • Replace casters in sets.
  • Keep the bolt pattern on file. Record the plate size and hole spacing when you buy.
  • Act on complaints. It is the cheapest ergonomics check you will get.
Section Fourteen

Common and costly mistakes

Nearly all of these are caster mistakes.

Short answer: The big three are dividing the load by four, accepting the standard casters, and choosing wheels that are too small.

Dividing the load by four

Three casters carry the load on a real floor. Divide by three, then add a margin.

Forgetting the cart's own weight

Total loaded weight includes the cart.

Accepting whatever casters come standard

Standard casters are chosen to hit a price, not to suit your floor, load or distance.

Putting hard wheels on a finished floor

Phenolic and cast iron can mark epoxy and sealed concrete.

Choosing wheels too small

Small wheels are why a cart stops dead at a floor joint.

Asking for wheel brakes when you meant total lock

A wheel brake still lets the caster swivel.

Four swivel casters for long straight runs

The cart wanders and the operator fights it.

Loading heavy on the top shelf

Heavy goes low.

Buying more carts to solve a push problem

Another cart of the same kind will be just as hard to move.

Section Fifteen

Frequently asked questions

What comes up most often on quote calls.

How do I work out what caster capacity I need?

Divide the total loaded weight, including the cart, by three, then add a safety margin of at least 20 percent. A 3,000 lb loaded cart needs casters rated at least 1,200 lb each, not 750 lb.

Why divide by three when there are four casters?

Because concrete is never perfectly flat and frames flex. At any moment three casters carry the weight and the fourth floats. Sizing for a four-way split means every caster spends much of its life overloaded.

Which wheel material should I choose?

Start with the floor. Sealed, epoxy or finished floors need non-marking polyurethane or rubber. Then tell us the temperature, since standard wheels are for room-temperature work. Then consider chemicals and washdown. Capacity narrows the choice last.

Does wheel size really make that much difference?

Yes. A larger wheel rolls over thresholds and floor joints that stop a small one. 2 to 3 in suits smooth floors and tight spaces, 4 to 5 in is the all-round choice, and 6 in and up is for rough floors and longer runs. The cost is deck height.

How much force should it take to push a cart?

Published ergonomics guidance puts the practical ceiling for starting a cart at about 50 lb of force. For a formal assessment, use the Liberty Mutual tables, also called the Snook tables.

What is a six-wheel cart for?

Two extra wheels in the center let the cart pivot nearly in place while still tracking straight over longer pushes. They also spread the load across more casters.

Should I use swivel or rigid casters?

Four swivel moves in any direction and is best in tight areas, but it wanders over distance. Two swivel with two rigid tracks straight. Six wheels gives you both.

Is the published cart capacity per shelf or total?

Total, evenly spread, unless the listing says otherwise. Load heavy items on the bottom shelf.

Flush shelf edges or a lip?

Flush edges let you slide large items on and off. A lip keeps small parts from sliding off. Pick by whether your load is one big item or many small ones.

Do I need brakes?

Yes, wherever the cart is loaded by hand, parked on a slope or used as a work surface. Ask for total-lock brakes, which stop the wheel and the swivel.

Can I put casters on a wire shelving unit I already own?

Often, but the mobile rating is the caster set's rating, not the stationary rating, and mobile posts are different parts from stationary posts. Ask us to confirm the parts and the rating.

How often should carts be inspected?

On a schedule, not when people complain. Check for flat spots, stiff swivels, noise, debris on the axles and loose mounting bolts, and replace casters in sets.

Section Sixteen

Quick-reference tables

Guidance and product families referenced in this guide.

Caster selection reference
Item Figure Note
Capacity per caster (Total loaded weight ÷ 3) × 1.2 Three casters carry the load. 20 percent is a starting margin.
Worked example 3,000 lb loaded cart: 1,200 lb per caster Not 750 lb
Wheel diameter, tight spaces 2 to 3 in Smooth floors only
Wheel diameter, general use 4 to 5 in Carts and benches
Wheel diameter, rough floors 6 in and up Thresholds, dock plates, long runs
Force to start a cart About 50 lb Published ergonomics guidance
Before you order

Caster guidance here is industry practice, not a regulation, and the right safety margin depends on your floors, speeds and duty. Tell us the load, the floor finish, the distance and the temperature and we will specify the casters with the cart.

About the author. Tom McGovern has worked in the industrial material handling industry since 1981, bringing over 45 years of hands-on experience helping businesses select the right equipment for their applications. His expertise includes specifying and quoting service carts, shelf trucks, platform trucks and tool carts.

Questions about this guide? Call 866-333-0728 to speak with an experienced material handling specialist.

Ready for a quote?

Send us these details and a material handling specialist will reply, typically within one business day.

  • Dimensions
    Size of the load and the space it goes in
  • Load
    Weight per item, shelf or level
  • Quantity
    How many units you need
  • Delivery ZIP code
    For freight pricing
  • Drawing
    A sketch, photo or spec sheet, if you have one
Get a Fast Quote Call 866-333-0728

Tell us the load, the floor and the distance

Those three things specify the casters, and the casters are most of the decision. Quotes are reviewed by material handling specialists, typically within one business day.

866-333-0728

Browse carts & trucks at custommhs.com

No bots. No guesswork. Real experts.

Sources

Published caster sizing and push force guidance, including the Liberty Mutual (Snook) tables · CustomMHS product listings for Little Giant, Metro, Jamco, Rousseau, Strong Hold, MECO, Akro-Mils and Bayhead.

Disclaimer. This guide is educational content and reflects the opinion and general experience of CustomMHS. Caster sizing practice and ergonomic force limits are guidance, not regulation. Confirm against the caster manufacturer's ratings and, where you have an ergonomics concern, a qualified assessment. Specifications are subject to change, so confirm before ordering. Reviewed November 2026.