Industrial Equipment Experts Since 1980 | Mon–Fri, 7 AM–6 PM ET
No bots. Real experts. 866-333-0728
Get a Fast Quote
Get a Fast Quote

CustomMHS Buyer's Guide

Workbenches & Workstations

Almost every workbench is bought at about 34 inches high because that is what benches are. The right height depends on the task and the person, and getting it wrong costs output every hour of every shift. Here is how to specify height, surface, capacity and lighting from the task.

Covers: Rousseau · Pro-Line · Little Giant · Jamco · Strong Hold · Metro Questions: 866-333-0728 Written and reviewed by: Tom McGovern · November 2026
Section One

Height is a task decision

The most important number on a bench quote, and the one most often left at the default.

Quick answers
  • Set bench height from the worker's elbow height and the task: about 2 in above the elbow for precision work, 2 in to 4 in below for light work, and 8 in to 16 in below for heavy work.
  • Measure to the work, not the bench top. A 4 in fixture on a 34 in bench is a 38 in working height.
  • Bench capacities assume an evenly spread load. A machine on four feet needs a machine stand.
  • A static-safe top does not make a static-safe workstation. The person, chair, bins and floor are part of it.
  • Exacting inspection needs about ten times the light of simple assembly. Put a task light on the bench.

Most benches are bought at about 34 in high because that is what benches are. There is no single right height. There is the right height for a task done by a person.

Work height from elbow height, standing
Kind of work Work height Why
Precision work, such as electronics assembly About 2 in above elbow height, with elbow support You need to see it, and your forearms need support
Light work, such as assembly About 2 in to 4 in below elbow height Hands work freely without raising the shoulders
Heavy work with downward force About 8 in to 16 in below elbow height You need your body weight over the job

Those are the guidelines published by the Canadian Centre for Occupational Health and Safety. To find elbow height, stand straight with shoulders relaxed and elbows bent at 90 degrees, and measure from the floor to the elbow.

Worked example

A worker with a 42 in standing elbow height
Task Math Work height
Precision 42 in + 2 in 44 in
Light assembly 42 in − 2 in to 4 in 38 in to 40 in
Heavy work 42 in − 8 in to 16 in 26 in to 34 in
Light assembly in a 4 in tall fixture 38 in to 40 in − 4 in Bench top at 34 in to 36 in
Measure to the work

If the job sits in a fixture, jig or tote, the hands work at the top of that. Subtract it before you order.

A fixed height that suits a 5 ft 2 in worker does not suit a 6 ft 2 in one. On a shared or multi-shift station, that is the case for an adjustable height bench.

Please read this part

This guide is educational and reflects the opinion and general experience of CustomMHS as an equipment distributor. It is not an ergonomic assessment or an ESD program audit. Capacities and sizes are the manufacturers' published figures. Confirm the current data sheet for your exact model before you order.

Section Two

What a bench capacity covers

The capacity is real. It is rarely the number that decides the purchase.

Short answer: Bench ratings are for evenly spread loads. Use them as a guide to stiffness, and buy heavier if the work involves striking, pressing or vibration.

Listed fixed height bench capacities
Series Capacity
Jamco WD-Series 16,000 lb
Little Giant WX-Series, extra heavy duty 15,000 lb
Little Giant WW-Series, heavy duty 10,000 lb
Strong Hold adjustable shop table 10,000 lb
Little Giant WSS2-Series, stainless top 4,000 to 5,000 lb
Little Giant WST2, WSL2, WSH2 and WST1 Series 3,000 to 5,000 lb
Little Giant WSJ2-Series, maple top 3,000 lb
Jamco UA-Series 3,000 lb

See fixed height workbenches.

Evenly spread loads

A 5,000 lb bench is not a bench you can set a 5,000 lb machine on, because that load arrives through four small feet. For a concentrated load, tell us, or use a machine stand.

Few benches fail because someone exceeded the rating. They become hard to work at because the top flexes or the frame rings when struck. A top that moves under hand pressure makes precise work harder. If your work involves hammering, pressing or drilling, buy further up the list than the static load suggests. Welded construction has no fasteners to work loose.

Back and end stops keep parts from sliding off the surface. On a bench where small parts are handled, they are a low-cost improvement.

Section Three

Worksurface materials

Seven common surfaces. Each is the wrong answer somewhere.

