Industrial Equipment Experts Since 1980 | Mon–Fri, 7 AM–6 PM ET
No bots. Real experts. 866-333-0728
Get a Fast Quote
Get a Fast Quote

CustomMHS Buyer's Guide

Rousseau R-Series Stationary Drawer Cabinets

Every R-Series cabinet is described by a model number that tells you the width, the depth, the housing height and the drawer mix. Learn to read it and the rest of the specification falls into place.

Covers: Rousseau R-Series stationary modular drawer cabinets Questions: 866-333-0728 Written and reviewed by: Tom McGovern · November 2026
Section One

What the R-Series is built to do

A 400 lb per drawer stationary cabinet, and the problem it solves.

Quick answers
  • Every Rousseau R-Series drawer is rated at 400 lb and opens to 100% extension, with a lifetime warranty on the drawer rolling mechanism.
  • The model number tells you the cabinet: R5AHE-4401 is 48 in wide, 24 in deep, with a 44 in drawer housing that stands 46 in tall on its base.
  • Widths are 24, 30, 36, 48, 54 and 60 in. Pick the width from the longest item that has to lie flat, not from the wall you want to fill.
  • Anchor any cabinet 46 in or taller, and load the heavy drawers low.

The Rousseau R-Series is the company's heavy-duty stationary modular drawer cabinet. Every drawer carries a 400 lb rating and rides on full-extension slides, so the back of the drawer is as reachable as the front. Rousseau backs the drawer rolling mechanism with a lifetime warranty.

That matters because cheap drawer storage does not fail at the box. It fails at the slide. A drawer loaded with die sets that binds or sags is a drawer nobody uses, and the contents drift back onto a shelf or a bench.

Where the density comes from

Shelving stores parts at whatever spacing the shelves are set to, and everything above the part is wasted air. A drawer cabinet sets the height per drawer, in inches. The R5AHE-5805, a 48 in × 24 in × 60 in cabinet, has ten 3 in, three 4 in and two 6 in drawers: fifteen separately organized layers in one footprint.

The trade is cost. Drawer storage pays for itself on small, valuable, frequently used items with many part numbers. If you are storing cartons of consumables, buy shelving.

Where this guide sits

This guide covers the Rousseau R-Series only. For drawer cabinets versus enclosed cabinets, steel gauge, flammable storage and cylinder cages, see the Cabinets and Modular Drawer Storage guide. To see configurations and pricing, go to Rousseau R-Series cabinets. If the cabinet has to travel to the machine, you want a modular drawer cart, and the drawer advice here still applies.

Please read this part

This guide is educational and reflects the opinion and general experience of CustomMHS as a Rousseau dealer. It is not engineering advice. Dimensions, weights, configurations and part numbers change, so confirm them on the product listing or your quote before ordering. Floor loading and anchoring should be verified for your building.

Section Two

Reading an R-Series model number

The most useful skill for buying this line. Once you can read it, you can compare quotes.

Short answer: After the R5A prefix, the next letter is the width, the next is the depth, the first two digits are the drawer housing height in inches, and the last two digits are the drawer mix.

R5A   H   E   -   44   01
R5A
Standard R-Series stationary cabinet
H
Width code: H is 48 in
E
Depth code: E is 24 in
44
Drawer housing height in inches. The 2 in base brings the overall height to 46 in
01
Configuration number: which drawer mix

So the R5AHE-4401 is a 48 in wide, 24 in deep cabinet listed at 46 in tall, with two 3 in, two 4 in, three 6 in and one 8 in drawer.

Width and depth codes seen on our R-Series listings
Code As the width (4th character) As the depth (5th character)
C 24 in 18 in
D 30 in 21 in
E 36 in 24 in
G Not used 27 in
H 48 in Not used
J 54 in Not used
K 60 in Not used

Position matters. The same letter means one thing as a width and another as a depth: E is 36 in wide in the fourth position and 24 in deep in the fifth. R5ADG is 30 in wide by 27 in deep. R5AEE is 36 in wide by 24 in deep.

