Butcher Block, Steel, Laminate or ESD: Choosing a Workbench Top
The top is the part of the bench that touches the work. Choose it by what lands on it: impact, chemicals, heat, liquid or static.
Written and reviewed by: Tom McGovern, owner of CustomMHSPublished: November 2026Covers: Little Giant · Rousseau · Jamco · Eagle · MetroQuestions: 866-333-0728
Section One
Which workbench top do you need?
Ask what the top has to survive.
Short answer: Choose maple butcher block for impact and heavy mechanical work, stainless steel for washdown and cleanrooms, plastic laminate for light assembly, and ESD laminate for electronics.
Quick answers
Maple butcher block: Absorbs impact. 1-3/4 in. thick. Low chemical resistance, and it absorbs liquids.
Stainless steel: High heat resistance, non-absorbent. For cleanrooms, washdown and food.
Plastic laminate: Economical and easy to clean. Low heat resistance, and vulnerable at the edges.
ESD laminate: Laminate that drains static to ground. For electronics production.
Most benches are offered with a choice of tops on the same frame. The frame sets the capacity. The top sets what the bench is good for.
A note on this guide
This guide is written from published manufacturer data and my own experience quoting this equipment. It is general guidance and my opinion, not engineering advice. Confirm the rating for your exact model and application before you order.
Section Two
The eight top materials compared
Resistance to chemicals, heat and moisture, side by side.
Short answer: No top is best at everything. Each one gives up something to gain something else.
Workbench top materials
Material
Chemical resistance
Heat
Moisture
Suits
Maple butcher block
Low
Moderate
Absorbs
Heavy industrial work, 1-3/4 in. thick
Stainless steel
Moderate to corrosives, high to carbon-based
High
Non-absorbent
Cleanrooms, washdown, food
Plastic laminate
Low to moderate
Low
Edge-sensitive
Light to moderate duty
ESD laminate
Moderate
Moderate
Resists humidity
Electronics production
Hardboard over steel
Low
Low
Absorbs
Sacrificial, replaceable surface
Phenolic resin
Moderate
Moderate
Moisture resistant
Medical, clinical, bio-science
Epoxy resin
High
High
Non-porous
Chemical labs, heavy duty industrial
HDPE polymer
Moderate
Poor
Non-absorbent
Food and beverage, wet areas
Section Three
Butcher block and steel
The two shop-floor standards.
Short answer: Butcher block forgives impact and dropped tools. Steel-based tops handle heat, oil and abuse that would ruin wood.
Maple butcher block
A 1-3/4 in. laminated maple top is the traditional heavy industrial surface. It absorbs impact, so it is kind to tools and parts. Its weaknesses are liquids and chemicals: it absorbs spills and has low chemical resistance. The Little Giant WSJ2-Series pairs a welded steel bench with a maple top at 3,000 lb.
Stainless steel
Non-absorbent, high heat resistance, and cleanable. It is the top for cleanrooms, washdown and food. The Little Giant WSS2-Series stainless top bench is rated 4,000 to 5,000 lb. See stainless steel benches.
Hardboard over steel
A steel top with a replaceable hardboard surface. It is economical, and when the surface is chewed up you replace the hardboard instead of the bench. It has low chemical and heat resistance and absorbs liquids, so treat it as sacrificial. The Little Giant WSH2-Series uses a hardboard top at 3,000 to 5,000 lb.
Hammering, pressing, drilling
For striking and pressing work, the frame matters as much as the top. Buy up the capacity ladder for stiffness. Ratings are for evenly distributed loads, not point loads.
Section Four
Laminate and ESD laminate
They look alike. They are not interchangeable.
Short answer: Plastic laminate is for general light assembly. ESD laminate is for static-sensitive electronics and only works when it is grounded.
Plastic laminate
Smooth, easy to clean and economical. It suits light to moderate duty: assembly, packing, inspection. It has low heat resistance, and the edges are the weak point for moisture.
ESD laminate
A laminate that lets static charge drain away through a ground connection. Electronic components can be damaged at about 30 volts. A person does not feel a static shock until about 3,000 volts. That gap is why damage happens without anyone noticing.
The top needs a verified path to ground, and the operator needs a wrist strap or ESD footwear. An ungrounded ESD top is an expensive laminate top. See what an ESD container is.
Section Five
Resin and polymer tops
For labs and wet processes.
