Section One
The three load ratings
Three numbers for three different situations. Usually only one of them limits you.
Quick answers
- A pallet has three ratings. Static is sitting on the floor, dynamic is being moved, and racking is spanning two rack beams. Racking is usually the lowest.
- Nestable, stackable and rackable describe the shape of the bottom, not a strength ladder. A stackable pallet is not a rack pallet.
- HDPE is the freezer material. Polypropylene is stiffer and takes more heat but gets brittle near freezing.
- Plastic pallets can change how a building must be sprinklered. Ask about fire classification before you order.
- Plastic pays back when the pallet comes back. On one-way shipments it usually does not.
What each rating means
| Rating |
Situation |
How it compares |
| Static |
The pallet is not moving and sits on a flat floor, fully supported |
The largest number, and usually the one printed largest |
| Dynamic |
The pallet is being moved by a fork truck or pallet jack |
Lower, because the load is carried on the forks and shifts as it moves |
| Racking |
The pallet spans two rack beams with nothing under the middle |
Usually the lowest, and the one most often left off a spec sheet |
How far apart the numbers are
On pallets in this category, one nestable plastic pallet is listed at 10,500 lb static and 1,500 lb dynamic. That is seven to one on the same pallet. Another in the family is 20,000 lb static and 5,000 lb dynamic, four to one. The galvanized wire pallet is 4,000 lb static and 2,500 lb dynamic, a much tighter ratio, which tells you something useful about steel.
The headline number is rarely the one you need
If a fork truck ever picks the pallet up, the static rating is not your limit. If the pallet goes into rack, neither static nor dynamic is your limit. Ask for all three in writing. If there is no racking figure, treat that as an answer.
The rack can also be the limit. Two 3,000 lb pallets on a beam pair rated at 5,000 lb per level is a rack problem, and no pallet fixes it. Check the rack capacity plaque first. Our pallet racking guide covers beam capacity.
The international test standard is ISO 8611, Pallets for materials handling. Part 1 covers test methods, Part 2 performance requirements and Part 3 maximum working loads. Ask which standard a rating was tested to.
Please read this part
This guide is educational and reflects the opinion and general experience of CustomMHS as an equipment distributor. It is not a fire protection, structural or regulatory assessment. Load ratings are the manufacturers' published figures. Confirm the current data sheet for your exact model before you order.
Section Two
Nestable, stackable, rackable
These words describe the bottom of the pallet. Reading them as weakest to strongest is how buyers get the wrong pallet.
Short answer: Nestable pallets nest when empty. Stackable pallets stack when loaded and need full support. Rackable pallets are the only ones made to span rack beams.
Empty storage and one-way shipping
Nestable
Legs drop into the pallet below, which saves floor space and return freight. Usually the lightest. The open-footed bottom has little beam strength, which is why the dynamic rating is a fraction of the static one. See nestable plastic pallets.
Loaded stacking
Stackable
Runners across the feet let loaded pallets stack on each other. They need to be fully supported, on a floor or a wire deck. See stackable plastic pallets.
Open rack beams
Rackable
Built to carry a load across two beams. Heavier and usually the most expensive. See rackable plastic pallets.
Stackable is not rackable
A stackable pallet that holds a very large load on the floor may be unsuitable across two beams, because the floor was doing the structural work. Do not carry a floor rating into the rack.
Worked example: what nesting saves
Those counts are an illustration. Use the nesting height on the listing and your trailer to get your own, then price the trailers at your lane rate. Nesting only pays if the empties come back. On a true one-way shipment, a light, low-cost pallet is the right product.
Section Three
What makes a pallet rackable
Not a label. Continuous runners, and often steel inside them.
Short answer: A rack pallet needs runners that act as beams. Plastic also sags slowly under a constant load, so steel reinforcement and wire decking matter for long-term rack storage.
On the floor, the whole base is supported. In a selective rack, only the two beams support it, and the runners have to span the gap. Separate feet cannot bridge an open span, which is why a nestable pallet is not a rack pallet no matter how large its static number is.
Why steel reinforcement matters
Stiffness is measured by modulus of elasticity. Steel is about 29,000,000 psi. Polypropylene and HDPE are in the range of 100,000 to 250,000 psi. For the same cross-section, steel resists bending more than 100 times better. That is why rackable plastic pallets often have steel rods in the runners, and why two pallets that look alike can be rated very differently.
