Industrial Equipment Experts Since 1980 | Mon–Fri, 7 AM–6 PM ET
No bots. Real experts. 866-333-0728
Get a Fast Quote
Get a Fast Quote

CustomMHS Buyer's Guide

Pallet Racking & Storage Racks

Every capacity quoted for a rack has a condition attached, and the condition is usually in smaller type than the number. Move one beam and the number changes. Here is how rack capacity works and what the standards expect of you as the owner.

Covers: Selective · structural · roll-formed · push-back · flow · cantilever · bulk, bar, reel and die racks Questions: 866-333-0728 Written and reviewed by: Tom McGovern · November 2026
Section One

Every capacity has a condition

The headline number is real. It is also conditional, and the condition is the part that gets lost between the quote and the installation.

Quick answers
  • Frame capacity depends on beam spacing. Move a beam and you have changed the capacity of the rack.
  • Three numbers limit a bay: the frame rating, the beam rating per pair, and the total in the bay. The frame rating governs the bay.
  • L/180 is the beam deflection limit. A 96 in beam may sag about 1/2 in at full load and be within it.
  • Keep the height to the top beam level within six times the frame depth, or have the rack engineered for overturning.
  • Anchor every column, post a load plaque, keep the LARC drawings, and take damaged bays out of service until an engineer has reviewed them.

Take a figure from our listings. A MECO 3 in structural upright frame is rated at 34,800 lb per bay. The rest of the sentence says the rating applies when vertical beam spacing does not exceed 60 in. That condition is the whole basis of the rating.

A column is a slender member. What keeps it from buckling is being braced at intervals by the beams. The governing dimension is the unsupported length: the distance from the floor to the first beam, or the largest spacing between beams, whichever is greater. Widen the spacing and you have made the column longer in the only way that matters structurally.

One published capacity table for a C3 x 3.5 bolted structural column
Beam spacing Listed capacity
36 in to 72 in 27,515 lb
96 in 15,867 lb, about 42% less

Worked example: how a taller load moves a beam

Does the load fit under 60 in beam spacing?
Step Math Result
Load height on the pallet 54 in
Pallet 54 in + 5 in 59 in
Room to lift the pallet off the beam 59 in + 4 in 63 in of clear opening
Beam spacing 63 in + the beam height More than 60 in

With that load, the beam levels end up more than 60 in apart, and the 34,800 lb rating no longer describes the rack. The 4 in lift-off allowance is an example. Use the clearance your trucks and your rack supplier call for.

This is how racks get overloaded without anyone adding weight

Someone takes out a beam level to fit a taller load. Nobody adds weight, and the paperwork still says 34,800 lb. The rack is now rated for less than it was that morning. If you move a beam, have the rack re-rated by whoever engineered it.

Please read this part

This guide is educational and reflects the opinion and general experience of CustomMHS as an equipment distributor. It is not a structural design or a compliance assessment. Rack capacity depends on the engineered configuration, the floor and the location. Ratings are the manufacturers' published figures. Confirm the current data sheet for your exact model before you order.

Section Two

Frame, beam and bay

Three numbers that limit each other. Quoting one as "the capacity" is how orders go wrong.

Short answer: Check each level against the beam rating per pair, then the total in the bay against the frame rating. The lower limit wins.

The three ratings
Rating What it covers Example from our listings
Frame What the two uprights carry in total for the bay, at a stated beam spacing MECO structural: 34,800 lb per bay on 3 in channel, 52,200 lb on 4 in channel
Beam What one level carries, stated per pair of beams, with the load spread evenly See the table below
Bay The total stored between one pair of frames Limited by the frame rating

Worked example. Four beam levels at 10,000 lb each add up to 40,000 lb. On a frame rated at 34,800 lb per bay, the bay limit is 34,800 lb, not 40,000 lb. The floor level, if pallets sit on the slab, does not load the frame.