The height digits

The first two digits after the dash are the drawer housing height. On our 48 in listings the overall height is that number plus 2 in for the base: a -30 cabinet is listed at 32 in, a -38 at 40 in, a -44 at 46 in and a -58 at 60 in.

Check the listed height, do not compute it

Some listings show the housing height and some show the overall height. Use the code to sort and compare models, and take the overall height from the listing or the quote before you commit to a spot under a mezzanine or a duct.

The configuration digits and the suffix

The last two digits identify the drawer mix. When you compare prices between suppliers, compare the full model number, not just the size and the drawer count. Some models carry a suffix such as -ST055, which marks a standard-color configuration. Confirm the color and lead time on the listing.

Section Three

Choosing width

Six standard widths. The right one depends on what goes in the drawer, not the wall you are filling.

Short answer: Measure the longest item that has to lie flat, add 2 in, and buy the first standard width that clears it.

The R-Series comes in 24, 30, 36, 48, 54 and 60 in widths. In a single column cabinet each drawer spans the full width.

R-Series widths
Width In our experience it suits Listing
24 in A tight spot beside a bench. Fasteners, small hand tools, inserts and gauges. 24 in cabinets
30 in Tool cribs, maintenance stations and work cells. 30 in cabinets
36 in A general tool room. A full socket and wrench set fits one drawer with partitions. 36 in cabinets
48 in Heavy tooling, with the most drawer mixes to choose from. 48 in or 48 in multi-drawer
54 in Long tooling and fixture sets. 54 in or 54 in multi-drawer
60 in Oversized components and complete kits stored flat. 60 in or 60 in multi-drawer

In 48, 54 and 60 in widths you can also choose a multi-drawer cabinet, which divides the same footprint into two columns of drawers. Two columns let you set different drawer heights on each side.

The test

Storing a 41 in part on the diagonal in a 36 in drawer works once. Then somebody stands it on end and it stops being findable. A 41 in part plus 2 in is 43 in, so it needs the 48 in cabinet.

A wide drawer with nothing in it is a sliding table. Parts drift to the back every time it closes. Plan partitions for any drawer 48 in or wider. If the budget will not carry them, buy the narrower cabinet.

Section Four

Choosing depth

Four depths, and the one that decides whether the aisle still works.

Short answer: Take the 24 in depth unless your parts need 27 in, and check that the aisle can take a fully open drawer plus a person.

Depths by width, from the model codes on our listings
Width Depths Model prefixes
24 in 21 in, 27 in R5ACD, R5ACG
30 in 21 in, 27 in R5ADD, R5ADG
36 in 18 in, 24 in R5AEC, R5AEE
48 in 24 in, 27 in R5AHE, R5AHG
54 in 24 in, 27 in R5AJE, R5AJG
60 in 24 in, 27 in R5AKE, R5AKG

Depth is an aisle decision

Because the drawers open to 100% extension, an open drawer sticks out about as far as the cabinet is deep. Then a person has to stand at it.

Worked example: how much aisle, in feet and inches
  • Formula: cabinet depth + open drawer + room for a person. Allow 30 in for the person.
  • 27 in deep cabinet: 27 + 27 + 30 = 84 in, or 7 ft from the wall behind the cabinet.
  • 24 in deep cabinet: 24 + 24 + 30 = 78 in, or 6 ft 6 in.
  • 18 in deep cabinet: 18 + 18 + 30 = 66 in, or 5 ft 6 in.
  • Two rows facing each other: add the second cabinet's depth if only one drawer is open at a time, and more if both sides work at once.

The extra 3 in between a 24 in and a 27 in cabinet is real storage, 12-1/2 percent more drawer area, but it is the hardest space in the cabinet to reach and you pay for it on every drawer. Take the deeper cabinet when the parts need it.

Section Five

Height, and what the base is doing

The base is a handling decision that looks like a dimension.

Short answer: Cabinets 32 to 40 in tall work as a bench. Cabinets 46 and 60 in tall are for storage. Order the 4 in base if the cabinet may ever be moved.