Creep: the slow failure
Plastic under a constant load keeps deflecting slowly over time. A pallet that measured fine on day one can be visibly sagging a year later. ISO 8611 includes a long-term test for this. If your racked stock sits for months, ask about reinforcement and long-term rack ratings.
Rack ratings are set at room temperature
Heat makes plastic softer and speeds up creep. Cold makes it stiffer and more brittle. If your rack is in a freezer or on a hot dock, ask what temperature the rating was tested at.
Worked example: pallet depth and rack depth
A 48 in by 40 in pallet in a selective rack
| Item |
Dimension |
| Pallet depth, front to back |
48 in |
| Common rack frame depth for that pallet |
42 in |
| Overhang |
3 in at the front beam and 3 in at the back |
The runners have to land on both beams with that overhang. Confirm which pallet dimension runs front to back in your rack before you order. A wire deck across the beams supports the whole pallet base, which is often less expensive than upgrading every pallet.
Section Four
Material and temperature
HDPE and polypropylene are not interchangeable, and the difference shows up at the extremes.
Short answer: Use HDPE for freezers and cold rooms. Use polypropylene where stiffness and heat matter. Ask for UV stabilizer on anything stored outdoors.
The cold storage answer
HDPE
High density polyethylene keeps its toughness in the cold and is commonly published for service down to about -40°F. It also has broad resistance to acids, bases and water-based solutions.
The stiffness and heat answer
Polypropylene
Stiffer than HDPE and more tolerant of heat, which suits hot wash cycles. Its weak point is cold: it loses impact strength near and below freezing, around 32°F.
The freezer trap and the sunlight trap
A fork tine hit that a room-temperature polypropylene pallet shrugs off can crack a frozen one. If pallets live in a freezer, write HDPE on the purchase order. Plastic stored in a yard or under skylights also needs a UV-stabilized material. Ask for it by name.
Aluminum and wire
Hygiene and long life
Welded aluminum
The Vestil solid top welded aluminum pallets and skids are all-welded and aimed at washdown areas, food and beverage, and pharmaceutical work. Published capacities are 4,000 lb on the smaller footprints and 6,000 lb at 40 in by 48 in and 48 in by 48 in.
Drainage and visibility
Galvanized welded wire
The Vestil galvanized welded wire pallet has a 2 in by 4 in wire grid on a 12 gauge steel understructure, with four-way fork truck and pallet jack access. The 40 in by 48 in model is published at 4,000 lb static and 2,500 lb dynamic and weighs 47 lb. The 48 in by 48 in weighs 54 lb.
Section Five
How the pallet was made, and when to go custom
Two pallets of the same size and resin can behave very differently because of how they were formed.
Short answer: Injection molding suits standard sizes in volume. Structural foam makes thick, stiff, lighter parts. Thermoforming has low tooling cost, which makes custom sizes practical.
Three processes
| Process |
How it works |
What it means for you |
| Injection molded |
High pressure, tight tolerances, expensive tooling |
The mainstream process for standard footprints in volume |
| Structural foam |
Low pressure with a foaming agent, thick walls |
Good strength for the weight and good resistance to warping. The swirled surface does not matter on a pallet |
| Thermoformed |
A plastic sheet formed under heat and pressure. Twin-sheet bonds two sheets into a hollow structure |
Much lower tooling cost, which makes custom footprints practical at modest volumes |
See thermoformed plastic pallets and the top cap pallet system.
When custom is the right answer
Custom makes sense when your load does not fit a standard footprint, when the fork openings have to match automation, or when a slightly different size fits more product per trailer. One example from our listings is a 48 in by 48 in stackable pallet in black HMWPE at about 32 lb, built for a footwear manufacturer with four-way fork truck and two-way pallet jack entry. See custom built plastic pallets.
The question that decides it
How much of your trailer are you wasting because your product does not fit a 48 in by 40 in pallet? If it is more than a few percent and you ship constantly, a custom footprint can pay for its tooling out of freight. If you ship now and then, a standard pallet is the right call.
Section Six
Footprint and entry
The 48 by 40 is a convention, and four-way entry is not always four-way.
Short answer: Confirm the size, which dimension faces the forks, and whether a pallet jack can enter from all four sides or only two.