MECO structural load beams, capacity per pair, as listed
Model Length Channel Capacity per pair
2SB3-48 48 in 3 in 10,000 lb
2SB3-72 72 in 3 in 6,750 lb
2SB4-48 48 in 4 in 17,500 lb
2SB4-96 96 in 4 in 8,750 lb
2SB5-48 48 in 5 in 26,000 lb
2SB5-144 144 in 5 in 9,000 lb

Span costs capacity. Going from a 48 in beam to a 72 in beam in the same 3 in channel drops the level from 10,000 lb to 6,750 lb. Wider bays hold more pallets, and each pallet may have to be lighter. Our pallet rack components guide covers frames, beams and accessories part by part.

Evenly spread means evenly spread

Beam ratings assume the load is spread along the beam. Two pallets side by side on a 96 in beam pair is close to that. One dense item in the middle is not, and the beam sees much more bending for the same weight. If you store concentrated loads, say so when you ask for a quote.

Section Three

What L/180 deflection means

The most quoted number in racking, and often misunderstood.

Short answer: A loaded beam is allowed to sag its length divided by 180. Sag within that limit is normal. Sag that stays after the load comes off means the beam must be replaced.

Allowed deflection = beam length ÷ 180
96 in beam
96 ÷ 180 = 0.53 in, a little over 1/2 in
144 in beam
144 ÷ 180 = 0.80 in, about 13/16 in

The limit comes from the Rack Manufacturers Institute and ANSI MH16.1. RMI explains that it was set as the point where people looking at the rack begin to sense that something is wrong. It is not the point where the beam fails.

  • Visible sag is not automatically an emergency. Half an inch on an 8 ft beam at rated load is within the limit.
  • Meeting L/180 does not prove a beam is safely loaded. Capacity is the measure of overload, not sag. Do not use sag as your load gauge.
The measurement that matters

Normal deflection goes back to zero when the load comes off. A beam that stays bowed after unloading has been permanently bent. Take the load down and replace it.

Section Four

Structural or roll-formed

Two products for two kinds of buildings.

Short answer: Structural rack is hot-rolled channel with bolted beams and takes impact better. Roll-formed rack is lighter, costs less and reconfigures faster.

Hot-rolled channel, bolted

Structural

Welded frames of structural steel channel, with beams bolted on. Heavier, more expensive, and more forgiving of being hit by a fork truck.

Cold-formed steel, teardrop

Roll-formed

Cold-formed sections with punched slots, so beams drop in and lock without bolts. Faster to install and change, and lower in cost for the same rated capacity. See Husky pallet racking.

Both can be engineered to the same number. The real question is what happens when a fork truck hits the rack, and how often that happens in your building. A busy dock with tight aisles damages uprights, and structural rack absorbs that better. A quiet stockroom with wide aisles does not need to pay for it.

Either system adjusts in small vertical steps, and roll-formed does it faster because nothing has to be unbolted. Remember section one: every change in beam elevation changes the capacity.

MECO structural upright frames, 3 in channel, as listed
Model Depth and height Frame weight
SF3-3608 36 in by 8 ft 76 lb
SF3-4212 42 in by 12 ft 129 lb
SF3-4816 48 in by 16 ft 173 lb
SF3-4824 48 in by 24 ft 260 lb
Section Five

Choosing the rack type

Density and access trade against each other.

Short answer: Many items with a few pallets each calls for selective rack. A few items with many pallets each can use a deeper system.

Rack types compared
System Depth Rotation Best for
Selective 1 pallet deep Any pallet, any time Many items. The most common and lowest cost per bay
Double-deep 2 deep Last in, first out More density. Usually needs a deep-reach truck
Drive-in Several deep Last in, first out Few items, many pallets of each. The truck drives into the rack, so damage risk is higher
Drive-through Several deep First in, first out The same idea, loaded from one side and unloaded from the other
Push-back Several deep, on carts Last in, first out Density with access from one aisle. Needs consistent pallets
Pallet flow Many deep, on rollers First in, first out High turnover and date-sensitive stock. Needs good pallets
Cantilever Arms, no front column Not applicable Long goods. See our cantilever guide
The pallet decision and the rack decision go together

Flow and push-back systems are unforgiving about pallet condition. Settle the pallet first. Our pallets guide covers what makes a pallet rackable.