On our 48 in listings, overall heights are 32, 40, 46 and 60 in. The drawer stack inside is shorter than the housing: on those models the drawer heights add up to 4 in less than the housing height.

Worked example: check a quote by adding the drawers
  • R5AHE-5805, 58 in housing: (10 × 3) + (3 × 4) + (2 × 6) = 54 in of drawers.
  • R5AHE-4401, 44 in housing: (2 × 3) + (2 × 4) + (3 × 6) + 8 = 40 in of drawers.
  • R5AHE-3001, 30 in housing: (2 × 3) + (3 × 4) + 8 = 26 in of drawers.
  • Rule of thumb: drawer heights should add up to the housing height less 4 in.

Standard

2 in forklift base

The base the listed overall heights assume. It lets the cabinet be lifted from the front with forks.

Optional

4 in base

Adds 2 in to the overall height. Ask for it if the cabinet may be moved after installation, since it gives more ways to get forks or a pallet jack under it. Confirm the access on your quote.

Cabinets from 32 to 40 in put the top at or near working height, which is why they pair with a work surface. The 46 in and 60 in cabinets are storage first. The top of a 60 in cabinet is 5 ft off the floor, too high to work on.

Load heavy drawers low

A 60 in cabinet with 400 lb drawers can tip when a loaded top drawer is fully open. Put dies and fixture plates in the bottom drawers, and read section eleven on anchoring before a tall cabinet is placed.

Section Six

Building the drawer mix

The decision that determines whether the cabinet earns its price.

Short answer: Size each drawer to the tallest item it holds plus about 1 in, and buy the number of drawers you will really use. More drawers cost more in the same shell.

Once width, depth and height are fixed, the remaining choice is how to divide the housing into drawers. A fixed height can be divided many ways, and the number of drawers decides how many kinds of inventory the cabinet can keep apart.

Same 48 in × 24 in × 60 in cabinet, different drawer mixes
Model Drawer mix Drawers In our experience it suits
R5AHE-5805 Ten 3 in, three 4 in, two 6 in 15 Many small part numbers: inserts, taps, fasteners, gauges
R5AHE-5801 One 3 in, one 5 in, two 6 in, two 7 in, one 8 in, one 12 in 8 Mixed tooling with a few tall items
R5AHE-5857 Four 3 in, three 4 in, two 5 in, one 6 in, plus a shelf 10 and a shelf Small tooling plus bulky items on the shelf

The fifteen-drawer cabinet costs more than a cabinet with fewer drawers in the same shell, because you are buying more slides. That is worth paying when it buys separation you will use.

How to size a drawer

Inserts, taps, drills, small gauges
3 in drawers, partitioned tightly.
Hand tools, wrenches, sockets
4 in to 6 in drawers with partitions and dividers.
Collets and toolholders
5 in to 8 in drawers with collet foam. The tallest holder standing upright sets the height.
Die sets, fixture plates, heavy blanks
8 in to 12 in drawers, in the bottom third of the cabinet.
Power tools in cases, PPE, kits
The tallest drawers, or a shelf section.

The instinct to round up is expensive. Every extra inch of drawer height is an inch that cannot become another drawer.

Section Seven

Partitions, dividers and groove trays

The system that turns a steel box into organized storage.

Short answer: Partitions split a drawer into lanes and dividers split each lane. Order mixed-content drawers with them, since adding them later means a second order and a second freight charge.

Rousseau's compartment system has two parts that work together. Partitions are the long separators that divide the drawer into lanes. Dividers sit between the partitions and split each lane. Both are removable and can be moved as your inventory changes.

R-Series compartment parts, as named in Rousseau accessory data
Part What it is Use it for
RG00 Front-to-back partition The default. Divides the drawer into lanes.
RG01 Left-to-right partition Long parts and tools that will not fit front to back.
RG10 Drawer divider Splits a lane into compartments.
RG35 and RG36 Groove trays, front-to-back and left-to-right Small parts that need a defined seat.
RG39 Groove tray divider Splits a groove tray.