Short answer: Maple for heavy bench work, stainless for washdown, epoxy for chemicals, static-dissipative laminate for electronics, and a replaceable hardboard top for rough work.

Worksurface characteristics
Material Chemicals Heat Moisture Suits
Epoxy resin High resistance High Non-porous Chemical and lab work
Stainless steel Good, depending on the chemical High Does not absorb Cleanrooms and washdown
Phenolic resin Moderate Moderate Resists moisture Medical and clinical work
Maple butcher block Low Moderate Absorbs Heavy industrial bench work
Static-dissipative (ESD) laminate Moderate Moderate Resists humidity Electronics
Plastic laminate Low to moderate Low Edges are sensitive Light to moderate duty
HDPE polymer Moderate Poor Does not absorb Food, beverage and wet areas

Maple butcher block

The industrial default. It absorbs impact, does not dent a workpiece, and can be sanded flat years later. It also absorbs oil and solvent, so it is wrong where chemicals or food are involved.

Hardboard over steel

A deliberately sacrificial top. You cut on it and spill on it, and when it is worn you replace the hardboard, not the bench.

Stainless

For washdown, check the frame as well as the top. See stainless steel benches, Metro stainless perforated top tables and our cleanroom and stainless guide.

Ask about your actual chemicals

"Chemical resistant" can mean different things for acids and for solvents. Give us the list of what will touch the surface.

Section Four

ESD workstations

A failure you cannot see, at voltages you cannot feel.

Short answer: ANSI/ESD S20.20 treats the worksurface, the person, the seating, the containers and the floor as one controlled area. A static-dissipative top is only the start.

Some electronic parts can be damaged by a static discharge of 100 volts or less. A person generally does not feel a discharge below about 3,000 volts. So damage at a bench happens without anyone noticing, and some of it shows up later as a field failure.

Parts of an ESD protected area
Element What ANSI/ESD S20.20 looks for
Worksurface A dissipative surface with a path to ground, with resistance below 1 × 109 ohms
People A wrist strap, or ESD footwear on an ESD floor, tested
Seating ESD chairs or stools
Containers and tools ESD-safe bins, totes and packaging. Ordinary plastics are kept away from sensitive parts
Verification Checks on a schedule, with records
An ESD bench is not an ESD workstation

A dissipative top with an ungrounded worker on a vinyl chair, picking parts from an ordinary plastic bin, is not protecting anything. Specify the station as a set.

See the Rousseau electronics workstation. Our containers and totes guide covers ESD containers and our chairs and stools guide covers ESD seating. Your own ESD program and the full standard govern.

Section Five

Fixed, adjustable or mobile

Three product types for three different problems.

Short answer: Fixed for settled, heavy work. Adjustable for shared stations. Mobile when the bench goes to the job.

Settled, heavy work

Fixed height

Nothing to adjust and nothing to fail, with the highest capacities. Right when one task is done at a known height. See fixed height workbenches and the Pro-Line HD modular workbench.

Shared or varied work

Adjustable height

Hand crank or electric. See the Rousseau Base Line, the Rousseau hand crank bench, the Pro-Line EL electric bench and adjustable technical benches.

Work that moves

Mobile

For maintenance and changeover work done at the machine. Casters raise the working height and reduce rigidity. See mobile workbenches.

Adjustment that takes two people gets done once

If changing the height needs tools, two people or a cleared bench, it will be set at installation and left. If the height has to change by worker or by job, buy electric.

Locking casters on a mobile bench

A bench that moves while someone is pressing, drilling or striking is a hazard. Use locking casters. Our carts guide covers caster selection.

Section Six

The base underneath

Mostly a question of where the legs and feet go.

Short answer: Four legs for rigidity, cantilever legs for seated work, an open base for bins and a stool, and a cabinet base for tools within reach.

Base types
Base What it gives What it costs
Four leg The most rigid, and the base under the highest capacities A front leg is where a seated worker's knee wants to be
Cantilever No front legs. Open for seated work, wheelchairs and carts Some capacity and rigidity. See the Pro-Line cantilever bench
Open base Clear underneath for bins or a stool No built-in storage
Cabinet Storage and stiffness in one footprint Nothing fits under it, so it is poor for seated work

Frames with uprights let you hang shelves, lights, tool rails and monitor arms on the bench. See the Rousseau three-sided bench, the Rousseau bench with monitor mount, Rousseau above-surface upgrades and Pro-Line accessories. If the station will be tuned over its first year, buy the frame that accepts accessories.

