Industrial Equipment Experts Since 1980 | Mon–Fri, 7 AM–6 PM ET
No bots. Real experts. 866-333-0728
Get a Fast Quote
Get a Fast Quote

CustomMHS Buyer's Guide

Stack and Nest Totes vs. Straight Wall Containers: How to Choose

One saves space when it is empty. The other saves space when it is full. Here is how to tell which problem you have.

Written and reviewed by: Tom McGovern, owner of CustomMHSPublished: November 2026Covers: LEWISBins · Monoflo · Quantum · Akro-Mils · Buckhorn · OrbisQuestions: 866-333-0728
Section One

Stack and nest or straight wall?

Ask where your space problem is: empty containers or full ones.

Short answer: Choose stack and nest totes when empties pile up or travel back. Choose straight wall containers when you need the most interior volume and the best pallet fit for full loads.

Quick answers
  • Stack and nest: Tapered walls. Stacks when loaded, nests when empty after a 180 degree turn.
  • Straight wall: Vertical walls. Best interior volume, stacks loaded, does not nest.
  • The formula: Positions saved = E x (1 - 1 / R), where E is the number of empties and R is the nest ratio.

Both styles stack when loaded. The difference is the wall. A tapered wall lets one tote drop inside another. A vertical wall gives up nesting and gets the full footprint all the way down.

A note on this guide

This guide is written from published manufacturer data and my own experience quoting this equipment. It is general guidance and my opinion, not engineering advice. Confirm the rating for your exact model and application before you order.

Section Two

How each style works

The wall angle is the whole story.

Short answer: Stack and nest totes turn 180 degrees to switch between stacking and nesting. Straight wall containers only stack.

Stack and nest

Tapered walls

Set one way, the tote sits on the rim of the one below. Turned 180 degrees, it drops inside. Empty density is high. The taper costs some interior volume at the bottom.

Straight wall

Vertical walls

The inside is nearly as large at the bottom as at the top, so parts, cartons and dividers fit squarely. Sized to tile a pallet. Empties take the same space as full ones.

Container styles at a glance
StyleLoaded stackingEmpty densityInterior volumeBest for
Stack and nestYes, rotated 180 degreesHighGoodClosed loops with a return leg
Straight wallYesLowBestReturnable programs, pallet cube
Nest onlyNoBestModerateMostly-empty fleets, conveyors
Attached lidYesHigh, lids openGoodTransit, security, chain of custody
Divider boxYesLowGoodKitting, multi-part assembly
Section Three

Published specifications

One example of each, from the listings.

Short answer: The stack and nest example nests 4 to 1. The straight wall example is built to tile a 48 x 45 in. pallet.

Two published examples
LEWISBins Polylewton SN3022-6 (stack and nest)Monoflo NSO1215-05 (straight wall)
Outside size29.6 x 22.4 in. at top, 6.1 in. high12 x 15 x 5 in.
Inside size27.6 x 21.4 in. at top, 26.1 x 20.5 in. at bottom9.4 x 13 in., 4.4 in. clearance
Volume2.1 cu ft0.3 cu ft
Load70 lb per toteSee data sheet
Stacking300 lb bottom container supportSee data sheet
Nest ratio4.0 to 1Does not nest
Tare4.8 lb1.7 lb
Pallet fitSee data sheet48 x 45 in. AIAG pallet compatible
Temperature0 to 120°FSee data sheet

Look at the inside dimensions on the stack and nest tote. The bottom is 1-1/2 in. shorter and about 1 in. narrower than the top. That is the taper, and it is the volume you trade for nesting.

Section Four

Worked example: what nesting gives back

Run the formula with your own empty count.

Short answer: At a 4 to 1 nest ratio, 400 empty totes need 100 positions instead of 400.

Positions saved = E x (1 - 1 / R). With 400 empties and the 4.0 to 1 ratio published for the SN3022-6:

400 x (1 - 1 / 4) = 400 x 0.75 = 300 positions recovered. The 400 empties take the space of 100.

At a 2.5 to 1 ratio the same 400 empties need 160 positions. The nest ratio is on the spec sheet, and it varies by model, so check it.