Cost per pallet position leaves out the cost of the building. Denser systems give back floor space, and floor space has rent and utilities attached. Compare systems by cost per position plus the floor area each one uses.

Section Six

Height, depth and the 6 to 1 rule

A simple ratio that tells you when a rack needs more than standard anchoring.

Short answer: Divide the height to the top beam level by the frame depth. At 6 to 1 or less, standard anchoring is normal. Above it, the rack has to be engineered for overturning.

Height to depth ratio = height to the top beam level ÷ frame depth
20 ft on a 42 in frame
240 in ÷ 42 in = 5.7. Within the rule.
24 ft on a 42 in frame
288 in ÷ 42 in = 6.9. Over the rule.
Tallest top beam on a 42 in frame
6 × 42 in = 252 in, or 21 ft
Tallest top beam on a 48 in frame
6 × 48 in = 288 in, or 24 ft

Above 6 to 1, RMI guidance calls for anchors and base plates designed for the overturning force, or ties across the top of the rack rows. You can also come down in height or go to a deeper frame. Measure to the top loaded beam level, not to the top of the steel.

Frame depth follows the pallet

A 48 in deep pallet normally goes on a 42 in deep frame, so the pallet overhangs the front and back beams by about 3 in each. That is intended. The pallet bears on the beams. Tell us which pallet dimension runs front to back.

Section Seven

Anchoring and the floor

The least glamorous line on the quote, and the one that decides whether an impact becomes an incident.

Short answer: ANSI MH16.1 calls for every column to have a base plate and to be anchored to the floor. The slab is part of the rack.

Anchors and base plates resist the forces at the bottom of the column, which in a real building means fork truck impact and, in some regions, earthquakes. Under ANSI MH16.1, every pallet rack column has a base plate and is anchored to the floor. The number and size of anchors are set by the manufacturer or a professional engineer for the installation.

The floor is part of the rack

An anchor is only as good as the slab it is in. Thin slabs, cracked slabs and joints under a base plate all reduce what the anchor can hold. Find out your slab thickness and condition before the rack is designed.

Seismic design is an input, not an upgrade

Seismic requirements depend on location and are built into the design from the start. They affect the anchors, the base plates, the bracing and sometimes the whole layout. Tell us the installation address.

Column protectors do not replace anchors

Protectors reduce damage from glancing hits in busy aisles. They do not hold the rack down. Our barriers and guarding guide covers guard rail and bollards for aisle ends.

Section Eight

Load plaques, LARC drawings and the R-Mark

The paperwork is the part buyers skip, and it carries your position as the owner.

Short answer: Ask for load plaques for every configuration, the LARC drawings, and whether the design is R-Mark certified.

ANSI MH16.1, Design, Testing and Utilization of Industrial Steel Storage Racks, is the governing standard for pallet rack. Cantilever rack has its own standard, ANSI MH16.3. For drive-in, drive-through and portable racks, ask which standard the design follows.

The load plaque

The plaque tells everyone near the rack what it can hold. MH16.1 calls for it to be at least 50 square inches, placed where it is easy to see, and to show the maximum permissible unit load or the maximum evenly spread load per level, the average unit load if it applies, and the maximum total load per bay.

Change the rack and the plaque is wrong

If the rack is reconfigured or altered, the plaque no longer applies. The owner has the manufacturer or a qualified engineer re-evaluate the capacity and post new plaques.

  • LARC drawings: Load Application and Rack Configuration drawings record the engineered configuration your capacities belong to. Keep them.
  • The R-Mark: the Rack Manufacturers Institute certification that a manufacturer's capacity tables and designs have been reviewed against the RMI and ANSI standard.
  • Stamped engineering: for a substantial installation, ask for documents sealed by a registered engineer. Many building departments require them for a permit.
Section Nine

What OSHA says

Very little by name, and that matters.

