Industrial Equipment Experts Since 1980 | Mon–Fri, 7 AM–6 PM ET
No bots. Real experts. 866-333-0728
Get a Fast Quote
Get a Fast Quote

CustomMHS Buyer's Guide

Ladders & Work Platforms

The rating on a ladder is not the user's body weight. It is the person plus everything they carry, and that one misunderstanding puts more people over the limit than anything else in this category.

Covers: Ballymore · Cotterman · EGA Questions: 866-333-0728 Written and reviewed by: Tom McGovern · November 2026
Section One

The number people misread

Ask what a 300 lb ladder rating means and most people say it holds a 300 lb person. It does not.

Quick answers
  • A ladder's load rating covers the person plus clothing, tools and whatever they carry. OSHA calls this the maximum intended load.
  • A 200 lb worker with protective gear, a tool belt and a 25 lb case is a 260 lb load.
  • OSHA 1910.23(e) limits the stair slope on mobile ladder stands to 60 degrees and calls for handrails once the top step is 4 ft or higher.
  • A 50 degree walk-down ladder lets people come down facing forward. On a 10 ft climb it needs about 2 ft 5 in more floor length than a 59 degree ladder.

OSHA defines maximum intended load in 1910.21(b) as the total load, weight and force, of the employee and all tools, equipment and materials being carried. So the question is not whether the person weighs less than the rating. It is everything that goes up the ladder.

Body weight + clothing and protective gear + tool belt + tools in hand + materials = the load that must stay under the rating
Worker
200 lb
Boots, coveralls, hard hat
About 10 lb
Loaded tool belt
About 25 lb
Case of parts
25 lb
Total
260 lb

That worker is over a 250 lb rating and does not feel heavy. Nothing signals it. The ladder does not sag, and the rating label is at the bottom where nobody is looking.

The practical fix

Buy more capacity than your arithmetic says you need. The price step between ratings is small next to the cost of the ladder, and it covers the tool belt, the box of parts and the heavier worker without anyone doing math at the bottom of a ladder.

Please read this part

This guide is educational and reflects the opinion and general experience of CustomMHS as an equipment distributor. It is not a compliance assessment or legal advice. Ladders are governed by OSHA 1910.23 in full, with related rules in 1910.28, 1910.29 and 1910.30. Load ratings and dimensions are the manufacturers' published figures. Confirm the current data sheet for your exact model before you order.

Section Two

Load ratings and duty types

Two rating systems show up in this category. Know which one you are reading.

Short answer: Portable ladders carry an ANSI duty type from 200 lb to 375 lb. Rolling ladders and platforms publish a load capacity in pounds. Read both as the person plus everything carried.

ANSI duty ratings for portable ladders
Type Duty Rated load
Type IAA Special duty 375 lb
Type IA Extra heavy duty 300 lb
Type I Heavy duty 250 lb
Type II Medium duty 225 lb
Type III Light duty 200 lb

The numbering runs backwards. Type III is the lightest and Type IAA is the heaviest. Types IA and IAA are easy to confuse, and there is 75 lb between them.

For plant and warehouse work, 300 lb is a sensible floor and 375 lb is worth it wherever people carry tools or materials up. Types II and III are commercial and household ratings.

Rolling safety ladders, stock picking ladders and work platforms are sold with a load capacity stated on the listing. Find that number for the exact model and compare it to the total from section one.

The rating is for the whole unit

A load rating describes what the ladder supports as a unit. It is not a rating per step. One person at a time, unless the equipment is specifically designed and rated for more.

Section Three

What makes a ladder industrial

The difference between a rolling safety ladder and a stepladder is not just size.

Short answer: Look for deep steps, handrails on both sides, a top platform, and casters that cannot roll once someone is on the ladder. Then pick the tread for your floor conditions.

Underfoot

Deep, slip-resistant steps

A step you stand on with your whole foot, so climbing is a walking motion. OSHA 1910.23(e) calls for slip-resistant steps with a rise of not more than 10 in and a depth of not less than 7 in on mobile ladder stands.

Hands

Handrails on both sides

Three points of contact only works if there is something to hold. Handrails let a person climb facing forward with a natural stride.

