Industrial Equipment Experts Since 1980 | Mon–Fri, 7 AM–6 PM ET
No bots. Real experts. 866-333-0728
Get a Fast Quote
Get a Fast Quote

CustomMHS Buyer's Guide

Lift Tables & Pallet Positioners

Two numbers decide most of this purchase, and only one is on the front of the brochure. Capacity is easy. Collapsed height decides whether you can get the load onto the table at all.

Covers: Autoquip · Presto-Lifts · Bishamon · Blue Giant · Lift Products Questions: 866-333-0728 Written and reviewed by: Tom McGovern · November 2026
Section One

Collapsed height first

Buyers start with capacity and raised height. Start with how low the table goes, because that decides whether the load can get on it.

Quick answers
  • Collapsed height decides how you load the table. A pallet jack needs a floor level table, which lowers to about 3/8 in, or a U-shaped or roll-in design.
  • A load that rolls on is harder on the table than a load set on it. Published guidance adds 50% to each axle load.
  • An oversized platform costs capacity at the edges: about 2% per inch beyond the minimum platform size, in each direction.
  • For hand stacking and unstacking of pallets, a self-leveling positioner with a turntable is usually a better answer than a powered table.
  • Never work under a raised platform without the maintenance device in place and the power locked out.

Lift table travel is stated as a range, such as 7.5 in to 70 in. The first number is the collapsed height. A pallet jack's wheels stay on the floor, so it cannot set a pallet on a platform that sits 7 in high without a ramp or a pit.

Collapsed height decides the loading method
Collapsed height You load it with Format
3/8 in to 2 in A pallet jack rolled straight on, or by walking the load on Floor level
About 3 in to 5 in A fork truck, or a pallet jack with a ramp Low profile
About 5 in to 9-1/2 in A fork truck, a hoist, a conveyor or by hand Standard scissor

This is the most expensive mistake in the category, because there is no simple fix. A standard table delivered where a floor level table was needed gets a ramp, a pit, or a replacement.

The question to answer first

Stand where the table will go and ask what brings the load to it: pallet jack, fork truck, conveyor, hoist or a person. That answer sets the collapsed height before you look at a single capacity figure.

Please read this part

This guide is educational and reflects the opinion and general experience of CustomMHS as an equipment distributor. It is not an engineering specification or a compliance assessment. The sizing rules are published industry guidance. Travel and capacity ranges are the manufacturers' published figures and can change. Confirm the current data sheet for your exact model before you order.

Section Two

Rolling loads are not static loads

If anything rolls onto the table, the rated capacity is not the number to compare against.

Short answer: Multiply each axle load by 1.5, then compare. A 2,000 lb two-axle cart loads the table like a 3,000 lb static load.

A capacity rating describes a load placed on the platform and sitting there. When a wheeled load rolls on, impact and movement add force. Published scissor lift application guidance puts a number on it: increase axle loads by 50%.

Static equivalent = axle load × 1.5
2,000 lb two-axle cart, evenly loaded
1,000 lb per axle
Each axle
1,000 × 1.5 = 1,500 lb
Both axles on the table
3,000 lb static equivalent

Comparing that cart's 2,000 lb to a 2,000 lb table rating looks fine and is not.

Fork trucks are a different conversation

A loaded fork truck does not split its weight evenly. The same guidance notes that 80% to 90% of the total weight can sit on the front axle. Multiply that by 1.5 and it is far beyond a catalog selection. If a fork truck will ever drive onto your table, tell us so the manufacturer can rate it for that.

Tell us if anything rolls on

Pallet jacks, carts and fork trucks all change the sizing. Give the weight and the number of axles.

Section Three

Platform size costs capacity

A bigger top is not just a bigger price. It reduces what the table can carry at its edges.

Short answer: Edge-load capacity drops about 2% for every inch the platform is wider or longer than the minimum size for that model.

Edge-load capacity falls about 2% per inch beyond the minimum platform size, in each direction
6 in wider than the minimum
6 × 2% = 12% less edge-load capacity
12 in wider
12 × 2% = 24% less
24 in wider
24 × 2% = 48% less

The reason is leverage. The scissor legs support the platform at fixed points, and every inch of overhang gives a load at the edge a longer lever.

