Industrial Equipment Experts Since 1980 | Mon–Fri, 7 AM–6 PM ET
No bots. Real experts. 866-333-0728
Get a Fast Quote
Get a Fast Quote

CustomMHS Buyer's Guide

How to Size Modular Drawer Cabinets: Drawer Heights, Capacities and Layout

Size the drawer to the part, the cabinet to the drawers and the aisle to the cabinet. Here is the order to work in, with the math in inches.

Written and reviewed by: Tom McGovern, owner of CustomMHSPublished: November 2026Covers: Rousseau R-Series modular drawer cabinetsQuestions: 866-333-0728
Section One

How do you size a modular drawer cabinet?

Work from the smallest thing to the largest: part, drawer, cabinet, aisle.

Short answer: Pick the width from your longest flat item, the drawer heights from your tallest items, the housing height from the drawer stack, and then check the aisle with a drawer fully open.

Quick answers
  • Width: Longest flat item plus 2 in., then the next standard width.
  • Drawer height: Tallest item in that drawer plus about 1 in.
  • Usable drawer stack: Housing height minus about 4 in.
  • Aisle: Cabinet depth plus drawer projection plus 30 in. of working space.
  • Capacity: 400 lb per drawer on the R-Series, with full extension.

The figures in this guide are the published Rousseau R-Series numbers, because that is the line most of our customers build. The method works for any modular drawer cabinet.

A note on this guide

This guide is written from published manufacturer data and my own experience quoting this equipment. It is general guidance and my opinion, not engineering advice. Confirm the rating for your exact model and application before you order.

Section Two

Width and depth

The footprint is set by your longest part and your floor space.

Short answer: R-Series widths are 24, 30, 36, 48, 54 and 60 in. Depths are 18, 21, 24 and 27 in., depending on the width.

R-Series widths and the depths offered
WidthDepthsModel prefix
24 in.21 in., 27 in.R5ACD, R5ACG
30 in.21 in., 27 in.R5ADD, R5ADG
36 in.18 in., 24 in.R5AEC, R5AEE
48 in.24 in., 27 in.R5AHE, R5AHG
54 in.24 in., 27 in.R5AJE, R5AJG
60 in.24 in., 27 in.R5AKE, R5AKG

Width rule. Measure the longest flat item, add 2 in., and buy the next standard width. A 41 in. part needs 43 in., so it goes in a 48 in. cabinet. In a 36 in. drawer it would have to sit diagonally.

Depth. Deeper drawers hold more but need more aisle. Choose depth after you have checked the aisle in section five.

Section Three

Drawer heights and the drawer mix

This is where most of the storage is won or lost.

Short answer: Size each drawer to its tallest item plus about 1 in. Drawer heights run from 3 to 14 in.

Drawer height by contents
ContentsDrawer height
Inserts and taps3 in.
Hand tools4 to 6 in.
Collets5 to 8 in.
Die sets8 to 12 in.
Power tools and PPE10 to 14 in.

A drawer that is too tall wastes the air above the parts. A 60 in. cabinet full of 6 in. drawers holds nine drawers. The same shell with a mix of 3, 4 and 6 in. drawers holds fifteen.

Four published drawer mixes in the same 48 x 24 x 60 in. shell
ModelDrawersCountSuits
R5AHE-5805(10) 3 in., (3) 4 in., (2) 6 in.15Many small part numbers
R5AHE-5813(9) 6 in.9Uniform mid-size items
R5AHE-5807(3) 6 in., (3) 12 in.6Bulky tooling, fixtures, power tools
R5AHE-5822(6) 4 in., (1) 8 in., (1) 10 in., (1) 12 in.9Mixed maintenance stock
Section Four

Cabinet height and capacity

The drawer stack has to fit the housing, and the load has to fit the drawers.

Short answer: Usable drawer height is about the housing height minus 4 in. Every R-Series drawer is rated 400 lb.

Height

Housing heights are 24, 28, 30, 34, 38, 44 and 58 in. The standard 2 in. forklift base adds 2 in., so a 58 in. housing stands 60 in. overall. An optional 4 in. base adds 2 in. more. A 58 in. housing gives about 54 in. of drawer stack.

Check it against a published unit: the R5AHE-5805 has ten 3 in., three 4 in. and two 6 in. drawers. That is 30 + 12 + 12 = 54 in. It fills the housing exactly.

Overall heights of 30 to 40 in. work as bench height. Cabinets 46 and 60 in. tall are storage first.

