Industrial Equipment Experts Since 1980 | Mon–Fri, 7 AM–6 PM ET
No bots. Real experts. 866-333-0728
Get a Fast Quote
Get a Fast Quote

CustomMHS Buyer's Guide

Industrial Shelving

Most people assume open and closed shelving are the same unit with panels added. They are not. Closed units in our listings carry nearly twice what open ones do, because the panels are structure. That fact changes how you shop, and it meets a fire code question few buyers hear about.

Covers: Hallowell · Little Giant · Metro · Rousseau · steel, wire and polymer shelving Questions: 866-333-0728 Written and reviewed by: Tom McGovern · November 2026
Section One

Closed carries more than open

The side and back panels are not trim. They are the bracing.

Quick answers
  • Closed steel shelving carries more than open. In our Hallowell listings, closed units go up to 2,200 lb per shelf and open units up to 1,250 lb.
  • A shelf rating assumes the load is spread evenly, and the whole unit has its own lower limit. Metro wire shelving is 800 lb per shelf and 2,000 lb per unit.
  • Fire codes treat storage as shelving up to 30 in deep, with 30 in aisles, up to 15 ft high. Past that it is treated as rack.
  • Anchor any unit taller than four times its depth. An 18 in deep unit reaches that at 6 ft.
  • Chrome wire is for dry rooms. Use epoxy, stainless or polymer in coolers and wet areas.

The common picture of closed shelving is an open unit with panels added to keep dust off. The listed capacities say otherwise. A panel across the back and sides stops the frame from racking sideways far better than a diagonal brace does, and the capacity goes up with it.

Listed capacity per shelf, steel shelving families
Family Capacity per shelf
Hallowell Hi-Tech open shelving Up to 1,250 lb
Little Giant all-welded shelving 2,000 lb
Hallowell closed shelving Up to 2,200 lb
Hallowell high capacity boltless Up to 2,300 lb
Hallowell reinforced bolted Up to 2,800 lb
Hallowell bulk rack, steel decking Up to 3,800 lb
Why this matters when you compare quotes

Two quotes for "36 by 18, five shelves" may be one open unit and one closed unit. They are not the same product. Compare the per-shelf ratings.

There is a catch

Closing in a unit makes every shelf a solid surface that sprinkler water cannot fall through. In a sprinklered building that is a fire protection question. Read section four before you buy closed units in quantity.

Please read this part

This guide is educational and reflects the opinion and general experience of CustomMHS as an equipment distributor. It is not a fire protection or structural assessment. Fire code requirements depend on your building and your authority having jurisdiction. Capacities are the manufacturers' published figures. Confirm the current data sheet for your exact model before you order.

Section Two

Reading a per-shelf rating

Three qualifiers hide inside every shelving capacity.

Short answer: The rating assumes an evenly spread load, the unit has its own total limit, and "up to" is the best case in the family.

The three qualifiers
Phrase What it means
Evenly distributed The load covers the shelf. The same weight in one spot bends the shelf much more
Per shelf Not per unit. The posts and frame have their own total limit
Up to The best figure in the family. A wider shelf in the same family carries less. Check the rating for your exact size

Worked example: per shelf against per unit

Metro wire shelving, five shelves
Step Math Result
Shelf rating As listed 800 lb per shelf, evenly distributed
Five shelves at the shelf rating 5 × 800 4,000 lb
Unit rating, stationary As listed 2,000 lb
Average you can load 2,000 ÷ 5 400 lb per shelf
Point loads are the most common overload

Dies, castings, motors and anything on small feet put their weight on a few square inches. A shelf rated at 2,000 lb evenly spread may not take a 900 lb die on four contact points. If you store concentrated loads, tell us, and see our Hallowell high capacity boltless and reinforced bolted shelving.

A drawer is rated differently. Rousseau modular drawer shelving is listed at 400 lb per drawer, and that figure includes the slides. Do not compare a drawer rating to a shelf rating.

Section Three

The 30, 30 and 15 rule

There is a defined line where shelving becomes rack in fire protection terms.

Short answer: NFPA 13 treats storage as shelf storage on structures up to 30 in deep with aisles at least 30 in wide, up to 15 ft high.