Short answer: OSHA has no rack-specific standard. It cites rack hazards under 1910.176(b) and the General Duty Clause, and looks to ANSI MH16.1.

29 CFR 1910.176(b) requires that storage of material not create a hazard and that stored material be stable and secure against sliding or collapse. Beyond that, OSHA uses the General Duty Clause, Section 5(a)(1) of the OSH Act, which requires a workplace free of recognized hazards. An industry consensus standard such as ANSI MH16.1 is evidence of what a recognized hazard is.

In practice, treat MH16.1 as the working requirement: plaques posted, columns anchored, damage repaired, and changes re-engineered. That is also how you avoid dropping several tons of inventory on somebody. Your authority having jurisdiction and your safety staff decide what applies to your site.

Section Ten

Wire decking and point loads

A low-cost accessory that solves several problems, if it is matched to the rack.

Short answer: Wire decks are rated for evenly spread loads, not point loads, and are not made to be stood on. Order them to the beam profile and the level rating.

Wire decking spans the beams and turns an open bay into a supported surface. It keeps small items from falling through, lets sprinkler water and light pass, and supports pallets that are not rated for open-beam racking. The standard for welded wire rack decking is ANSI MH26.2.

  • Evenly spread loads only. A deck rating assumes the load covers the deck. A heavy part on four small feet is a point load and can bow or fail a deck that is not engineered for it.
  • Nobody stands on it. Wire decking is not made to be walked on. If people need to get onto a level, that is a work platform question. See our ladders and platforms guide.
  • Edge styles. Waterfall decks fold over the front and back beams. Flush styles sit inside a step in the beam.
  • Match the deck to the rack. Give the frame depth, the beam profile, the beam length and the level capacity when you order.
Section Eleven

Damage, inspection and out-of-plumb

Racking rarely fails because it was under-specified. It fails because it was hit and left.

Short answer: A loaded rack may lean no more than 1/2 in per 10 ft. Inspect on a schedule, and unload and isolate any damaged bay until it is evaluated.

Maximum lean of a loaded rack = height ÷ 240, which is 1/2 in per 10 ft
16 ft frame
192 in ÷ 240 = 0.8 in, about 13/16 in
20 ft frame
240 in ÷ 240 = 1 in

You can check this with a plumb line and a tape. RMI guidance is that the owner sets a regular inspection program, and that a damaged rack is unloaded and taken out of service until a qualified engineer has evaluated it and repairs are made.

The reporting problem is the real problem

Most serious rack incidents start with a driver who hit an upright, saw nothing obvious and said nothing. A dented column has lost capacity you cannot see from a truck seat. The most effective control is a rule people believe: report every hit, and nobody is disciplined for reporting.

  • Columns: dents, bows, twists and damage at the base plate. Aisle-end columns take the most hits.
  • Anchors: missing, loose or pulled.
  • Beams: sag that does not recover, damaged connectors, missing safety clips or bolts.
  • Bracing: bent or missing diagonals and horizontals.
  • Plaques: present, readable and matching the rack as it stands.
Section Twelve

Specialty racking

When the load is long, round, heavy or awkward, standard pallet rack is not the answer.

Short answer: Use cantilever for long goods, bulk rack for hand-stacked cartons, bar and sheet racks for stock, reel racks for cable, and roll-out shelves for dies.

Cantilever

Arms on a central column store lumber, pipe, bar and sheet with no front column in the way. See MECO cantilever racking and our cantilever racking guide.

Bulk storage rack

Wide-span rack with shelf decking for hand-stacked cartons and loose goods. The Hallowell bulk rack with steel decking is listed at 3,800 lb per shelf. See also Hallowell boltless and reinforced bolted high-capacity racks.