Buy the platform you need, not the one that looks generous. If you do need a large top, say so, and the manufacturer will size the scissor legs for it instead of stretching a standard model.

Section Four

End loading and side loading

A scissor lift is not equally strong in every direction.

Short answer: Load over the ends where you can. If you must load over the side, ask for a wide base or extra wide model.

The scissor legs run the length of the table, so most designs are much stronger over the ends than over the sides.

  • Load and unload over the ends where you can. It costs nothing if you plan it before the table is installed.
  • If you must load over the side, say so. Wide base and extra wide models widen the leg stance for that. See Presto-Lifts Wide Base and Autoquip Series 35 Extra Wide.

Loads that do not cover the platform

The load's center of gravity has to stay inside the outline of the supporting legs, including while the load is moving onto a raised platform. A load set to one side, or only partly on the table, can put its center of gravity outside that outline even when the weight is well within the rating.

Section Five

Travel and capacity, and the trade between them

The range is very wide. The strongest table and the tallest table are rarely the same machine.

Short answer: Across the lines we carry, capacity runs from 250 lb to 24,000 lb and travel from 3/8 in to 94 in. Those extremes do not come together.

The shape of the range, as listed
Family Travel Capacity What it shows
Autoquip Series 35 Double Long 6.5 in to 72 in 4,000 to 24,000 lb Highest capacity, moderate travel
Autoquip TorkLift 6 in to 84.75 in 2,200 to 20,000 lb High capacity and high travel
Autoquip Compact 5 in to 94 in 500 to 12,000 lb Highest travel in the range
Presto-Lifts Double Scissors 6 in to 86 in 500 to 4,000 lb Height, at lower capacity
Blue Giant Zero Ground Level 3/8 in to 36.5 in 2,000 to 4,000 lb Lowest collapsed height
Bishamon Compact 5 in to 54.25 in 440 to 1,650 lb Light duty, small footprint

Worked example: how much raised height do you need?

You want the bottom layer of a pallet at a 30 in working height. The pallet deck is about 5 in above its base.

Raised height for a 30 in working height
Step Math Result
Working height wanted 30 in
Less the pallet 30 in − 5 in 25 in
Raised platform height to ask for At least 25 in

Most standard tables cover that easily, so the choice comes back to collapsed height, capacity and platform size.

Double scissor

A double scissor stacks two leg sets to reach higher, up to 86 in in the lines we carry. It costs capacity and stability compared with a single scissor of the same footprint. Use it when you need the height.

Narrow and wide versions

Extra narrow models fit tight spaces. Wide base and extra wide models add stability and side-load capacity. For a brand-by-brand comparison, see our scissor lift tables by brand guide.

Section Six

Standard, low profile or floor level

Three formats, separated almost entirely by how far down they go.

Short answer: Standard tables give the most choice and value. Low profile tables start near 3 in. Floor level tables start near 3/8 in and take a pallet jack with no ramp or pit.

Standard

Collapsed about 5 in to 9-1/2 in

The widest choice of capacity and travel. Right when the load arrives by fork truck, hoist or hand. See Autoquip Series 35, Presto-Lifts XL, Bishamon Alpha and Blue Giant Standard Duty.

Low profile

Collapsed about 3 in to 5 in

A low starting height that makes loading easier. See Autoquip, Bishamon and Lift Products low profile tables.

Floor level

Collapsed as low as 3/8 in

A pallet jack rolls straight on. See Blue Giant Zero Ground Level, Presto-Lifts Floor Level and Presto-Lifts P4.

U-shaped and roll-in designs

A U-shaped platform lets a pallet jack drive into the U with the pallet, lower it onto the platform, and back out. The jack never lifts the pallet onto anything. See the Lift Products U-Lift and the Presto-Lifts roll-in U-lift. These work with open-bottom pallets and skids, so check your pallets.