The North American standard grocery pallet is 48 in by 40 in. In wood it is commonly published as three notched stringers with seven top deck boards, about 30 to 48 lb empty. Hold a plastic quote against the wood pallet you use now, and ask for the same three ratings on both.
Notched stringers are partial four-way
A notched stringer pallet lets a fork truck enter from all four sides, but a pallet jack only from two, because the jack's wheels need a full opening. Many plastic pallets are four-way for fork trucks and two-way for jacks. The listing should say which. Check it against the equipment you run.
Get the dimensions the right way around
A 48 by 40 and a 40 by 48 can be the same pallet described from different sides. In rack and automation, 40 in deep and 48 in wide is a very different fit from the reverse. Confirm which dimension runs front to back.
Overhang costs more than it looks
Corrugated cases carry load in their vertical corners. A case that hangs over the pallet edge has corners with nothing under them and loses much of its stacking strength. The fix is usually a different footprint, not a stronger pallet.
Section Seven
The fire code question
Most pallet guides leave this out, and it can carry the largest cost.
Short answer: Under NFPA 13, plastic pallets can raise the commodity class of what is stored on them, and idle plastic pallets have their own storage limits. Ask before you order.
Switching from wood to plastic pallets can change how a building has to be sprinklered. Not the pallets. The building.
How the codes treat plastic pallets
| Point |
What it says |
Source |
| Commodity class |
Unreinforced polypropylene or HDPE pallets raise the commodity class by one. Reinforced plastic pallets raise it by two |
NFPA 13 |
| Listed pallets |
Plastic pallets tested and listed as equivalent to wood, to UL 2335 or FM 4996, are treated as wood |
NFPA 13 |
| Idle pallet storage |
Outside or in a detached building is preferred. Indoor storage has specific sprinkler protection criteria |
NFPA 13, FM Global Data Sheet 8-24 |
| High-piled storage |
Begins above 12 ft for ordinary commodities and above 6 ft for high-hazard commodities, which include idle pallets |
International Fire Code |
Reinforced and unreinforced here refer to the pallet's design and fire testing, not to whether you can see steel in it. A higher commodity class drives sprinkler density and design, and a warehouse designed for one class does not automatically cover the next.
What to do about it
Ask us whether the pallet has been fire tested and how it is classified, and get the answer in writing. Send it to your fire protection engineer or insurer, with where you plan to store empties and how high. In many buildings the answer is fine. In some it comes back with a cost, and it is better to see that while the order is still a draft. This guide is not a fire protection assessment. Your authority having jurisdiction and your insurer decide.
Section Eight
Export and ISPM-15
One place where plastic wins with no trade-off.
Short answer: Wood pallets for export must be treated and marked under ISPM-15. Plastic pallets are outside that standard.
ISPM-15 is the international standard for wood packaging, written to stop wood-boring pests from traveling in pallets and dunnage. It is widely adopted. If you export on wood, it applies.
Wood against plastic for export
|
Wood |
Plastic |
| Treatment |
Heat treatment to a core temperature of about 133°F (56°C in the standard) for at least 30 minutes, or approved fumigation |
None |
| Marking |
The IPPC mark with country code, facility number and treatment code |
None |
| Risk at the border |
A missing or unreadable mark can hold a shipment |
Not subject to ISPM-15 |
The saving is more than the treatment fee. It is the checking of marks and the risk of a held container. One qualification: the United States and Canada exempt wood packaging moving between the two countries when it is made of wood from either country. If all your export volume moves that way, this argument for plastic is weaker. Check your lanes.
Section Nine
Food, pharmaceutical and washdown
The hygiene case is real, and it is about absorbency.
Short answer: Wood absorbs water and whatever is in it. Plastic and aluminum do not, so they can be washed and checked.
The problem with wood in a food or pharmaceutical area is not that it is dirty. It is that it is absorbent. Wood takes up water, and that water can carry organisms such as Salmonella or Listeria. A wood pallet carries the history of everywhere it has been, and you cannot see it.
A pallet that does not absorb can be washed, sanitized and checked. That is the reason processors move to plastic and aluminum. Some food safety audit programs also mark a plant down for wood in a processing area, whether or not contamination is ever found.
- Nails and broken boards: set those pallets aside. Nails and splinters are foreign material hazards.