Laying out a drawer

  1. Set the partition spacing from the widest item in each group.
  2. Set the dividers in each lane from the length each item needs.
  3. Size compartments with a little clearance, since the separators take up some width.
  4. Leave one lane empty at the back of a mixed drawer. New part numbers arrive, and a layout with no slack gets abandoned.

Skip partitions in drawers that will be foamed, drawers holding one uniform item, and drawers holding cased power tools.

Section Eight

Liners, foam and tool protection

Cheap on the order, costly to add later.

Short answer: Put a liner in every drawer. Use cut tool foam only for tooling you have to account for, and collet foam for collets and toolholders.

A bare steel drawer bottom lets parts slide every time the drawer opens, and it marks precision surfaces. Our R-Series listings show these options:

Liner and foam options
Option Use it for
PVC drawer liner Basic protection for the drawer bottom and the parts on it. The default for hand tool and parts drawers.
Foam drawer liner Cushioning for finished parts, gauges and instruments.
RG42 foam tool protection Cut foam that holds each tool in its own pocket, so a missing tool shows at a glance.
RG43 foam for collets Seats that hold collets and toolholders upright and apart.
Tool foam pays for itself in audits

Tool foam is the difference between "we think all the tools came back" and seeing it from six feet away. Foam the drawers that hold controlled tooling and skip it everywhere else.

Section Nine

Tops, doors and side panels

Turning storage into a station.

Short answer: A bench-height cabinet with a top replaces a separate workbench. Choose the top by the work: butcher block for assembly, steel for impact, stainless for washdown.

A bench-height R-Series cabinet with the right top becomes a work surface with 400 lb drawers under it. The Rousseau counter height work center is built for exactly that.

R-Series top options on our listings
Top Choose it when
Butcher block General assembly and bench work.
Steel with non-slip rubber mat Heavy work where the surface takes impact and parts still need cushioning.
Galvanized steel Durability first.
Stainless steel, or marine edge stainless steel Food, pharmaceutical, lab and washdown areas. The marine edge contains spills.
Slope top Against a wall where clutter would otherwise collect on the cabinet.

Some configurations replace part of the drawer stack with a shelf or a door section, such as the R5AHE-5857 with its shelf. That handles the bulky items no drawer height suits. Rousseau also offers side panels for hooks and bins. Ask us what fits your model.

Section Ten

Locks, security and drawer safety

Two different problems that use the same options list.

Short answer: Decide the keying before you order, and on tall cabinets with heavy tooling ask for the option that lets only one drawer open at a time.

R-Series lock and safety options, as named in Rousseau accessory data
Part What it does Fits
L3 Key lock The usual choice. Only as good as your key control.
L50 Code lock Shared cabinets where issuing keys is the burden.
L100 Electronic access Controlled tooling where you want access you can take away.
LP Safety hasp Takes a padlock. Also your lockout point.
RB10 Vertical security bar Added security across the drawer fronts.
RB15 One drawer at a time Keeps a second drawer from opening while one is out.
Confirm part numbers on your quote

The part numbers in this guide come from Rousseau's accessory data and can change. We confirm each one on the quote.

Decide keying before you order

Keyed alike, keyed differently or master keyed costs nothing to specify and is a nuisance to change. Several cabinets in one crib usually want keyed alike with a master. Cabinets holding high-value tooling want keyed differently. Say which on the purchase order.

Section Eleven

Freight, siting and anchoring

The steps between the purchase order and a working cabinet.

Short answer: Plan for a forklift or a liftgate at delivery, check the floor rating on a mezzanine, and anchor any cabinet 46 in or taller.

Weight

R-Series cabinets weigh several hundred pounds before they hold anything, and each drawer can add up to 400 lb. Fifteen drawers at 400 lb is 6,000 lb of rated drawer capacity in one 48 in × 24 in footprint, which is 8 square feet.

  • Delivery. These ship on pallets and need a forklift, or a liftgate and a pallet jack, at the receiving end. Settle that before the truck arrives.
  • Floor loading. On a slab this is rarely an issue. On a mezzanine, a raised floor or an upper story, have the loaded weight checked against the floor rating first.