Price a floor level table before you dig a pit

A standard table in a floor pit also loads flush. It means concrete work, drainage, a table you cannot move, and a hole in the floor if you ever remove it. A floor level table gets the same result without touching the slab.

Section Seven

Self-leveling positioners

The product in this category that needs no operator input at all.

Short answer: A self-leveling positioner keeps the top of the pallet at working height as layers are added or removed. Match it to your real pallet weight range.

A self-leveling pallet positioner uses springs or air to hold the top of a pallet at a steady height. As cases come off and the load gets lighter, the platform rises. As a pallet is built, it sinks.

Stacking and unstacking by hand takes a worker from the floor to shoulder height on every pallet. The bottom layers are the worst, a deep bend with a load in the hands. A positioner removes that range, and because it needs no button, it cannot be skipped when people are in a hurry.

  • Match the weight range. A spring or air setting chosen for heavy pallets will not respond properly to light ones. Tell us your lightest and heaviest pallet.
  • Air or spring. Air units need a compressed air connection and adjust by pressure. Spring units need no utilities.
  • Add rotation if people walk around the pallet. See the next section.

We list the Bishamon EZ-Loader, the Presto-Lifts P3-AA, the Lift Products air self-leveling positioner and the Blue Giant automatic pallet positioner. For self-leveling carts on wheels, see our mobile lift equipment guide.

Section Eight

Turntables and rotation

The other half of the pallet-building problem.

Short answer: Height is one problem and reach is the other. A turntable brings the far side of the pallet to the worker.

Someone building or breaking down a pallet has to reach all four sides. Without rotation they walk around it or twist and over-reach, and twisting while lifting is a reliable way to hurt a back.

Self-leveling plus rotation is the complete answer for hand stacking: the top layer stays at working height and the working face comes to the operator.

Try a portable turntable first

If you are not sure a turntable will change habits, a portable one lets you test it at several stations before you commit.

Section Nine

Stainless and washdown

A lift table is a hydraulic machine with many moving parts. Wet areas are hard on it.

Short answer: Stainless and galvanized versions are listed. Confirm that the hydraulics are protected and ask how the scissor area drains.

We list the Lift Products SXT stainless steel lift table and stainless and galvanized Guardian tables. What to confirm beyond the finish:

  • Are the cylinder and hydraulics protected? A stainless top on a standard mechanism is not a washdown machine.
  • Does the stainless grade suit your cleaning chemicals? See our cleanroom and stainless guide.
  • How does the scissor area drain?
  • Is accordion skirting available? It keeps water and debris out and guards the pinch points.
Section Ten

Safety and ANSI MH29.1

This equipment raises heavy loads on a mechanism full of closing gaps. There is a standard for it.

Short answer: Before anyone works under the platform: load off, platform lowered, maintenance device in place, pressure relieved, power locked out.

ANSI MH29.1, Safety Requirements for Industrial Scissors Lifts, covers stationary and mobile scissor lifts used to position, feed, transfer, load or unload material or people. It sets out responsibilities for manufacturers, owners and users. Some of those sit with you as the owner.

The rule people break

The most dangerous thing anyone does around a lift table is reach under a raised platform. Before adjustment or repair:

  1. Remove the load and lower the platform completely where the work allows.
  2. Secure the maintenance device or blocking so the platform cannot move.
  3. Relieve the system pressure before disconnecting anything.
  4. Disable the controls.
  5. Disconnect the power and follow your lockout and tagout procedure.
Order the maintenance device with the table

A maintenance prop only helps if it is there, fits that model, and is kept on the machine.

  • Toe guards or skirting to close the pinch points as the scissor comes down.
  • Guard rails and gates where people ride or work on the raised platform. See our ladders and platforms guide.
  • A firm, level floor. The standard assumes one.

This is a summary. The standard is copyrighted and contains much more. If lift tables are central to your operation, buy it and read it.

Section Eleven

Choosing by application

Find the row that matches your situation.

Short answer: Start with how the load arrives, then whether it rolls on, then capacity and height.