NFPA 13, the sprinkler standard, defines shelf storage as storage on structures up to and including 30 in deep, separated by aisles at least 30 in wide. Its shelf storage provisions apply up to 15 ft of storage height.

Inside and outside the definition
Dimensions How it is treated
Inside 30 in deep or less, 30 in aisles or more, 15 ft high or less Shelf storage
Outside Deeper, tighter aisles, or taller Treated as rack storage, which can bring in-rack sprinklers into the picture

Back-to-back rows

NFPA 13 also defines back-to-back shelf storage: two rows up to 30 in deep each, no more than 60 in in total, separated by a solid vertical barrier such as plywood, particleboard or sheet metal, with no flue space between them, up to 15 ft high.

Worked example. Two 30 in deep units back to back are 30 in + 30 in = 60 in deep. With the vertical barrier between them, the run can stay inside the shelf storage definition. Without it, you have a 60 in deep structure, which is outside.

Price the fire protection before the layout

If your layout is drifting toward 36 in deep units, 24 in aisles or 16 ft heights, ask your fire protection engineer what that changes before you commit. A 30 in deep unit with a proper aisle is often the lower total cost.

Section Four

Solid shelves and sprinklers

A sprinkler works by getting water down onto the fire. A solid shelf is a roof.

Short answer: Open wire lets water through. Large areas of solid shelving can change the sprinkler protection a building needs. Ask before you buy.

This is the other side of section one. Closed and solid-deck shelving is stronger and keeps dust off the stock. In fire protection terms it is an obstruction. NFPA 13 has specific rules for solid shelving in racks, including in-rack sprinklers under solid shelves in some arrangements, and it also counts loads placed so that they block the openings water needs.

  • Open wire is the friendliest choice. Water and light pass through it.
  • Solid shelves in small numbers are a different matter from an entire aisle of closed units.
  • Mixed units help. MetroMax polymer units can combine open grid shelves with a solid one, so containment goes only where it is needed.
  • Ask first. Give your fire protection contact the shelf type, depth, aisle width and height. In many buildings the answer is that nothing changes.

Flue spaces and in-rack sprinklers are the rack version of this question. See our pallet racking guide.

Section Five

How the shelf attaches

Four connection systems. The choice sets capacity, assembly time and how easily you can change the layout.

Short answer: Boltless is fast and flexible, bolted is strong and takes dividers, welded has nothing to loosen, and wire shelving adjusts fastest.

Fast and flexible

Boltless

Beams lock in without tools. Takes particleboard, wire or steel decking. Our Hallowell high capacity boltless line is listed at up to 2,300 lb per shelf.

Strong and divided

Bolted with clips

Shelves sit on clips with added bracing and take dividers, which suits compartment storage. Our Hallowell reinforced bolted line is listed at up to 2,800 lb per shelf.

Nothing to loosen

All-welded

Arrives assembled. Little Giant welded shelving is listed at 2,000 lb per shelf, with a three-sided retaining lip version at the same rating. Shelf heights are fixed, and freight costs more because it ships assembled.

Post and sleeve

Wire shelving

Grooved posts and split sleeves lock each shelf by wedging. The fastest system to rearrange, which is why wire shelving is common in stockrooms where the product mix changes.

Choose by how often you will change it

If the layout is settled and the loads are heavy, welded or bolted is right. If you do not know what will be on the shelves in a year, buy the adjustable system.

Section Six

The 4 to 1 rule and anchoring

Shelving tips before it collapses, and the arithmetic takes ten seconds.

Short answer: Divide the unit height by its depth. Above 4, anchor it or pair it back to back.

Height to depth ratio = unit height ÷ unit depth. Above 4 to 1, anchor the unit.
87 in high, 18 in deep
87 ÷ 18 = 4.8. Over. Anchor it.
The same units back to back
Depth becomes 36 in. 87 ÷ 36 = 2.4. Inside the rule.
Tallest 18 in deep unit at 4 to 1
4 × 18 in = 72 in, or 6 ft
Tallest 24 in deep unit at 4 to 1
4 × 24 in = 96 in, or 8 ft

The 4 to 1 figure is common shelving manufacturer guidance. Racking uses 6 to 1. Follow the installation instructions for your unit, and local seismic rules where they apply.