Anchoring

Anchor any cabinet 46 in or taller, and load heavy drawers low to reduce the tipping risk. The tipping case is a loaded upper drawer at full extension with somebody leaning on it. Also anchor in a seismic zone whatever the height, and get engineering input where the slab is questionable.

Placement and lead time

Leave the aisle worked out in section four. Put the cabinets that get opened most nearest the door. If a project date is fixed, ask for the lead time in writing at the quote stage. A standard configuration in a standard color is the safer choice for a deadline.

Section Twelve

Common and costly mistakes

What goes wrong on R-Series orders.

Short answer: Most regrets come from choosing width by the wall, forgetting the aisle, and comparing quotes by size instead of by full model number.

  • Choosing width from the wall, not the parts. The longest item that has to lie flat sets the width.
  • Ignoring the aisle. Drawers open their full depth. A correct cabinet in an aisle that is too narrow never gets fully opened.
  • Computing overall height from the model number. The two digits are the housing height. Take the overall height from the listing.
  • Buying the most drawers by reflex. Buy the separation you will use.
  • Rounding drawer heights up. Every wasted inch could have been part of another drawer.
  • Cutting the partitions to hit a number. An open 48 in drawer of mixed parts is a sliding table.
  • Loading heavy drawers high. Dies and fixture plates belong in the bottom third.
  • Skipping anchoring on tall units. Anchor anything 46 in or taller.
  • Not deciding keying at order time.
  • Comparing quotes on dimensions alone. Two cabinets the same size can differ widely in price depending on the drawer count. Compare full model numbers.
Section Thirteen

Frequently asked questions

The questions that come up most often on R-Series quotes.

What does the R-Series model number mean?

Reading left to right: R5A is the standard R-Series stationary cabinet. The fourth character is the width code and the fifth is the depth code. The first two digits after the dash are the drawer housing height in inches, and the last two digits identify the drawer mix. So R5AHE-4401 is 48 in wide and 24 in deep with a 44 in housing, listed at 46 in tall.

Is every R-Series drawer rated at 400 lb?

Yes. The R-Series is listed at 400 lb per drawer, with 100% drawer extension and a lifetime warranty on the modular drawer rolling mechanisms. The rating is per drawer, not for the cabinet as a whole, so anchor tall cabinets and load the heavy drawers low.

What widths and depths are available?

Widths are 24, 30, 36, 48, 54 and 60 in. Depths on our listings are 18, 21, 24 and 27 in, but not every depth comes in every width. The 24 and 30 in widths come 21 or 27 in deep, the 36 in width comes 18 or 24 in deep, and the 48, 54 and 60 in widths come 24 or 27 in deep.

Why do two cabinets with the same dimensions have different prices?

Usually the drawer count. In a 48 in by 24 in by 60 in shell, the R5AHE-5805 has fifteen drawers and the R5AHE-5801 has eight. You are buying drawers and slides, not just steel. Compare the full model number, including the last two digits.

Should I order the drawers partitioned or add compartments later?

Order them with partitions unless the drawer will hold foam or one uniform item. Partitions and dividers can be moved later. Adding them afterward means a second order and a second freight charge.

What is the difference between the 2 in and 4 in base?

The 2 in forklift base is standard and is what the listed overall heights assume. The optional 4 in base adds 2 in to the overall height and makes the cabinet easier to pick up and move. If the cabinet may be relocated, ask for it on the quote.

Do R-Series cabinets need to be anchored?

Anchor any cabinet 46 in or taller, and load heavy drawers low to reduce the tipping risk. Also anchor in a seismic zone whatever the height.

How much aisle do I need in front of an R-Series cabinet?

Allow the cabinet depth, plus the same again for the open drawer, plus about 30 in for a person. For a 27 in deep cabinet that is 84 in, or 7 ft, from the wall behind the cabinet. For a 24 in deep cabinet it is 6 ft 6 in.

What does a suffix like -ST055 mean?

It marks a standard-color configuration. Choosing one avoids the cost and schedule risk of a custom finish. Confirm the color and the lead time on the listing or the quote.