Top

A platform to stand on

A platform with rails turns the top of the ladder into a place to work with both hands.

Base

Casters that hold under load

Easy to move when empty, fixed in place when occupied. Section eight covers how.

Choose the tread for the conditions

Tread types on our rolling ladder listings
Tread How it works Where it fits
Expanded metal Open pattern lets dirt and debris fall through Warehouses and distribution, the general-purpose choice
Perforated Smoother surface with small openings Retail, stockrooms and cleaner back-of-house areas
Grip strut or serrated grating Serrated bars bite into the boot sole and the open grid drains water and oil Wet, greasy or icy conditions and docks

See the tread options on steel rolling safety ladders from Ballymore and Cotterman.

Stock picking ladders

Stock picking ladders are built for people who go up and down all day pulling orders or stocking shelves. If your people are on and off a ladder constantly, start here instead of a general-purpose rolling ladder.

Section Four

Climbing angle

A spec most buyers never look at, and the one that decides whether people will use the ladder properly.

Short answer: OSHA caps mobile ladder stand stairs at 60 degrees. A 50 degree walk-down ladder is easier and safer to descend, and it costs floor space.

OSHA 1910.23(e) says the slope of the step stringer on a mobile ladder stand or platform must not be more than 60 degrees, measured from the horizontal. That is the steepest allowed, not the most comfortable.

Standard versus walk-down
Angle What it is like Trade-off
About 58 to 60 degrees The conventional rolling ladder. You climb it with your hands on the rails and come down facing the steps. Shortest footprint for the height
50 degrees Close to a stairway. You can come down facing forward and carry something in one hand. Longer base

Worked example: how much floor the angle costs

The horizontal run of the stairs is the height divided by the tangent of the angle. For a 10 ft climb:

Stair run for a 10 ft climb
Angle Math Stair run
59 degrees 10 ft ÷ 1.664 About 6 ft 0 in
50 degrees 10 ft ÷ 1.192 About 8 ft 5 in
Difference About 2 ft 5 in longer

That is the stair portion only. The full base is longer on both, so use the overall length on the listing for aisle planning. On a 6 ft climb the difference is about 1 ft 5 in.

When to pay for the floor space

  • People climb often, so the effort adds up.
  • People carry things up and down and cannot keep both hands on the rails.
  • Coming down is the problem. A steep ladder makes people turn and back down, and that is where falls happen.

Stay with the standard angle where floor space is tight and the ladder is used now and then. See 50 degree walk-down rolling ladders.

Section Five

Platforms and the height thresholds

Two heights in the OSHA rule change what the equipment must have. Know them before you compare quotes.

Short answer: Handrails start at a 4 ft top step. Above 10 ft, mobile platforms need guardrails and toeboards. Make sure both quotes include the same protection.

What OSHA 1910.23(e) calls for by height
Height Requirement
Top step 4 ft or higher Handrails 29-1/2 in to 37 in high, measured from the front edge of the step
Ladder stand, top step above 10 ft Top step protected on three sides by a handrail at least 36 in high. A top step 20 in or deeper also gets a midrail and toeboard
Platform 4 ft to 10 ft high Handrails at least 36 in high and midrails in the platform area
Platform above 10 ft high Guardrails and toeboards on the exposed sides and ends of the platform

This matters when you compare prices. A quote for an 11 ft platform without the full guardrail system is not the same product as one with it. If two quotes at similar heights are far apart, check what protection each includes.

Worked example: base width and height

1910.23(e) also limits the work surface height to four times the shortest base dimension unless the unit has added support such as outriggers or counterweights. A base 30 in wide is 2 ft 6 in, and 4 × 2 ft 6 in = 10 ft. A taller unit on that base needs the added support. This is why tall rolling ladders get wide.

Work platforms

When the job is standing and working, not climbing to reach something, a platform is the right tool. A single entry work platform gives a stable raised work surface with one way on and off. A one-step adjustable height platform gives quick access for short-reach tasks.

The one-step case deserves attention. A lot of climbing on pallets, boxes and chairs happens because the task is 12 in to 18 in out of reach and fetching a ladder feels like too much. A small platform parked at the task removes the temptation.

A short fall is still a fall

A fall from 4 ft onto concrete can cause a serious injury. The point of a low platform is to make the safe option the convenient one.