Short answer: Epoxy resin is the chemical lab top. Phenolic resin is the lighter-duty lab top. HDPE is for food and wet areas.
Strong acids, solvents, open flame
Epoxy resin. High chemical and heat resistance, non-porous.
Clinical, medical and bio-science work
Phenolic resin. Moderate chemical and heat resistance, moisture resistant.
Food and beverage, constantly wet
HDPE polymer. Non-absorbent, but poor heat resistance.
Washdown with sanitizers
Stainless steel.
If a lab top is what you need, tell us the chemicals by name. Resistance varies by chemical, and the top should be matched to the actual list.
Section Six
Choosing by work, and common mistakes
Find your row, then check the list.
Short answer: Match the top to the worst thing that happens on it, not the usual thing.
Mechanical assembly, maintenance, vise work
Maple butcher block.
Oily parts, hot parts, rough use
Hardboard over steel, or stainless.
Packing, kitting, inspection
Plastic laminate.
Circuit boards and electronic assembly
ESD laminate, grounded.
Cleanroom or food
Stainless steel.
Chemical lab
Epoxy resin.
Oil and solvents on butcher block. It absorbs them and stains.
Soldering or hot parts on plastic laminate. Low heat resistance. Use a different top or a heat pad.
ESD top with no ground. No ground path, no protection.
Laminate where edges get wet. Seal or protect laminate edges in wet areas, or choose another top.
It depends on the work. Maple butcher block suits heavy mechanical work, stainless steel suits washdown and cleanrooms, plastic laminate suits light assembly, and ESD laminate suits electronics.
How thick is a butcher block workbench top?
The maple butcher block tops in our guide are 1-3/4 in. thick.
Is butcher block good for a workbench?
Yes for impact and heavy mechanical work. It absorbs liquids and has low chemical resistance, so it is a poor choice around oil, solvents and wet processes.
What is an ESD workbench top?
A laminate top that lets static charge drain to ground. Under ANSI/ESD S20.20 the worksurface point-to-point resistance is 0 to 1.0 x 10 to the 9th ohms. It must be grounded to work.
What is the difference between laminate and ESD laminate?
Plastic laminate is a general light-duty surface. ESD laminate is static dissipative and is used with a ground connection for electronics production.
Which workbench top resists chemicals best?
Epoxy resin, which has high resistance to both corrosive and carbon-based chemicals, high heat resistance and a non-porous surface.
About the author. Tom McGovern is the owner of CustomMHS, an industrial material handling distributor serving the US, Canada and Mexico. He has worked in material handling since 1981 and has quoted and specified the Little Giant, Rousseau and Jamco workbenches and stainless steel lab and cleanroom benches sold at CustomMHS. Questions about this guide: 866-333-0728.
Ready for a quote?
Send us these details and a material handling specialist will reply, typically within one business day.
✓Dimensions Size of the load and the space it goes in
✓Load Weight per item, shelf or level
✓Quantity How many units you need
✓Delivery ZIP code For freight pricing
✓Drawing A sketch, photo or spec sheet, if you have one
Tell us what the bench is used for and what gets spilled, dropped or soldered on it, and we will recommend a top. Quote requests are answered within 24 hours by a real person.
CustomMHS workbenches and workstations guide and product listings · ANSI/ESD S20.20.
Published figures are current as of November 2026 and are subject to change by the manufacturer. This guide is written from published manufacturer data and my own experience quoting this equipment. It is general guidance and my opinion, not engineering advice. Confirm the rating for your exact model and application before you order.
Business Deliveries
Standard Business Delivery (With Loading Dock) Delivery to a commercial address with a loading dock.
Business Delivery (No Dock, Forklift Available) Delivery to a commercial address with no dock, but a forklift is available on-site.
Business Delivery (No Dock, Liftgate Required) No dock or forklift on-site. Liftgate service is needed. Liftgate lowers items to ground level.
Business Delivery (No Dock, Manual Unloading) Delivery to a commercial location without a loading dock or equipment.
Limited Access Business (With Loading Dock) Delivery to a restricted-access site (e.g., government, schools, military, farm) with a dock.
Limited Access Business (No Dock, Forklift Available) Delivery to a restricted-access site (e.g., government, schools, military, farm) with no dock but a forklift is available on-site.
Residential Deliveries
Home Delivery is available with a $300 minimum product order. Orders below $300 will include an adjustment to bring the product total to the $300 minimum.