Two rows bolted together back to back act as one unit with the combined depth. That is why a back-to-back run in the middle of the floor is stable at heights where a single row would need anchors.

The failure is usually a person

Shelving tips when someone loads the top shelf heavily or climbs it. Put heavy items low, keep the top shelf light, and make it clear that shelving is not a ladder. Our ladders and platforms guide covers the right equipment.

Section Seven

Wire shelving and finishes

The finish decides whether the unit survives the room.

Short answer: Chrome is for dry storage. Green or gray epoxy is for coolers, freezers and damp rooms. Stainless is for sterile and washdown areas.

Wire shelving lets air, light and sprinkler water through, and you can see what is on it from across the room. Metro wire shelving is published at up to 800 lb per shelf evenly distributed and up to 2,000 lb per stationary unit. See wire shelving units.

Wire finishes
Finish Where it belongs Note
Chrome Dry storage only NSF listed for dry environments. In a cooler it rusts
Green epoxy Coolers, freezers, high humidity Published with a 15 year warranty against rust
Gray epoxy The same protection in customer-facing areas Published with the same 15 year rust warranty
Stainless, type 304 or 316 Sterile, cleanroom and washdown areas The most durable, and the highest cost

Type 316 stainless resists chlorides, which means salt, bleach and many disinfectants, better than type 304. Our cleanroom and stainless guide covers the choice.

Buying wire shelving as parts

Wire systems are also sold as shelves, posts, casters and dividers. You can add a level, split a unit, or put a stationary unit on casters. A mobile unit is rated lower than a stationary one, so check the rating after you add casters.

Section Eight

Polymer shelving

The higher-priced option that is often the lower-cost one in a wet room.

Short answer: Polymer shelving does not rust. MetroMax i is listed at 2,000 lb per shelf, MetroMax 4 and MetroMax Q at 800 lb.

MetroMax polymer lines, as published
Line Capacity per shelf Corrosion warranty
MetroMax i 2,000 lb Lifetime
MetroMax 4 800 lb Lifetime
MetroMax Q 800 lb 20 years

The top line matches an all-welded steel shelf, so polymer is not automatically the light-duty choice. See MetroMax polymer shelving units, MetroMax shelves and posts and Metro solid shelves.

  • Open grid drains and lets air through. The default in a cooler or washdown room.
  • Solid grid contains spills and wipes clean.
  • Removable shelf mats lift out for washing. Where your sanitation program needs verified cleaning, this is the feature you are buying.
  • Antimicrobial protection is built into the shelf material to slow the growth of mold, mildew and bacteria on the shelf itself. It does not replace cleaning.
Section Nine

Food, pharmaceutical and washdown

One number drives a lot of food storage decisions.

Short answer: The FDA Food Code calls for food to be stored at least 6 in above the floor. Dunnage racks are the simplest way to do it.

The FDA Food Code, adopted in some form by most state and local regulators, calls for food to be stored at least 6 in above the floor. It lets staff clean underneath, see spills and pests, and keeps product out of floor moisture. Check your local code for exceptions.

That number is why dunnage racks exist. A dunnage rack is a low platform that keeps sacks, cases and bulk containers off the floor with air underneath. See dunnage racks.

Dunnage rack capacities as listed
Type Capacity
Aluminum, 4000 series Up to 5,000 lb
Aluminum, 2000 series Up to 4,000 lb
Polymer bow tie Up to 3,000 lb
Aluminum, economy Up to 2,000 lb
Wire shelf, stationary Up to 1,600 lb
Aluminum with handle Up to 1,000 lb
Wire shelf, mobile Up to 800 lb
NSF listing depends on the finish

Chrome wire is NSF listed for dry environments only. In a cooler it rusts, and rust on shelving in a food area is an inspection finding. Use epoxy, stainless or polymer there.

Wall mounted stainless shelving and tables keep the floor clear for cleaning in tight prep areas. Confirm that the wall can carry the load before you order.

Section Ten

Getting more storage from the same floor

Most shelving floor space is aisle.

Short answer: High-density track shelving removes all but one aisle. Back-to-back rows are the low-cost first step.