Section Six

Reaching over obstacles

Two formats for the job where a normal ladder cannot get close enough.

Short answer: Use a cantilever ladder to work over a machine or tank, and a crossover to get people across a conveyor or pipe run.

Cantilever ladders

The platform extends out past the base, so it can sit over equipment without touching it. The use is maintenance access over a machine, a tank, a conveyor, or anything you cannot roll a ladder base up against. Because the load sits outside the footprint, the base is larger and heavier than the reach alone suggests. Plan where it will be stored. See Ballymore steel cantilever ladders.

Crossover ladders and platforms

Stairs up, a platform across and stairs down, so people cross over a conveyor or pipe run instead of climbing over it or crawling under it. In a plant with conveyor lines this is one of the most valuable safety purchases, because the walk around is long and the climb over looks easy.

Portable or fixed crossover
Choose portable when Choose fixed when
The line layout changes The obstacle is permanent
You need the crossing in different places The crossing point is settled and used all day
You want to test a location first You want the most stable, permanent answer

See Cotterman portable crossover ladders and Ballymore fixed crossover platforms. If you are unsure where people will cross, place a portable unit, watch where it gets used, then install a fixed one there.

Section Seven

Steel, aluminum or stainless

Three materials. The deciding factor is usually how often the ladder moves.

Short answer: Steel is the default, aluminum is for ladders that move many times a day, and stainless is for washdown.

Steel

The default

Strong, durable, cost-effective and heavy. Right where the ladder stays in one area and gets hard use.

Aluminum

For frequent moves

Light and corrosion resistant. If people move the ladder many times a day, weight is the spec that matters. See aluminum rolling ladders.

Stainless

For washdown

For food, pharmaceutical and other areas that are cleaned hard. See Ballymore stainless steel ladders and our cleanroom and stainless guide.

Weight is a safety spec

The most common unsafe act on a ladder is leaning out sideways instead of climbing down and moving it 3 ft. Every pound you take out of the ladder makes the safe move more likely.

Section Eight

Casters and how they lock

A rolling ladder has to roll freely and then not roll at all.

Short answer: Spring-loaded casters retract under a person's weight so the ladder sits on its feet. Manual locks work only if someone sets them. Never move a ladder with a person on it.

OSHA 1910.23(e) requires the wheels or casters to have a system that impedes horizontal movement when a person is on the unit, and it prohibits moving a mobile ladder stand or platform while it is occupied. Manufacturers meet the first part two ways:

  • Spring-loaded casters. Empty, the ladder rides on the casters and rolls. When a person steps on, their weight compresses the springs and the ladder settles onto rubber-tipped feet. Nobody has to remember anything. Check that the springs and feet are in good condition.
  • Manual locks or brakes. The user sets a lock before climbing. Simple and positive, and it depends on someone doing it every time.

The floor matters

Either design is only stable if every contact point meets the floor. Uneven, broken or sloped concrete defeats both. If a ladder rocks in one spot, look at the floor before you blame the ladder.

Section Nine

The OSHA requirements in one place

29 CFR 1910.23 covers ladders. These are the provisions that bear on choosing and using this equipment.

Short answer: Know the load definition, the per-shift inspection, the step geometry, the 60 degree slope limit and the 4 ft and 10 ft thresholds.

OSHA figures used in this guide
Item Requirement Source
Maximum intended load The employee plus all tools, equipment and materials carried 1910.21(b)
Loading Portable ladders are not loaded beyond the maximum intended load 1910.23(c)(3)
Intended use Ladders are used only for the purposes they were designed for 1910.23(b)(8)
Inspection Before initial use in each work shift, and more often as needed 1910.23(b)(9)
Step rise and depth Rise not more than 10 in, depth not less than 7 in 1910.23(e)(1)
Stair slope Not more than 60 degrees from horizontal 1910.23(e)(1)
Strength Supports at least four times the maximum intended load 1910.23(e)(1)
Height to base Work surface not more than four times the shortest base dimension without added support 1910.23(e)(1)
Movement Casters impede movement when occupied. Unit is not moved with a person on it 1910.23(e)(1)
Handrails Top step 4 ft or higher 1910.23(e)(1)
Guardrails and toeboards Platforms above 10 ft 1910.23(e)(3)
This is a selection aid, not a compliance program

1910.23 contains more than is summarized here. Fixed ladders, fall protection under 1910.28 and 1910.29, and training under 1910.30 carry their own requirements. Confirm your program against the standards and your own safety staff.