- Previous contents: reject pallets soiled with waste or chemicals. With an exchanged wood pallet you usually cannot know.
- Deck style: a solid deck is easier to wash and inspect than an open deck. If your sanitation program includes a swab, buy the solid deck.
For this work the choice is usually a solid deck plastic pallet or welded aluminum. Aluminum costs more, has no fasteners to shed, and lasts.
Section Ten
When plastic pays back
There is a real break-even, and plenty of operations sit on the wrong side of it.
Short answer: Cost per trip is the purchase price divided by the trips you actually get. Plastic wins in a closed loop and loses on one-way shipments.
Illustration only. Use your own prices and loss rates
| Case |
Math |
Cost per trip |
| Wood pallet at $15, lasts 10 trips |
$15 ÷ 10 |
$1.50 |
| Plastic pallet at $80, closed loop, 100 trips |
$80 ÷ 100 |
$0.80 |
| Same plastic pallet, 30% lost each trip |
1 ÷ 0.30 = about 3.3 trips. $80 ÷ 3.3 |
About $24 |
| Same plastic pallet, shipped one way |
$80 ÷ 1 |
$80 |
Plastic does not fail on price. It fails on getting the pallet back. Plant-to-plant moves and loops where you control both ends clear the bar easily. Shipments to customers who return nothing do not. Count the trips you really get, not the trips the pallet is capable of.
Section Eleven
Pallet stands and working height
A pallet on the floor puts the bottom layer at ankle height. Somebody has to reach it.
Short answer: A pallet stand raises the pallet to a fixed working height. If the right height changes as the pallet empties, use a self-leveling positioner.
Fixed position
Adjustable pallet stand
The MECO adjustable pallet stand is all-welded structural channel, 40 in by 40 in, with working heights of 24 in, 30-1/2 in and 34 in, rated at 4,000 lb. A locking mechanism keeps it from folding in use. It folds to 8-3/4 in for storage.
Mobile
Pallet stand on casters
The mobile pallet stand adds two swivel and two rigid 5 in casters. The working heights move up to 30-1/2 in, 37 in and 40-1/2 in, and capacity stays at 4,000 lb. If you bought a stand to lower a reach, note that the heights go up.
Worked example. Six stands folded at 8-3/4 in each stack to 6 × 8-3/4 in = 52-1/2 in, or 4 ft 4-1/2 in against a wall.
A stand gives fixed heights. If the right working height changes as the pallet is built or picked down, a self-leveling positioner or a lift table does that and a stand does not. See our lift tables guide.
Section Twelve
Choosing by application
Find the row that matches your situation.
Short answer: Decide where the pallet will sit, how it moves, whether it comes back, and the temperature.
Floor storage and stacking loaded pallets
A stackable pallet. Compare the static and dynamic ratings to your load.
Open-beam pallet rack
A rackable pallet with a written racking rating, or add wire decking.
Empties come back by truck
A nestable pallet. Work out the return freight saved.
One-way shipping
A light, low-cost pallet. Do not pay for a benefit you will not collect.
Freezer or cold room
HDPE, written on the purchase order.
Hot wash cycles
Polypropylene, or aluminum.
Outdoor storage
A UV-stabilized material.
Food, beverage or pharmaceutical
A solid deck plastic pallet or welded aluminum.
Wet parts, drainage or visibility
A galvanized welded wire pallet.
Export
Plastic, to stay outside ISPM-15.
Odd load size or automation
A thermoformed or custom built pallet.
Hand picking from a pallet
A pallet stand, or a self-leveling positioner.
Any switch from wood to plastic in a sprinklered building
Ask about fire classification first.
Section Thirteen
Common and costly mistakes
Every one of these has been paid for by somebody.
Short answer: Do not use the static rating as the capacity, do not rack a stackable pallet, and ask about fire classification.
Quoting the static rating as the capacity
If the pallet is lifted, it is a dynamic question. If it is racked, it is a racking question.
Putting a stackable pallet on rack beams
It needs full support.
Assuming four-way entry includes pallet jacks
Confirm entry for the equipment you run.
Buying polypropylene for a freezer
It gets brittle near freezing. Specify HDPE.
Buying unstabilized plastic for outdoor storage
Ask for UV stabilizer.
Not asking about fire classification
Plastic pallets can raise the commodity class by one or two.