Can an R-Series cabinet be used as a workbench?

Yes, in the bench-height configurations. Top options on our listings include butcher block, steel with a non-slip rubber mat, galvanized steel, stainless steel, marine edge stainless steel and a slope top. Rousseau also makes a counter height work center.

What about mobile versions?

Rousseau builds the same drawers on cart frames. The width, depth and drawer mix advice in this guide carries over, and the anchoring and aisle advice changes. If the storage has to travel to the machine, ask about a modular drawer cart.

Section Fourteen

Quick-reference tables

Everything above, condensed.

Published R-Series figures
Specification Published figure
Drawer capacity 400 lb per drawer
Drawer extension 100% drawer extension, full-extension slides
Widths 24, 30, 36, 48, 54, 60 in
Depths 18, 21, 24, 27 in, depending on width
Overall heights on 48 in listings 32, 40, 46, 60 in
Drawer heights on 48 in listings 3, 4, 5, 6, 7, 8 and 12 in
Columns Single column, or two columns (multi-drawer) in 48, 54 and 60 in widths
Warranty Lifetime on the modular drawer rolling mechanisms
Anchoring Anchor any cabinet 46 in or taller
Model number decoder
Position Meaning Values
Characters 1 to 3 Series R5A, standard R-Series stationary cabinet
Character 4 Width C is 24, D is 30, E is 36, H is 48, J is 54, K is 60 in
Character 5 Depth C is 18, D is 21, E is 24, G is 27 in
First two digits Housing height Add the base for overall height. Check the listing.
Last two digits Configuration The drawer mix
Suffix Stock unit For example -ST055, a standard-color configuration

Specify-it checklist

1. Longest item lying flat
Sets the width. Add 2 in and take the next standard width.
2. Aisle available
Sets the deepest cabinet you can use. Cabinet depth, plus the same again, plus 30 in.
3. Ceiling, duct or mezzanine clearance
Sets the height. Take the overall height from the listing.
4. Tallest item in each group
Sets each drawer height. Item height plus about 1 in.
5. Mixed contents in any drawer?
Order partitions and dividers for it.
6. Precision or controlled tooling?
Tool foam and collet foam.
7. Will anyone work on top of it?
Add a top. Bench-height configurations only.
8. Who needs access?
Pick the lock, and state the keying on the purchase order.
9. Cabinet 46 in or taller?
Anchor it, and ask for the one-drawer-at-a-time option.
10. Might it move later?
Ask for the 4 in base.

About the author. Tom McGovern has worked in the industrial material handling industry since 1981, bringing over 45 years of hands-on experience helping businesses select the right equipment for their applications. His expertise includes specifying and quoting Rousseau R-Series drawer cabinets in 36 in, 48 in and 60 in widths and the counter height work center.

Questions about this guide? Call 866-333-0728 to speak with an experienced material handling specialist.

Ready for a quote?

Send us these details and a material handling specialist will reply, typically within one business day.

  • Dimensions
    Size of the load and the space it goes in
  • Load
    Weight per item, shelf or level
  • Quantity
    How many units you need
  • Delivery ZIP code
    For freight pricing
  • Drawing
    A sketch, photo or spec sheet, if you have one
Get a Fast Quote Call 866-333-0728

Send us the drawer list

Tell us what goes in each drawer, the tallest item in each group, the longest item that has to lie flat, and the aisle you have. We will build the drawer mix and quote the model number. Quotes are reviewed by material handling specialists, typically within one business day.

866-333-0728

Browse Rousseau R-Series stationary drawer cabinets

No bots. No guesswork. Real experts.

Sources

Rousseau Metal published R-Series product and accessory data · CustomMHS Rousseau R-Series product listings.

Disclaimer. This guide is educational content and reflects the opinion and general experience of CustomMHS. It is not a compliance assessment or engineering advice. Dimensions, weights, configurations, part numbers, lead times and pricing change, so confirm current specifications on the product listing or quote before ordering. Floor loading and anchoring should be verified for your building. Reviewed November 2026.