Section Ten

Choosing by application

Find the row that matches your situation.

Short answer: Start with the working height and what people carry. Then decide how often the ladder moves and what the floor is like.

General warehouse access
A steel rolling safety ladder with a top platform, handrails and spring-loaded casters. Check the listed capacity against the person plus the load.
Order picking, up and down all day
A stock picking ladder. Consider aluminum so it is easy to move, and a 50 degree walk-down if people carry cases.
People carry tools and materials up
More capacity, and a walk-down angle so they can hold a rail. Run the sum in section one first.
The ladder moves many times a day
Aluminum. Weight decides whether people move it or lean out sideways.
Access over a machine, tank or conveyor
A cantilever ladder. Expect a larger, heavier base.
People climb over a conveyor line
A crossover. Portable if the layout changes, fixed where the crossing is settled.
The task is 12 in to 18 in out of reach
A one-step platform parked where the task is.
Standing and working at height
A work platform, so both hands are free and the footing is a floor.
Food, pharmaceutical or washdown
Stainless steel. Confirm the grade against your cleaning chemicals.
Wet, oily or icy floors and docks
Grip strut or serrated grating treads.
Working above 10 ft
Confirm the quote includes the guardrails and toeboards the rule calls for at that height.
People climb on racking or pallets
The right equipment is missing, too far away or too hard to move. Fix the access, not just the rule.
Section Eleven

Common mistakes, and what to inspect

The first mistake is the one that matters most.

Short answer: Do not read the rating as body weight, do not compare quotes with different rail packages, and inspect every ladder before first use each shift.

Reading the rating as body weight

It is the person plus gear, tools and materials.

Buying a light duty type for plant work

Types II and III are commercial and household ratings.

Choosing the angle by footprint alone

A steep ladder saves floor space and makes the descent awkward. If people carry things, pay for the walk-down.

Comparing quotes across the 10 ft line

A cheaper quote may simply leave out guardrails and toeboards.

Buying steel where the ladder moves constantly

A heavy ladder is one people work around.

Skipping the one-step platform

Most improvised climbing happens over very short reaches.

Moving a ladder with someone on it

Prohibited by 1910.23(e), and a cause of injuries all by itself.

Inspection checklist

1910.23(b)(9) requires ladders to be inspected before initial use in each work shift, and more often as needed, for visible defects that could cause injury.

  • Steps and treads: worn surfaces, loose or bent steps.
  • Handrails and guardrails: secure at both ends. A rail that moves when pulled is a defect.
  • Welds and joints: especially where the stairs meet the platform and the base.
  • Casters: spring-loaded casters retract under load and the ladder settles on its feet. Manual locks engage firmly.
  • Feet and pads: worn or missing rubber tips.
  • Stability: push it. If it rocks, find out whether it is the ladder or the floor.
  • Rating label: readable. If nobody can read the rating, nobody is checking against it.
  • Defective ladders: tag them and take them out of service.
Make the shift inspection realistic

A per-shift inspection only happens if it takes seconds. A short laminated checklist tied to the ladder gets used more than a procedure in a binder.

Section Twelve

Frequently asked questions

What comes up most often on quote calls.

Does the load rating mean the user's weight?

No. It covers the person plus clothing, protective gear, tools and materials carried. OSHA defines maximum intended load in 1910.21(b) as the total load of the employee and all tools, equipment and materials being carried.

Which rating should I buy for industrial use?

For portable ladders, Type IA at 300 lb is a sensible floor and Type IAA at 375 lb is worth it where people carry tools or materials. For rolling ladders and platforms, use the load capacity on the listing and leave a margin above the person plus the load.

Why is Type III the lightest?

The ANSI duty types run backwards. Type III is light duty at 200 lb, Type II is 225 lb, Type I is 250 lb, Type IA is 300 lb and Type IAA is 375 lb.

What climbing angle should I choose?

