Section OneWhich plastic pallet type do you need?
The answer comes from one question: what is underneath the pallet when it is loaded?
Short answer: Use a nestable pallet for shipping and floor storage where empties come back, a stackable pallet when loaded pallets sit on top of each other, and a rackable pallet any time the load spans open rack beams.
Quick answers- Nestable: Lightest and lowest cost per trip out. Nests when empty. Floor and shipping use.
- Stackable: Bottom runners spread the load so loaded pallets stack. Needs full support under it.
- Rackable: Reinforced to span two beams with nothing in between. Heaviest and usually the most expensive.
Plastic pallets are sold by type because the bottom of the pallet is built differently on each one. A nine-leg nestable has no bottom deck at all. A stackable adds runners. A rackable adds a continuous runner base and, on many models, steel reinforcement. The top deck can look identical on all three.
A note on this guideThis guide is written from published manufacturer data and my own experience quoting this equipment. It is general guidance and my opinion, not engineering advice. Confirm the rating for your exact model and application before you order.
Section TwoHow each type is built
The underside tells you what the pallet is for.
Short answer: Legs mean nestable, runners mean stackable, and a reinforced three-runner or perimeter base means rackable.
Nestable
Open underside, commonly nine legs
Legs drop into the pallet below when empty. Typically 20 to 30 lb. Suppliers claim up to four times the space efficiency when shipping empties.
Stackable
Runners added under the legs
Often the same mold as a nestable with runners added. The runners spread the weight across the load below. It needs full support underneath.
Rackable
Continuous three-runner or perimeter base
Built for open-beam, push-back and edge racks. Commonly 35 to 55 lb. Steel reinforcement is common because steel is about 30 times stiffer than polypropylene or HDPE.
Plastic pallet types compared| Type | Typical weight | Nests empty | Stacks loaded | Open rack beams |
|---|
| Nestable | 20 to 30 lb | Yes | No | No |
| Stackable | Varies by runner design | No | Yes | Only on a wire mesh deck |
| Rackable | 35 to 55 lb | No | Yes | Yes |
Section ThreeLoad ratings by type
The same pallet carries three different ratings, and the type decides how far apart they are.
Short answer: Nestable pallets show the widest gap between static and dynamic ratings. Only a rackable pallet carries a racking rating you can use.
Every plastic pallet has a static rating (sitting on a flat floor), a dynamic rating (being moved by a forklift or pallet jack) and a racking rating (supported at two edges with nothing beneath). The racking number is normally the lowest and is often left off spec sheets for pallets that were never meant for a rack.
Published examples of the gap between ratings| Pallet | Static | Dynamic | Ratio |
|---|
| Nestable, example one | 10,500 lb | 1,500 lb | About 7 to 1 |
| Nestable, example two | 20,000 lb | 5,000 lb | 4 to 1 |
| Galvanized wire pallet, 40 x 48 in. | 4,000 lb | 2,500 lb | About 1.6 to 1 |
A stackable pallet rated 30,000 lb on the floor may still be unsuitable across beams. A floor rating tells you nothing about what the pallet does when the middle is unsupported. Our guide on pallets goes through the three ratings one at a time.
Ask for all three in writingWhen you request a quote, ask for the static, dynamic and racking rating of the exact model. If the racking rating is missing, treat the pallet as not rackable.
Section FourChoosing by application
Find the row that matches how the pallet is used.
Short answer: Decide by the most demanding thing the pallet will ever do. A pallet that goes in a rack even once needs to be rackable.
One-way or closed-loop shipping with empties returning
Nestable. The space saved on the empty leg is the whole reason this type exists.
Floor storage, loaded pallets not stacked
Nestable is usually enough. Check the dynamic rating against your load.
Loaded pallets stacked on each other
Stackable. The runners keep the legs from punching into the load below.
Selective rack with wire mesh decking
Stackable can work because the deck supports the runners. Confirm with the pallet maker and check the deck rating.
Open-beam, push-back or edge rack
Rackable only. Ask for the racking rating at your beam spacing.
Cold storage or freezer
Check the material. HDPE has a published service range of about -40 to 140°F. Polypropylene turns brittle below freezing.
Steam, autoclave or hot washdown
Polypropylene, with a published service range of about 50 to 230°F.
Browse the three types here: nestable plastic pallets, stackable plastic pallets and rackable plastic pallets.
Section FiveWorked example: what nesting saves on the return trip
The formula is simple and worth running before you choose.
Short answer: Return trips saved equals empties per trailer nested, divided by empties per trailer stacked, minus one.
Say a trailer returns a set number of empty stackable pallets, and the nestable version of the same footprint fits four times as many. The math is 4 divided by 1, minus 1, which is 3. One trailer brings back what used to take four, so three return trips are saved for every four you ran before.
Run the numbers with the stack heights your carrier allows and the nested height on the spec sheet for your model. The four to one figure is a supplier claim for best cases, so use your own count.
Where the saving disappearsIf loaded pallets must stack in your warehouse, or the pallet goes in a rack, a nestable is the wrong pallet no matter what it saves on freight.
Section SixCommon mistakes
Each one is cheap to avoid before the order.
Short answer: Most pallet failures come from using a floor pallet in a rack or reading the static rating as the working rating.
- Buying on the static rating. The static number is the largest and is often printed largest. It only applies on a flat floor.
- Putting a stackable pallet on open beams. Without wire decking or a pallet support, a stackable pallet spans the beams on runners that were not designed for it.
- Ignoring creep and temperature. Plastic deflects slowly under a sustained load. Rack ratings are typically set at about 70°F, and heat lowers them.
- Forgetting fire classification. Under NFPA 13, plastic pallets raise the commodity class of what is stored on them. Tell whoever handles your fire protection that you are changing from wood.
- Mixing types in one fleet. A nestable and a rackable pallet should not be interchangeable on your floor. Color-code them or keep them in separate areas.
Section SevenFrequently asked questions
The questions I hear most on quote calls.
What is the difference between nestable, stackable and rackable pallets?
A nestable pallet has legs that drop into the pallet below when empty. A stackable pallet adds bottom runners so loaded pallets can sit on each other. A rackable pallet has a reinforced base that can span open rack beams.
Can I put a nestable pallet in a pallet rack?
Not on open beams. A nestable pallet has no bottom structure to span the gap between the beams. Use a rackable pallet.
Can a stackable pallet go in a rack?
Only when it is fully supported, for example on wire mesh decking, and only if the pallet maker and the deck rating allow it. On open beams, use a rackable pallet.
Which plastic pallet type costs the least?
Nestable pallets are the lightest, typically 20 to 30 lb, and are usually the lowest cost. Rackable pallets, commonly 35 to 55 lb, are usually the most expensive.
How much do plastic pallets weigh?
Nestable pallets typically weigh 20 to 30 lb and rackable pallets commonly weigh 35 to 55 lb. Heavy-duty plastic pallets run up to 55 lb.
Are plastic pallets exempt from ISPM-15?
Yes. Plastic pallets are exempt from the ISPM-15 heat treatment rule that applies to wood packaging for export.