Industrial Equipment Experts Since 1980 | Mon–Fri, 7 AM–6 PM ET
No bots. Real experts. 866-333-0728
Get a Fast Quote
Get a Fast Quote

CustomMHS Buyer's Guide

How to Choose a Service Cart: Steel, Aluminum or Stainless

The material changes how much a cart carries, how it holds up and how hard it is to push for a full shift. Here is how to match the cart to the job.

Written and reviewed by: Tom McGovern, owner of CustomMHSPublished: November 2026Covers: Little Giant · Jamco · MECO · New AgeQuestions: 866-333-0728
Section One

Steel, aluminum or stainless?

Decide by load first, then by environment, then by who pushes it.

Short answer: Choose steel for heavy, dense or awkward loads. Choose aluminum when the cart is moved constantly or the area is humid or washed down. Choose stainless for cleanrooms, food and sterile areas.

Quick answers
  • Steel: Maximum strength. Listed from 600 to 5,000 lb.
  • Aluminum: Lighter and corrosion resistant. Listed from 700 to 2,000 lb.
  • Stainless: For sterile, food and washdown areas.

A service cart is two or three open shelves on casters with a handle. It is the simplest piece of equipment in the plant and one of the most used, which is why the small choices matter: shelf lips, shelf height and above all the casters.

A note on this guide

This guide is written from published manufacturer data and my own experience quoting this equipment. It is general guidance and my opinion, not engineering advice. Confirm the rating for your exact model and application before you order.

Section Two

Steel service carts

The default, and the only choice above 2,000 lb.

Short answer: Steel carts on our site run from 600 lb order picking trucks to 5,000 lb extra heavy duty carts.

Steel service carts by capacity
CapacitySeriesShelves
600 lbMECO OPT order picking truck2
1,000 lbMECO SPT2
1,200 lbJamco ES, SB, LT, SA, SO, NV, SR, LK; Little Giant LGLP perforated2
1,200 lbLittle Giant 3MW; Jamco LN, LO, SC, ST3
1,200 to 2,000 lbLittle Giant LG and LGL; 3LGL2 or 3
2,400 lbJamco SE (2 shelf), SF (3 shelf)2 or 3
3,600 lbLittle Giant 2GL, 2G6W six-wheel, ERGL ergonomic; 3G, 3GL, 3G6W2 or 3
4,000 lbMECO Husky HSC, 12 gauge, 20 configurations2 or 3
4,800 lbJamco SD reinforced2
5,000 lbLittle Giant GH (2 shelf), 3GH (3 shelf)2 or 3

Heavy-duty shelves are commonly 12 gauge. All-welded construction is stiffer than bolted, and bolted carts can loosen over years of use. Choose steel when loads are heavy, dense or awkward, when the cart takes regular impacts, or when stability under load matters most.

Section Three

Aluminum and stainless

Lighter to push, or cleaner to keep.

Short answer: Aluminum trades capacity for weight and corrosion resistance. Stainless is for rooms where the cart itself has to be cleanable.

Aluminum

New Age aluminum carts
CartCapacityNote
2-Shelf Extreme Duty Aluminum Service Cart2,000 lbHighest aluminum capacity listed; corrosion resistant, low maintenance
97769 Heavy Duty Aluminum Utility Cart1,200 lbFor humid or washdown environments
Aluminum Ladder Service Cart 99640800 lbIntegrated ladder for elevated tasks
96134BH Aluminum Utility Stock Truck700 lbLighter duty

Choose aluminum when operators move carts constantly and fatigue matters, or for humid, washdown, coastal or chemical-exposed sites.

Stainless

Stainless carts belong in cleanrooms, labs, food areas and sterile processing. Type 304 is usually sufficient. Type 316 adds molybdenum and resists chlorides, so it is the one for bleach-based cleaning and salt. You will find stainless carts in our cleanroom equipment category rather than with the steel service carts.

Wet area on a steel budget

A perforated steel shelf drains and breathes. The Little Giant LGLP perforated shelf cart is rated 1,200 lb and is listed for wet or washdown use.

Section Four

Shelves: count, lips and height

Small details that decide whether the cart gets used.

Short answer: Two shelves for bulky items, three for more separate loads. Lips up to keep parts on, flush for sliding loads on and off.

  • Count. Two shelves leave more room between shelves for tall items. Three shelves give more separate surfaces.
  • Lips. A retaining lip is typically about 1-1/2 in. It keeps small parts from rolling off. A flush shelf lets you slide a tote or box across. Some picking carts mix both.
  • Deep shelves. The Little Giant DS tray truck has 3, 6 and 12 in. deep shelves for loose or bulk items.
  • Height. A top shelf around 36 in. is a comfortable work height.
  • Size. The Little Giant 3-shelf six-wheel cart runs from 24 x 48 in. to 30 x 72 in. Measure your aisles and doorways before choosing the largest.
Section Five

Casters: the part that decides how it pushes

A cart is only as good as what it rolls on.