Loads arrive by pallet jack
A floor level table, or a U-shaped or roll-in design.
Loads arrive by fork truck
A standard scissor table. Widest choice and best value.
A cart or pallet jack rolls onto the table
Multiply the axle loads by 1.5 before comparing to the rating, and tell us it is a rolling load.
A fork truck drives onto the table
Call us. This needs the manufacturer's rating for that use.
Hand stacking or unstacking pallets
A self-leveling positioner, ideally with a turntable.
People walk around a pallet
A turntable, floor mounted or portable.
Loading over the side
A wide base or extra wide model.
An oversized platform
Say so up front, so the legs are sized for it.
Very heavy loads, 10,000 lb and up
Autoquip Series 35 heavy families and TorkLift. Expect moderate travel at those capacities.
Height over 70 in
A double scissor or a tall compact family, at lower capacity.
Food, pharmaceutical or washdown
Stainless or galvanized versions. Confirm the hydraulics are protected.
The table has to move between stations
The Autoquip Series 35 Rover mobile lift table.
Tipping a container toward the worker
Section Twelve

Common and costly mistakes

The first four cost real money or cause injuries.

Short answer: Check collapsed height, rolling loads, fork truck use and maintenance blocking before anything else.

Choosing on raised height and ignoring collapsed height

Collapsed height decides how the load gets on.

Comparing a rolling load to a static rating

Axle loads need a 50% increase.

Assuming a fork truck's weight splits evenly

A loaded truck can carry 80% to 90% on the front axle.

Working under a raised platform without the maintenance device

Load off, lowered, blocked, pressure relieved, locked out.

Oversizing the platform without asking

About 2% of edge-load capacity per inch beyond the minimum.

Loading over the side on a standard model

Scissor lifts are stronger over the ends.

Buying a powered table where a positioner was the answer

A powered table helps only when someone presses the button.

Digging a pit before pricing a floor level table

The floor level table often does the same job without concrete work.

Section Thirteen

Frequently asked questions

What comes up most often on quote calls.

What is the most important spec on a lift table?

Collapsed height. It decides how the load gets onto the table. A pallet jack needs a floor level table that lowers to about 3/8 in, or a U-shaped or roll-in design. A standard table that collapses to 5 in or more is loaded by fork truck, hoist or hand.

Can I compare my cart's weight directly to the table's capacity?

No. Published guidance increases axle loads by 50% for impact. A 2,000 lb two-axle cart puts 1,000 lb on each axle, which becomes 1,500 lb per axle, or the equivalent of a 3,000 lb static load.

Can a fork truck drive onto a lift table?

Only onto a table rated for it. A loaded fork truck can carry 80% to 90% of its weight on the front axle, and that load is then increased for impact. Tell us before you order.

Does a bigger platform cost anything besides money?

Yes. Edge-load capacity drops about 2% for every inch the platform is wider or longer than the minimum size for the model. A platform 24 in wider loses about 48% of its edge-load rating.

Does it matter which side I load from?

Yes. Most scissor lifts are much stronger over the ends than over the sides. If you must load over the side, ask for a wide base or extra wide model.

What is a self-leveling positioner?

It is a spring or air unit that keeps the top of a pallet at a steady working height. The platform rises as the load gets lighter and sinks as it gets heavier, with no controls to operate.

Air or spring self-leveling?

Air units need a compressed air connection and adjust by pressure. Spring units need no utilities. Either way, match the unit to your lightest and heaviest pallet.

Do I need a turntable?

If people walk around a pallet or twist to reach the far side, yes. A turntable brings the working face to the operator.

Should I put a standard lift table in a pit?

Price a floor level table first. A pit means concrete work, drainage and a table you cannot move. A floor level table loads flush without touching the slab.

What standard covers lift tables?

ANSI MH29.1, Safety Requirements for Industrial Scissors Lifts.

What has to happen before someone works under the platform?

Remove the load, lower the platform, secure the maintenance device or blocking, relieve the system pressure, disable the controls, and disconnect the power under your lockout procedure.

Section Fourteen

Quick-reference tables

Published figures referenced in this guide.