Worked example: a room 20 ft wide

18 in deep shelving rows across a 20 ft (240 in) room
Layout Math Rows
Static rows, each with its own 36 in aisle 240 in ÷ (18 in + 36 in) 4 rows
High-density on tracks, one 36 in aisle (240 in − 36 in) ÷ 18 in 11 rows

The Metro Top-Track high-density system puts units on an overhead track so an aisle opens wherever you need it. The trade is access: only one aisle is open at a time. It suits archives, stockrooms and spare parts, where one person picks at a time. It is a poor fit where several people pick at once.

  • Back-to-back rows halve the aisles for the same number of rows and improve stability.
  • Use the height between the top shelf and the ceiling, within the 15 ft and 4 to 1 limits.
  • Units on casters roll out of the way. Check the lower mobile rating.
Section Eleven

Specialty shelving

Where a plain shelf is the wrong tool.

Short answer: Use drawers for many small parts, bins for divided parts, security units for controlled stock, and tool shelving for CNC holders.

Modular drawer shelving

Rousseau modular drawer shelving puts drawers inside a shelving frame, listed at 400 lb per drawer. A drawer shows all of its contents at once, where a deep shelf hides everything behind the front row. Our Rousseau drawer shelving guide covers it.

Bin shelving

Hallowell closed bin shelving gives each part its own opening. Our small parts bins guide covers the bins.

Security shelving

Metro security shelving is an enclosed, lockable wire unit for high-value or controlled stock.

CNC tool storage

Rousseau CNC tool shelving, tool cabinets and mini-racking hold tool holders by the taper and keep them apart.

Retaining lip shelving

Little Giant welded shelving with three-sided lips, 2,000 lb per shelf, keeps items from sliding off the back and ends.

Machine and work stands

A machine is a concentrated load on four feet, which is what a shelf is not built for. See heavy-duty machine stands and Jamco stainless work stands.

Section Twelve

Choosing by application

Find the row that matches your situation.

Short answer: Start with the room: dry, damp, cold or washdown. Then the load per shelf and how often the layout changes.

Dry stockroom, product mix changes
Chrome wire shelving.
Walk-in cooler or freezer
Epoxy-coated wire or polymer.
Washdown, food or pharmaceutical
Polymer or stainless.
Heavy parts, 1,000 lb and up per shelf
Closed, boltless high-capacity, reinforced bolted or welded steel shelving.
Dies and concentrated loads
High capacity die shelving, and tell us the load and its footprint.
Many small parts
Drawer shelving or bin shelving.
Bags and cases on a food storeroom floor
Dunnage racks.
Too little floor for the stock
Back-to-back rows first, then a high-density track system.
High-value stock
Security shelving.
A sprinklered warehouse, many closed units
Ask your fire protection engineer before you order.
Tall, shallow units against a wall
Anchor anything over 4 to 1.
Section Thirteen

Common and costly mistakes

Each has a simple fix at the quote stage.

Short answer: Compare per-shelf ratings, respect the unit rating, match the finish to the room, and anchor tall units.

Comparing open and closed units as the same product

The panels are bracing.

Multiplying the shelf rating by the number of shelves

The unit has its own limit.

Reading "up to" as your shelf

Check the rating for your size.

Putting a point load on an evenly rated shelf

Tell us about dies, motors and castings.

Going deeper than 30 in or tighter than 30 in aisles without asking

That can change the fire protection.

Filling a sprinklered building with solid shelves

Ask first.

Chrome wire in a cooler

It rusts. Use epoxy, stainless or polymer.

Skipping anchors on tall, shallow units

Above 4 to 1, anchor or pair back to back.

Storing food on the floor

Six inches up, on a dunnage rack or shelf.

Section Fourteen

Frequently asked questions

What comes up most often on quote calls.

Is closed shelving stronger than open shelving?

Yes. The side and back panels brace the frame. In our Hallowell listings, closed shelving is rated up to 2,200 lb per shelf and open shelving up to 1,250 lb.

What does "evenly distributed" mean on a shelf rating?

The rating assumes the load is spread across the whole shelf. The same weight concentrated in one spot bends the shelf more and can overload it.

Can I load every shelf to its rating?

Not always. The unit has a total rating too. Metro wire shelving is 800 lb per shelf but 2,000 lb per stationary unit, so five shelves average 400 lb each.