Short answer: Rate each caster for one third of the total loaded weight times 1.2, because on an uneven floor only three wheels carry the load.

Worked example

Cart plus load is 3,000 lb. Per caster: (3,000 / 3) x 1.2 = 1,200 lb. Dividing by four would give 750 lb, and the casters would be undersized.

Choosing the wheel
WheelCapacityFloor protectionSuits
PolyurethaneMedium to heavyExcellentSealed and epoxy floors, smooth concrete. The default indoors.
RubberMediumVery goodTile and sealed floors, where floor protection outranks capacity.
PhenolicHeavy dutyPoor, can markHigh temperature, rated to 450°F and above.
Cast iron and steelExtremeNoneFoundries and heavy industrial.
  • Diameter. 4 to 5 in. is the general default. Use 6 in. and up for rough floors.
  • Layout. Two swivel and two rigid track straight. Four swivel turn tightest. Six-wheel carts with four swivel and two rigid do both.
  • Brakes. Specify a total lock brake by name for carts that must not creep.
Section Six

Choosing by application and common mistakes

Find your row, then check the list.

Short answer: Match capacity to the real load, then spend the rest of your attention on casters.

Maintenance rounds, tools and parts
Steel, 1,200 lb class, two shelves with lips.
Order picking
Steel picking truck or cart with flush shelves.
Dies, castings, heavy fixtures
Steel, 3,600 to 5,000 lb.
Long loads on a heavy cart
Six-wheel steel cart, which spreads the load and turns tighter.
Pushed all shift by one person
Aluminum, or steel with larger, better casters.
Humid, coastal or washdown area
Aluminum, or perforated steel.
Cleanroom, lab, food or sterile area
Stainless.
  • Dividing the load by four casters. Use one third times 1.2.
  • Forgetting the cart's weight. The rating includes the cart's own weight.
  • Wheels too small for the floor. Small hard wheels on rough concrete are the top complaint.
  • Wrong shelf edge. Lips stop a tote from sliding on. Flush shelves let parts roll off.
  • Buying more capacity than a person can push. Published ergonomics guidance puts maximum starting force at about 50 lb. A 5,000 lb cart is not a hand cart on a rough floor.

More on carts and casters in our carts, trucks and dollies guide.

Section Seven

Frequently asked questions

The questions I hear most on quote calls.

Should I buy a steel or aluminum service cart?

Choose steel for heavy, dense or awkward loads and regular impacts. Choose aluminum when the cart is moved constantly or used in humid, washdown or coastal areas.

How much weight can a service cart hold?

Steel service carts on our site are listed from 600 to 5,000 lb. Aluminum carts are listed from 700 to 2,000 lb.

When do I need a stainless steel cart?

In cleanrooms, labs, food areas and sterile processing. Use type 316 where bleach-based cleaners or salt are present.

How do I size casters for a cart?

Divide the total loaded weight by three and multiply by 1.2. A 3,000 lb total needs casters rated 1,200 lb each.

Should cart shelves have lips up or be flush?

Lips, typically about 1-1/2 in., keep small parts from rolling off. Flush shelves let you slide totes and boxes on and off.

What is the advantage of a six-wheel cart?

It spreads the load over more wheels and turns in a tighter radius, which helps with long, heavy carts.

About the author. Tom McGovern is the owner of CustomMHS, an industrial material handling distributor serving the US, Canada and Mexico. He has worked in material handling since 1981 and has quoted and specified the Little Giant, Jamco and MECO steel service carts and New Age aluminum service carts and stainless carts sold at CustomMHS. Questions about this guide: 866-333-0728.

Ready for a quote?

Send us these details and a material handling specialist will reply, typically within one business day.

  • Dimensions
    Size of the load and the space it goes in
  • Load
    Weight per item, shelf or level
  • Quantity
    How many units you need
  • Delivery ZIP code
    For freight pricing
  • Drawing
    A sketch, photo or spec sheet, if you have one
Get a Fast Quote Call 866-333-0728

Not sure which cart fits?

Tell us the load, the shelf size you need, the floor and the environment, and we will match a cart and casters. Quote requests are answered within 24 hours by a real person.

866-333-0728

Browse steel and aluminum service carts at custommhs.com

Browse all carts and trucks

Get a fast quote

No bots. No guesswork. Real experts.

Specification sources

CustomMHS carts, trucks and dollies guide and service cart listings · Little Giant, Jamco, MECO and New Age published capacities.

Published figures are current as of November 2026 and are subject to change by the manufacturer. This guide is written from published manufacturer data and my own experience quoting this equipment. It is general guidance and my opinion, not engineering advice. Confirm the rating for your exact model and application before you order.