And the stacking limit

The same tote is rated 70 lb per tote with 300 lb of bottom container support. 300 / 70 is 4.3, so about four loaded totes can sit on the bottom one. The load rating and the stacking rating are two different numbers. Read both.

Section Five

Choosing by situation

Find the row that matches your operation.

Short answer: Empties are the deciding factor. If they are a problem, nest. If they are not, go straight wall.

Totes go out full and come back empty
Stack and nest.
Seasonal volume, many totes idle part of the year
Stack and nest, or nest only.
Returnable program on 48 x 45 in. pallets
Straight wall, sized to the pallet footprint.
Parts or cartons with square corners
Straight wall. The taper wastes the corners.
Kitting several part numbers per container
Divider box. See our containers guide.
Shipping with security or dust protection
Attached lid container. The Buckhorn AR24201202 is rated 80 lb and nests with the lids open.
Food handling
Check color and material. On the SN3022-6, blue and gray are FDA approved.
Static-sensitive parts
ESD containers. See our guide on ESD containers.
Section Six

Common mistakes

Check these before you order a fleet.

Short answer: The usual errors are ignoring the taper, stacking past the bottom support rating, and mixing styles that do not interstack.

  • Sizing to the top dimensions. Check the inside bottom size against your part, not the outside top size.
  • Stacking too high. The bottom tote carries everything above it. 300 lb of support is about four 70 lb totes.
  • Assuming every tote nests the same. A 2.5 to 1 tote needs 60 percent more room for empties than a 4 to 1 tote.
  • Mixing brands and series. Totes from different lines rarely stack or nest together. Standardize.
  • Paying for nesting you do not use. If empties never leave the cell, nesting buys nothing and the taper costs volume.
Section Seven

Frequently asked questions

The questions I hear most on quote calls.

What is the difference between a stack and nest tote and a straight wall container?

A stack and nest tote has tapered walls, so it stacks when loaded and nests inside another when empty. A straight wall container has vertical walls, so it holds more and stacks, but does not nest.

How do stack and nest totes work?

Set one way, a tote stacks on the one below. Turned 180 degrees, it nests inside it.

How much space does nesting save?

Positions saved equals the number of empties multiplied by one minus one over the nest ratio. At 4 to 1, 400 empties take 100 positions, saving 300.

Which holds more, stack and nest or straight wall?

Straight wall. Vertical walls give the best interior volume for a given footprint.

How high can I stack loaded totes?

Divide the bottom container support rating by the load per tote. The LEWISBins SN3022-6 is rated 300 lb of support and 70 lb per tote, so about four loaded totes on the bottom one.

Are straight wall containers sized for pallets?

Many are. The Monoflo NSO1215-05 is built to be compatible with the 48 x 45 in. AIAG pallet footprint.

About the author. Tom McGovern is the owner of CustomMHS, an industrial material handling distributor serving the US, Canada and Mexico. He has worked in material handling since 1981 and has quoted and specified the stack and nest totes, straight wall containers, divider boxes and attached lid containers sold at CustomMHS. Questions about this guide: 866-333-0728.

Ready for a quote?

Send us these details and a material handling specialist will reply, typically within one business day.

  • Dimensions
    Size of the load and the space it goes in
  • Load
    Weight per item, shelf or level
  • Quantity
    How many units you need
  • Delivery ZIP code
    For freight pricing
  • Drawing
    A sketch, photo or spec sheet, if you have one
Get a Fast Quote Call 866-333-0728

Not sure which tote style fits your loop?

Tell us the part, the load per tote and how many empties sit idle, and we will recommend a style and size. Quote requests are answered within 24 hours by a real person.

866-333-0728

Browse containers, totes and trays at custommhs.com

Get a fast quote

No bots. No guesswork. Real experts.

Specification sources

CustomMHS containers, totes and trays guide and product listings · LEWISBins, Monoflo, Buckhorn and Quantum published specifications.

Published figures are current as of November 2026 and are subject to change by the manufacturer. This guide is written from published manufacturer data and my own experience quoting this equipment. It is general guidance and my opinion, not engineering advice. Confirm the rating for your exact model and application before you order.