Bar and sheet storage

MECO horizontal bar racks for long stock pulled by length, vertical bar racks where floor space is tighter than ceiling height, and vertical sheet racks for sheet metal, plywood and panels stored on edge.

Portable stacking racks

MECO portable U-racks and modular stackable racks stack on each other and can be moved or removed when a job ends.

Reel storage

MECO heavy duty reel racks hold cable and wire reels on axles so they pay out in place. MECO reel winders support a reel on rollers.

Carton flow

The carton flow rack system feeds cartons to the pick face on rollers, first in, first out.

Roll-out die shelving

A die is small, very dense and valuable, and on a fixed shelf there is no way to get a hook or a fork onto it. On pull-out heavy-duty die racks, the shelf rolls out so the die can be lifted from above. The listing publishes 2,000 lb per shelf at full extension. Our roll-out die racks guide covers them.

Tool storage

Rousseau mini-racking is high-density storage for CNC tooling.

Section Thirteen

Choosing by application

Find the row that matches your situation.

Short answer: Start with how many items you store and how fast they turn. Then check the building: height, floor and location.

Many items, a few pallets of each
Selective rack.
Few items, many pallets of each, last in first out is fine
Push-back or drive-in.
Date-sensitive or high-turnover stock
Pallet flow, with good pallets.
A busy dock with frequent impacts
Structural rack, with column protection and aisle-end guards.
A stockroom that changes often
Roll-formed rack.
Loads taller than usual
Work out the beam spacing first, then ask for the frame capacity at that spacing.
A tall rack on a shallow frame
Check the 6 to 1 ratio. Go deeper, lower, or have it engineered.
Cartons, small items or mixed pallets on a level
Wire decking matched to the beams and the level rating.
Long stock
Cantilever or bar racks.
Dies and molds
Roll-out die shelving.
Cable and wire reels
Reel racks.
Hand-stacked cartons
Bulk storage rack.
An earthquake region
Give us the address so the design includes seismic loads from the start.
Section Fourteen

Common and costly mistakes

Most of these happen after the rack is installed.

Short answer: Do not move beams without re-rating, do not add up beam ratings to get a bay rating, and do not leave damage in service.

Moving a beam and keeping the old capacity

Beam spacing sets the frame capacity.

Adding beam ratings to get the bay rating

The frame rating governs the bay.

Putting a concentrated load on a beam pair or a wire deck

Ratings assume an evenly spread load.

Using sag as a load gauge

L/180 is a deflection limit, not a capacity check.

Going tall on a shallow frame

Check 6 to 1.

Skipping anchors or ignoring the slab

Every column is anchored, and the slab has to hold the anchor.

No plaque, or a plaque for a rack that has changed

Post one for every configuration.

Leaving a hit upright in service

Unload it and have it evaluated.

Buying pallets and rack separately

Flow and push-back need consistent, sound pallets.

Section Fifteen

Frequently asked questions

What comes up most often on quote calls.

What determines pallet rack capacity?

Three ratings: the frame rating for the bay, the beam rating per pair for each level, and the total stored in the bay. The frame rating depends on beam spacing, so it changes when a beam is moved.

Can I move a beam level myself?

You can physically move it, but doing so changes the unsupported length of the column and the frame capacity. Have the manufacturer or a qualified engineer confirm the new capacity and update the load plaque.

What does L/180 mean?

It is the beam deflection limit: the beam length divided by 180. A 96 in beam may deflect about 0.53 in at full rated load and be within the limit.

Is a sagging beam dangerous?

Sag within L/180 under load is normal. A beam that stays bowed after the load is removed has been permanently bent and should be replaced.

Structural or roll-formed pallet rack?

Structural rack uses hot-rolled channel with bolted beams and stands up to impact better. Roll-formed rack costs less and reconfigures faster. Choose by how often the rack is likely to be hit.

What is the 6 to 1 rule?