OSHA limits mobile ladder stand stairs to 60 degrees. A standard rolling ladder is near that limit and has the shortest footprint. A 50 degree walk-down ladder lets people descend facing forward and carry items, and needs about 2 ft 5 in more stair run on a 10 ft climb.

At what height do I need handrails and guardrails?

Under OSHA 1910.23(e), mobile ladder stands and platforms with a top step height of 4 ft or more need handrails. Platforms above 10 ft need guardrails and toeboards on the exposed sides and ends.

Steel, aluminum or stainless?

Steel is the default for a ladder that stays in one area. Aluminum is for ladders moved many times a day. Stainless is for washdown and sanitary areas.

How do rolling ladder casters lock?

Spring-loaded casters carry the empty ladder, then retract under a person's weight so the ladder rests on rubber-tipped feet. Other ladders use manual locks or brakes that the user sets before climbing.

What is a cantilever ladder for?

It has a platform that extends past the base, so you can work over a machine, tank or conveyor that you cannot roll a ladder base up against.

Portable or fixed crossover?

Choose portable when the layout changes or you want to test a crossing point. Choose fixed when the obstacle is permanent and the crossing is used constantly.

How often do ladders have to be inspected?

OSHA 1910.23(b)(9) requires inspection before initial use in each work shift, and more often as needed, to find visible defects that could cause injury.

Can I move a rolling ladder with someone on it?

No. OSHA 1910.23(e) says a mobile ladder stand or platform is not moved while an employee is on it.

Section Thirteen

Quick-reference tables

Ratings and product families referenced in this guide.

Portable ladder duty types
Type Duty Rated load Where it belongs
Type IAA Special duty 375 lb Where tools and materials are carried
Type IA Extra heavy duty 300 lb Sensible floor for plant work
Type I Heavy duty 250 lb Only where the load is controlled
Type II Medium duty 225 lb Commercial
Type III Light duty 200 lb Household
Product families we list
Family Listing Best for
Rolling safety ladders Ballymore and Cotterman steel ladders General raised access
Stock picking ladders Stock picking ladders Constant up and down
Walk-down ladders 50 degree walk-down ladders Frequent climbing, carrying loads
Cantilever ladders Ballymore cantilever ladders Reaching over equipment
Stainless ladders Ballymore stainless ladders Washdown
Aluminum ladders Aluminum rolling ladders Frequent moves
Work platforms Single entry platforms, one-step platforms Standing work, short reaches
Crossovers Portable, fixed Conveyors and pipe runs
Before you order

Confirm the load capacity, overall height, base size and rail package on the listing for the exact model. Tell us the working height, what people carry up, how often the ladder moves and the floor condition, and we will specify it.

About the author. Tom McGovern has worked in the industrial material handling industry since 1981, bringing over 45 years of hands-on experience helping businesses select the right equipment for their applications. His expertise includes specifying and quoting rolling safety ladders, stock picking ladders, work platforms and crossovers.

Questions about this guide? Call 866-333-0728 to speak with an experienced material handling specialist.

Ready for a quote?

Send us these details and a material handling specialist will reply, typically within one business day.

  • Dimensions
    Size of the load and the space it goes in
  • Load
    Weight per item, shelf or level
  • Quantity
    How many units you need
  • Delivery ZIP code
    For freight pricing
  • Drawing
    A sketch, photo or spec sheet, if you have one
Get a Fast Quote Call 866-333-0728

Tell us the height and what goes up with them

Working height, what people carry, how often it moves and what the floor is like. Those four answers specify this category. Quotes are reviewed by material handling specialists, typically within one business day.

866-333-0728

Browse ladders & platforms at custommhs.com

No bots. No guesswork. Real experts.

Sources

OSHA 29 CFR 1910.21 and 1910.23 · ANSI ladder duty rating classifications · Ballymore and Cotterman information as published on CustomMHS product listings.

Disclaimer. This guide is educational content and reflects the opinion and general experience of CustomMHS. It is not a compliance assessment or legal advice. Ladder safety is governed by OSHA 1910.23 in full, with related requirements in 1910.28, 1910.29 and 1910.30. Confirm equipment ratings against the manufacturer's data and your program against the standards. Reviewed November 2026.