Bench tops are sold by top size. Ask for the base dimensions when you lay out a row.

Section Seven

Storage at the point of work

The return on a workstation is usually how far the worker has to reach.

Short answer: Put the most-used items within forearm reach. Use drawers for many small parts.

Rousseau modular drawer workstations as listed
Duty Capacity per drawer Suits
Heavy duty 400 lb Demanding assembly and larger tooling
Standard duty 100 lb Lighter assembly, electronics and bench work

Listed configurations run from 60 in wide by 30 in deep by 34 in high at bench height, through 72 in by 30 in, up to 90 in wide by 27 in deep by 60 in high. See Rousseau workbenches with modular drawers, the compact cabinet bench and the suspended cabinet bench.

A drawer shows all of its contents at once. A bin on a shelf under a bench has to be lifted out to be searched. Our cabinets and modular drawer guide covers drawers in detail.

  • Every cycle: within forearm reach, at or just below elbow height.
  • A few times a shift: lower or further out.
  • Weekly: not at the bench.

Worked example. A 30 in deep bench with a drawer pulled out about 24 in takes about 54 in, or 4 ft 6 in, from the back of the bench to the drawer front. Check that against the aisle where benches face each other.

Section Eight

Lighting the work

The lowest-cost quality improvement at a workstation.

Short answer: Light the room to the general level and the bench to the task. Mount the light on the bench frame.

Illuminating Engineering Society recommended light levels for industrial tasks
Task Target, in footcandles
Simple assembly and inspection, large parts 30
Medium parts 50
Difficult assembly and inspection, fine parts 100
Exacting assembly and inspection 300

Exacting inspection calls for 300 footcandles against 30 for simple assembly. No overhead lighting plan delivers both across a floor economically, which is the case for a task light at the bench. The recommendations go up for older workers, faster or more accurate work, and dark parts.

A light fixed to the bench frame stays aimed at the work and moves with an adjustable bench.

Section Nine

Seating and standing

The chair is part of the workstation.

Short answer: Seated for precision and long duration, standing for force and movement, and sit-stand where the bench adjusts easily.

Posture by task
Posture Suits Needs
Seated Precision work, repetition, long duration A chair that reaches the bench height, with feet on the floor or a footring
Standing Force, reach, movement, short cycles A mat on a hard floor
Sit-stand Changing posture through the shift An adjustable bench and a suitable stool

Industrial seating is its own product because the seat has to reach a bench, not a desk. In a cleanroom, an ESD area or a washdown room, the chair has to match the room. See our chairs and stools guide. For standing work, see our anti-fatigue matting guide: softer is not better past a point.

Section Ten

Packing and material flow

A packing station is a bench with a direction of travel.

Short answer: Lay out a packing bench so cartons slide on, across and off with as little lifting as possible.

Decide which way the work flows, where empty cartons and packing material come from, and where finished cartons go. Then place the dispensers, scale and printer in that order.

Section Eleven

Choosing by application

Find the row that matches your situation.

Short answer: Start with the task and who does it. Then the load, the surface and the room.

Heavy mechanical work, striking and pressing
A fixed height welded bench, well above your static load, with a maple or steel top.
One station, several workers or shifts
An adjustable height bench. Electric if the height changes daily.
Seated assembly
A cantilever or open base, with the right chair.
Electronics
An ESD workstation specified as a set.
Many small parts and tools
A bench with modular drawers.
Packing
A packing bench, with a ball transfer top for heavy cartons.
Cleanroom or washdown
A stainless bench, frame included.
Chemicals
An epoxy or stainless top. Tell us the chemicals.
Rough work that ruins tops
A replaceable hardboard top.
Work done at the machine
A mobile bench with locking casters.
A machine or other point load
A machine stand.
Inspection
A bench frame with a task light.
Section Twelve

Common and costly mistakes

Most come from buying the bench before describing the task.

Short answer: Set the height from the task, subtract the fixture, and specify the surface, light and chair with the bench.

Buying every bench at 34 in

Set height from elbow height and the task.

Forgetting the fixture height

Measure to the work.

Reading capacity as a point load

Ratings are for evenly spread loads.

Buying on static capacity for striking work

Buy stiffness.

Maple where chemicals or food are present

It absorbs.