The height to the top beam level divided by the frame depth should not exceed 6 with standard anchoring. A 42 in deep frame reaches that at 21 ft. Above it, the rack needs anchoring engineered for overturning or ties at the top.

Does pallet rack have to be anchored?

Yes. ANSI MH16.1 calls for every column to have a base plate and to be anchored to the floor.

Does OSHA require a load plaque?

OSHA has no rack-specific standard, but ANSI MH16.1 calls for load plaques, and OSHA cites rack hazards under 1910.176(b) and the General Duty Clause. Post a plaque for every configuration.

What are LARC drawings?

Load Application and Rack Configuration drawings. They record the engineered layout and loads your rack capacities are based on. The owner keeps them.

Can I stand on wire decking?

No. Wire decking is rated for evenly spread stored loads and is not made to be walked on.

How much can a rack lean?

A loaded rack may be out of plumb by no more than 1/2 in per 10 ft of height, which is 1 in on a 20 ft frame.

Section Sixteen

Quick-reference tables

Rules and listings referenced in this guide.

Rules of thumb and limits
Item Figure Source
Beam deflection limit Beam length ÷ 180 RMI, ANSI MH16.1
Out-of-plumb limit, loaded 1/2 in per 10 ft RMI, ANSI MH16.1
Height to depth 6 to 1 with standard anchoring RMI guidance
Anchoring Every column, with a base plate ANSI MH16.1
Load plaque At least 50 square inches ANSI MH16.1
Cantilever rack Separate standard ANSI MH16.3
Wire decking Separate standard ANSI MH26.2
OSHA Secure storage, General Duty Clause 29 CFR 1910.176(b), OSH Act 5(a)(1)
What we list
Family Listing
Roll-formed pallet rack Husky pallet racking
Frames, beams and accessories See our pallet rack components guide
Cantilever MECO cantilever racking
Bulk rack Hallowell bulk rack, boltless, reinforced bolted
Bar and sheet racks Horizontal, vertical bar, vertical sheet
Stacking racks U-racks, modular stackable racks
Reels Reel racks, reel winders
Die racks, carton flow, tool storage Pull-out die racks, carton flow, mini-racking
Before you order

Tell us the pallet size and weight, the load height, the number of levels, the clear ceiling height, the truck you use and the installation address. Ask for the frame capacity at your beam spacing, load plaques and LARC drawings.

About the author. Tom McGovern has worked in the industrial material handling industry since 1981, bringing over 45 years of hands-on experience helping businesses select the right equipment for their applications. His expertise includes specifying and quoting pallet racking, cantilever racking, bulk rack, bar and sheet racks and die racks.

Questions about this guide? Call 866-333-0728 to speak with an experienced material handling specialist.

Ready for a quote?

Send us these details and a material handling specialist will reply, typically within one business day.

  • Dimensions
    Size of the load and the space it goes in
  • Load
    Weight per item, shelf or level
  • Quantity
    How many units you need
  • Delivery ZIP code
    For freight pricing
  • Drawing
    A sketch, photo or spec sheet, if you have one
Get a Fast Quote Call 866-333-0728

Tell us the pallet, the load height and the address

Pallet size and weight, load height, levels, ceiling height, truck and location. With those we can quote a rack with the right capacity at your beam spacing. Quotes are reviewed by material handling specialists, typically within one business day.

866-333-0728

Browse racking at custommhs.com

No bots. No guesswork. Real experts.

Sources

ANSI MH16.1, MH16.3 and MH26.2 · Rack Manufacturers Institute guidance · OSHA 29 CFR 1910.176(b) and the General Duty Clause · MECO and Hallowell figures as published on CustomMHS product listings.

Disclaimer. This guide is educational content and reflects the opinion and general experience of CustomMHS. It is not a structural design or a compliance assessment. Rack capacity depends on the engineered configuration, the floor slab and the location, including seismic requirements. Have the manufacturer or a qualified engineer confirm capacity for your layout, and check permit requirements with your building department. Reviewed November 2026.