What is the 30, 30 and 15 rule?

NFPA 13 defines shelf storage as structures up to 30 in deep with aisles at least 30 in wide, with provisions up to 15 ft of storage height. Deeper, tighter or taller storage is treated as rack storage.

Do solid shelves affect sprinklers?

They can. Solid shelves block sprinkler water, and NFPA 13 has specific requirements for solid shelving in racks. Ask your fire protection engineer before buying closed or solid-deck units in quantity.

When does shelving need to be anchored?

Common manufacturer guidance is to anchor any unit taller than four times its depth. An 18 in deep unit reaches that at 6 ft, and a 24 in deep unit at 8 ft. Back-to-back rows bolted together count their combined depth.

Can I use chrome wire shelving in a cooler?

No. Chrome is for dry storage. Use green or gray epoxy, stainless or polymer in coolers, freezers and damp rooms.

Is polymer shelving strong enough for heavy loads?

MetroMax i is published at 2,000 lb per shelf. MetroMax 4 and MetroMax Q are published at 800 lb per shelf.

How high off the floor does food have to be stored?

The FDA Food Code calls for at least 6 in. Check your local code for exceptions.

What is high-density shelving?

Shelving units on a track that slide together, leaving one movable aisle. In a 20 ft wide room, 18 in deep rows go from four static rows to eleven.

Boltless, bolted or welded?

Boltless is quick to assemble and adjust. Bolted with clips is stronger and takes dividers. Welded arrives assembled with fixed shelf heights and nothing to work loose.

Section Fifteen

Quick-reference tables

Published figures referenced in this guide.

Capacity per shelf, as listed
Family Capacity per shelf
Hallowell Hi-Tech open shelving Up to 1,250 lb
Little Giant all-welded shelving 2,000 lb
Hallowell closed shelving Up to 2,200 lb
Hallowell high capacity boltless Up to 2,300 lb
Hallowell reinforced bolted Up to 2,800 lb
Hallowell bulk rack, steel decking Up to 3,800 lb
Metro wire shelving 800 lb, 2,000 lb per stationary unit
MetroMax i polymer 2,000 lb
MetroMax 4 and MetroMax Q polymer 800 lb
Rousseau drawer shelving 400 lb per drawer
Rules and references
Rule Figure Source
Shelf storage 30 in deep, 30 in aisles, 15 ft high NFPA 13
Back-to-back shelf storage 60 in total depth with a solid vertical barrier NFPA 13
Anchoring Above 4 to 1 height to depth Shelving manufacturer guidance
Food storage height At least 6 in above the floor FDA Food Code
Before you order

Tell us what goes on each shelf and what it weighs, the room conditions, the unit size and height, and whether the units stand alone, back to back or against a wall.

About the author. Tom McGovern has worked in the industrial material handling industry since 1981, bringing over 45 years of hands-on experience helping businesses select the right equipment for their applications. His expertise includes specifying and quoting open and closed steel shelving, wire shelving, polymer shelving, die shelving and dunnage racks.

Questions about this guide? Call 866-333-0728 to speak with an experienced material handling specialist.

Ready for a quote?

Send us these details and a material handling specialist will reply, typically within one business day.

  • Dimensions
    Size of the load and the space it goes in
  • Load
    Weight per item, shelf or level
  • Quantity
    How many units you need
  • Delivery ZIP code
    For freight pricing
  • Drawing
    A sketch, photo or spec sheet, if you have one
Get a Fast Quote Call 866-333-0728

Tell us what goes on the shelf and what room it is in

Load per shelf, whether it is spread or concentrated, dry or wet, and how tall. Those answers pick the shelving. Quotes are reviewed by material handling specialists, typically within one business day.

866-333-0728

Browse shelving at custommhs.com

No bots. No guesswork. Real experts.

Sources

NFPA 13 · FDA Food Code · Hallowell, Little Giant, Metro and Rousseau figures as published on CustomMHS product listings.

Disclaimer. This guide is educational content and reflects the opinion and general experience of CustomMHS. It is not a fire protection or structural assessment. Sprinkler and storage requirements depend on your building, your stored goods and your authority having jurisdiction. Confirm capacities for the exact size you order. Reviewed November 2026.