Calling a dissipative top an ESD station

The person, chair, bins and floor count too.

Manual adjustment on a station that changes daily

It will not be adjusted.

No locking casters on a mobile bench

It moves under force.

Relying on ceiling lights for inspection

Add a task light.

Buying the chair from a different budget

The bench and chair heights have to work together.

Section Thirteen

Frequently asked questions

What comes up most often on quote calls.

What height should a workbench be?

Set it from the worker's standing elbow height and the task: about 2 in above the elbow for precision work, 2 in to 4 in below for light work, and 8 in to 16 in below for heavy work. Subtract the height of any fixture or tote the work sits in.

What does a workbench capacity rating mean?

It is the evenly spread load the bench supports. A concentrated load, such as a machine on four feet, is a harsher case and may need a machine stand.

What is the best workbench top?

It depends on the work. Maple suits heavy bench work, stainless suits washdown, epoxy suits chemicals, static-dissipative laminate suits electronics, and a replaceable hardboard top suits rough work.

Do I need an adjustable height workbench?

If several people or shifts share the station, or one person alternates between sitting and standing, yes. Choose electric if the height changes daily.

What makes a workstation ESD safe?

A dissipative worksurface with a path to ground, a grounded worker by wrist strap or ESD footwear and flooring, ESD seating and containers, and regular verification, as set out in ANSI/ESD S20.20.

Four legs or cantilever legs?

Four legs are the most rigid. Cantilever legs leave the front open for seated work, wheelchairs and carts, at some cost in capacity.

How much light does a workbench need?

The Illuminating Engineering Society recommends about 30 footcandles for simple assembly, 50 for medium parts, 100 for difficult work and 300 for exacting inspection.

Are drawers better than shelves under a bench?

For many small parts and tools, yes. A drawer shows everything at once. Rousseau heavy duty drawers are listed at 400 lb each.

Can a mobile workbench be used for heavy work?

Within its rating and with the casters locked. Casters reduce rigidity, so striking and pressing are better done on a fixed bench.

What bench suits a packing station?

A packing bench laid out for the flow of cartons, with a ball transfer top where cartons are heavy.

What bench works in a cleanroom or washdown area?

A stainless steel bench, with a stainless or otherwise washable frame.

Section Fourteen

Quick-reference tables

Published figures referenced in this guide.

Rules of thumb
Item Figure Source
Precision work height About 2 in above elbow height CCOHS
Light work height About 2 in to 4 in below elbow height CCOHS
Heavy work height About 8 in to 16 in below elbow height CCOHS
ESD worksurface Resistance below 1 × 109 ohms ANSI/ESD S20.20
Light for exacting inspection 300 footcandles IES
Before you order

Tell us the task, who does it and for how long, the load and whether it is spread or concentrated, what touches the surface, and the room conditions.

About the author. Tom McGovern has worked in the industrial material handling industry since 1981, bringing over 45 years of hands-on experience helping businesses select the right equipment for their applications. His expertise includes specifying and quoting fixed height and adjustable height workbenches, modular drawer workstations, packing benches and stainless benches.

Questions about this guide? Call 866-333-0728 to speak with an experienced material handling specialist.

Ready for a quote?

Send us these details and a material handling specialist will reply, typically within one business day.

  • Dimensions
    Size of the load and the space it goes in
  • Load
    Weight per item, shelf or level
  • Quantity
    How many units you need
  • Delivery ZIP code
    For freight pricing
  • Drawing
    A sketch, photo or spec sheet, if you have one
Get a Fast Quote Call 866-333-0728

Tell us the task before the bench

What is done at the station, by whom, for how long, and what touches the surface. Those answers set the height, the top and the base. Quotes are reviewed by material handling specialists, typically within one business day.

866-333-0728

Browse workbenches & workstations at custommhs.com

No bots. No guesswork. Real experts.

Sources

Canadian Centre for Occupational Health and Safety (working in a standing position) · ANSI/ESD S20.20 · Illuminating Engineering Society recommended light levels · Rousseau, Pro-Line, Little Giant, Jamco and Strong Hold figures as published on CustomMHS product listings.

Disclaimer. This guide is educational content and reflects the opinion and general experience of CustomMHS. It is not an ergonomic assessment or an ESD program audit. Work height guidelines are general, and your own ESD program and the full standard govern static control. Reviewed November 2026.