Buying nestable pallets for one-way shipping
Nesting only pays when empties return.
Building the business case on 100 trips
Use the trips you really get.
Getting 48 by 40 backwards
Confirm which dimension runs front to back in the rack.
Section Fourteen
Frequently asked questions
What comes up most often on quote calls.
What is the difference between static, dynamic and racking load?
Static is the load a pallet holds sitting still on a flat floor. Dynamic is the load it holds while a fork truck or pallet jack moves it. Racking is the load it holds across two rack beams with nothing under the middle, and it is usually the lowest of the three.
Can I put a stackable pallet in a pallet rack?
Not on open beams. Stackable pallets need full support, so they belong on the floor or on a wire deck. Use a rackable pallet with a published racking rating for open-beam rack.
What makes a pallet rackable?
Continuous runners that act as beams between the two rack beams, often with steel reinforcement inside. Separate feet cannot span an open gap.
HDPE or polypropylene?
HDPE keeps its toughness in the cold and is the choice for freezers. Polypropylene is stiffer and handles more heat but loses impact strength near and below freezing.
Do plastic pallets affect my sprinkler system?
They can. Under NFPA 13, unreinforced polypropylene or HDPE pallets raise the commodity class by one and reinforced plastic pallets by two, unless the pallet is listed as equivalent to wood. Ask for the fire classification in writing and give it to your fire protection engineer or insurer.
Are plastic pallets exempt from ISPM-15?
Yes. ISPM-15 covers wood packaging. Plastic pallets need no heat treatment or IPPC mark.
Is a four-way pallet four-way for a pallet jack?
Not always. Many pallets are four-way for fork trucks and two-way for pallet jacks. Check the listing against the equipment you run.
When does a plastic pallet pay for itself?
When it comes back. Divide the price by the trips you actually get. In a closed loop a plastic pallet costs less per trip than wood. On a one-way shipment it costs its full price on the first trip.
Are nestable pallets worth it?
If empties are trucked back, yes, because nested pallets take far less trailer space. If the pallet never returns, nesting saves you nothing.
What is a pallet stand for?
It raises a pallet off the floor to a working height so the bottom layers can be reached without bending. The MECO adjustable stand offers 24 in, 30-1/2 in and 34 in heights and is rated at 4,000 lb.
When should I order a custom pallet?
When the load does not fit a standard footprint, when fork openings must match automation, or when a different size fits more product per trailer and you ship often enough to recover the tooling.
Section Fifteen
Quick-reference tables
Published figures referenced in this guide.
Listed products
| Product |
Published on the listing |
| Nestable plastic pallets |
Examples: 10,500 lb static and 1,500 lb dynamic; 20,000 lb static and 5,000 lb dynamic |
| Stackable plastic pallets |
See listing |
| Rackable plastic pallets |
See listing |
| Vestil welded aluminum pallets |
4,000 lb on smaller sizes, 6,000 lb at 40 in by 48 in and 48 in by 48 in |
| Vestil galvanized wire pallet |
40 in by 48 in: 4,000 lb static, 2,500 lb dynamic, 47 lb |
| MECO adjustable pallet stand |
40 in by 40 in, heights 24 in, 30-1/2 in and 34 in, 4,000 lb, folds to 8-3/4 in |
| Custom built plastic pallets, thermoformed pallets |
Made to order |
Standards and codes
| Topic |
Reference |
| Pallet load testing |
ISO 8611, Parts 1 to 3 |
| Sprinkler protection and commodity class |
NFPA 13 |
| Idle pallet storage |
NFPA 13 and FM Global Data Sheet 8-24 |
| High-piled storage |
International Fire Code |
| Listed plastic pallets |
UL 2335, FM 4996 |
| Wood packaging for export |
ISPM-15 |
Before you order
Ask for static, dynamic and racking ratings in writing, the material, the fire classification, and whether a pallet jack can enter from all four sides. Tell us the load, how it moves, where it is stored and whether the pallet comes back.
About the author. Tom McGovern has worked in the industrial material handling industry since 1981, bringing over 45 years of hands-on experience helping businesses select the right equipment for their applications. His expertise includes specifying and quoting nestable, stackable and rackable plastic pallets, aluminum pallets, wire pallets and pallet stands.
Questions about this guide? Call 866-333-0728 to speak with an experienced material handling specialist.