Capacity

Each drawer is rated 400 lb with full extension and 100 percent access, and the rolling mechanism carries a lifetime warranty. The published R5AEE-5818 (36 x 24 x 60 in., 14 drawers) is rated 5,600 lb total, which is 14 x 400, and weighs 670 lb empty. Add those together when you check the floor.

Anchor tall cabinets

Anchor anything 46 in. or taller, anything with heavy tooling in the upper drawers, and anything in a seismic zone. Specify one-drawer-at-a-time (RB15) on 60 in. units with heavy tooling.

Section Five

Layout: aisle space with a drawer open

A drawer cabinet needs room in front of it that a shelf does not.

Short answer: Aisle needed equals cabinet depth plus drawer projection plus 30 in. of working space.

For a 27 in. deep cabinet the drawer projects about 25 in. The math is 27 + 25 + 30 = 82 in., or about 7 ft from the wall behind the cabinet to the far side of the working space.

Aisle check
Aisle in front of the cabinetResult with a drawer fully open
6 ftA little over 3 ft of passage remains
4 ftThe aisle is blocked

Inside the drawer, partitions and dividers adjust in 1 in. increments. Leave one empty lane at the back of each drawer for part numbers you do not have yet.

Section Six

Common mistakes

All of these are fixed on paper before the order.

Short answer: The usual errors are buying one drawer height throughout, sizing width to the average part, and forgetting the open-drawer aisle.

  • All drawers the same height. Mixed heights can nearly double the drawer count in the same shell.
  • Width sized to the average part. Size to the longest item plus 2 in.
  • Ignoring the aisle. Measure with a drawer fully out.
  • Adding up drawer ratings without checking the floor. 400 lb is the drawer limit. The floor still has to carry the whole cabinet.
  • Choosing the shell before the mix. Two cabinets with the same outside dimensions can differ by well over a thousand dollars depending on the drawer mix. Decide the mix first.

For model numbers, accessories and locks, see our Rousseau R-Series guide. To build your own, use the Rousseau configurator.

Section Seven

Frequently asked questions

The questions I hear most on quote calls.

How do I choose the width of a modular drawer cabinet?

Measure your longest flat item, add 2 in., and buy the next standard width. Rousseau R-Series widths are 24, 30, 36, 48, 54 and 60 in.

What drawer heights are available?

Rousseau R-Series drawers run from 3 to 14 in. high. Common heights are 3, 4, 5, 6, 7, 8, 9, 10, 12 and 14 in.

How much weight can a modular cabinet drawer hold?

Every Rousseau R-Series drawer is rated 400 lb with full extension. Light-duty series are rated 100 lb per drawer.

How many drawers fit in a 60 in. tall cabinet?

It depends on the mix. A 58 in. housing has about 54 in. of drawer stack. Published 48 x 24 x 60 in. units range from 6 drawers to 15 drawers.

How much aisle space does a drawer cabinet need?

Cabinet depth plus drawer projection plus 30 in. of working space. For a 27 in. deep cabinet that is about 82 in., or roughly 7 ft.

Do modular drawer cabinets need to be anchored?

Anchor cabinets 46 in. or taller, cabinets with heavy tooling in upper drawers, and cabinets in seismic zones.

About the author. Tom McGovern is the owner of CustomMHS, an industrial material handling distributor serving the US, Canada and Mexico. He has worked in material handling since 1981 and has quoted and specified the Rousseau R-Series modular drawer cabinets and storage cabinets sold at CustomMHS. Questions about this guide: 866-333-0728.

Ready for a quote?

Send us these details and a material handling specialist will reply, typically within one business day.

  • Dimensions
    Size of the load and the space it goes in
  • Load
    Weight per item, shelf or level
  • Quantity
    How many units you need
  • Delivery ZIP code
    For freight pricing
  • Drawing
    A sketch, photo or spec sheet, if you have one
Get a Fast Quote Call 866-333-0728

Want us to lay out the drawers?

Send us a list of what you are storing with rough sizes and weights, and we will propose a cabinet and drawer mix. Quote requests are answered within 24 hours by a real person.

866-333-0728

Browse Rousseau R-Series drawer cabinets at custommhs.com

Build a cabinet in the Rousseau configurator

Get a fast quote

No bots. No guesswork. Real experts.

Specification sources

CustomMHS Rousseau R-Series guide, cabinets guide and product listings · Rousseau published R-Series specifications.

Published figures are current as of November 2026 and are subject to change by the manufacturer. This guide is written from published manufacturer data and my own experience quoting this equipment. It is general guidance and my opinion, not engineering advice. Confirm the rating for your exact model and application before you order.