Sizing rules
Rule Figure
Rolling load Axle load × 1.5
Loaded fork truck 80% to 90% of the weight on the front axle
Oversized platform About 2% of edge-load capacity per inch, each direction
Direction Much stronger over the ends than the sides
Off-center loads Center of gravity stays inside the leg outline
Standard ANSI MH29.1
Listed ranges by family
Family Travel Capacity
Autoquip Series 35 Double Long 6.5 in to 72 in 4,000 to 24,000 lb
Autoquip TorkLift 6 in to 84.75 in 2,200 to 20,000 lb
Autoquip Series 35 Extra Wide 6.5 in to 72 in 2,500 to 15,000 lb
Autoquip Compact 5 in to 94 in 500 to 12,000 lb
Autoquip Series 35 Extra Narrow 6.5 in to 90 in 2,500 to 4,000 lb
Presto-Lifts XL-Series 7.25 in to 57 in 2,000 to 8,000 lb
Presto-Lifts Wide Base 7.75 in to 70 in 2,000 to 8,000 lb
Presto-Lifts Double Scissors 6 in to 86 in 500 to 4,000 lb
Bishamon Alpha 8.5 in to 60 in 2,200 to 6,600 lb
Blue Giant Standard Duty 7.5 in to 70 in 2,000 to 6,000 lb
Bishamon Low Profile 2.9 in to 39.4 in 550 to 4,400 lb
Blue Giant Zero Ground Level 3/8 in to 36.5 in 2,000 to 4,000 lb
Presto-Lifts Floor Level 3/8 in to 35-3/8 in 2,000 to 6,000 lb
Lift Products U-Lift 3-1/8 in to 33-7/8 in 2,200 to 3,300 lb
Lift Products SXT stainless 9 in to 36 in 4,000 lb
Bishamon EZ-Loader 9.63 in to 30.5 in 250 to 3,500 lb
Presto-Lifts P3-AA 9.5 in to 27.75 in 400 to 4,500 lb
Presto-Lifts LPT turntable Floor level 4,000 lb
Bishamon floor mount turntable Floor level 4,500 lb
Lift Products Roto-Max 6.5 in to 32.5 in 2,500 to 3,500 lb
Before you order

Confirm capacity, rolling load rating and platform size against the listing and the manufacturer's data for the exact model. Tell us how the load arrives, whether anything rolls on, the platform size and which way loads travel.

About the author. Tom McGovern has worked in the industrial material handling industry since 1981, bringing over 45 years of hands-on experience helping businesses select the right equipment for their applications. His expertise includes specifying and quoting scissor lift tables, floor level lifts, self-leveling positioners and pallet turntables.

Questions about this guide? Call 866-333-0728 to speak with an experienced material handling specialist.

Ready for a quote?

Send us these details and a material handling specialist will reply, typically within one business day.

  • Dimensions
    Size of the load and the space it goes in
  • Load
    Weight per item, shelf or level
  • Quantity
    How many units you need
  • Delivery ZIP code
    For freight pricing
  • Drawing
    A sketch, photo or spec sheet, if you have one
Get a Fast Quote Call 866-333-0728

Tell us how the load gets on

Pallet jack, fork truck, hoist or by hand. That answer sets the collapsed height before capacity is even discussed. Quotes are reviewed by material handling specialists, typically within one business day.

866-333-0728

Browse lift tables at custommhs.com

No bots. No guesswork. Real experts.

Sources

ANSI MH29.1 Safety Requirements for Industrial Scissors Lifts · published scissor lift application guidance (Advance Lifts) for rolling loads, platform size and directional strength · Autoquip, Presto-Lifts, Bishamon, Blue Giant and Lift Products figures as published on CustomMHS product listings.

Disclaimer. This guide is educational content and reflects the opinion and general experience of CustomMHS. It is not an engineering specification or a compliance assessment. Sizing rules are industry guidance, so confirm them against the manufacturer's data for your model and application. ANSI MH29.1 is copyrighted and contains more than is summarized here. Reviewed November 2026.