Industrial Equipment Experts Since 1980 | Mon–Fri, 7 AM–6 PM ET
No bots. Real experts. 866-333-0728
Get a Fast Quote
Get a Fast Quote

CustomMHS Buyer's Guide

Modular Drawer Carts & Tool Cabinet Carts

A drawer cart is a drawer cabinet that has to survive being pushed across a plant floor while loaded. The drawer rating, the casters and the depth matter more than the drawer count. Get those three right and the rest is configuration.

Covers: Rousseau R-Series and L-Series carts · Strong Hold · Jamco · Little Giant Questions: 866-333-0728 Written and reviewed by: Tom McGovern · November 2026
Section One

What a drawer cart is for

Bringing the tool crib to the job, and the cases where that is the wrong idea.

Quick answers
  • Rousseau R-Series carts carry 400 lb per drawer. L-Series carts carry 100 lb per drawer. Choose by the heaviest drawer you will load.
  • The drawer rating is not the cart rating. The loaded cart has to stay inside the caster rating: 440 lb per 4 in caster and 1,100 lb per 6 in caster on Rousseau carts.
  • Allow the cart depth, plus the open drawer, plus about 30 in for a person. A 27 in deep cart needs close to 7 ft.
  • A stainless top on a painted cart is not a washdown cart. For washdown, buy a stainless cart.
  • Never move a cart with a drawer open. Order the drawer lock-in.

A tool cart earns its price by removing trips. A technician who walks from the press to the crib and back three times on one changeover has spent the time the cart was supposed to save. A cart that holds the whole kit, organized so a missing tool is obvious, makes it one trip.

That only works if the cart holds what the job needs and moves easily when full. The two common failures are opposites: a cart too small for the kit, and a cart so heavy and wide that nobody wants to push it.

Buy a drawer cart

The kit has to travel

Maintenance response, die changes, machine setups and line-side kitting.

Buy a stationary cabinet

The kit stays put

Tool cribs and parts storage that never roll. See our R-Series cabinet guide.

Buy a service cart

The load is loose and changes

Parts, cartons and totes with nothing to organize. See our carts guide.

Please read this part

This guide is educational and reflects the opinion and general experience of CustomMHS as an equipment distributor. Sizes, drawer ratings and caster ratings are the manufacturers' published figures. Confirm the current data sheet for your exact model before you order.

Section Two

The four kinds of cart

They look alike in a photo and solve different problems.

Short answer: Modular drawer carts for many small items, steel tool carts for maintenance work, mobile cabinets for bulky items, and stainless carts for washdown.

Mobile tool storage by type
Type Lines Inside Choose it when
Modular drawer carts Rousseau R-Series (400 lb drawers) and L-Series (100 lb drawers) Full-extension drawers in chosen heights, with or without partitions Many small items that each need a place
Steel tool carts with drawers Strong Hold 3, 5, 6 and 12-drawer carts and the maintenance cart Fixed drawer sets and a heavy plate top A maintenance cart that takes abuse and doubles as a bench
Mobile cabinets Little Giant 48 in mobile cabinets, Strong Hold visible and countertop cabinets Shelves and locking doors, one drawer or none Bulky items and cased power tools
Stainless carts Strong Hold 4-TC-261-VS-SS, Jamco YV-Series Stainless body and shelves Washdown, food and pharmaceutical areas
Check what is inside the cabinet

Several mobile cabinets have no drawers. If you need divided drawer storage, a shelf and door cabinet is the wrong product whatever its capacity.

Section Three

400 lb or 100 lb per drawer

The Rousseau R-Series and L-Series look alike. The drawer rating is the difference.

Short answer: If any drawer will hold dense tooling, buy the R-Series. If every drawer holds hand tools and light parts, the L-Series does the job for less.

Rousseau R-Series carts

400 lb per drawer

  • Widths from 24 in to 72 in
  • Single-bank carts and wide multi-drawer carts
  • Roll-out shelf and door options on some widths
  • Lifetime warranty on the drawer rolling system, per Rousseau

Rousseau L-Series carts

100 lb per drawer

  • Listed in 18 in, 36 in and 54 in widths
  • 21 in and 27 in depths
  • Heights from 29-1/4 in to 45-1/4 in
  • Lock-in safety and central locking listed as standard

The test is the heaviest single drawer. A drawer of collets, toolholders, die components or steel fixture plates gets heavy fast, and that drawer decides the line. A light drawer loaded with heavy tooling fails months later as a drawer that sags or binds.

The drawer rating is not the cart rating

A 400 lb rating covers one drawer and its slides. Six drawers do not make a 2,400 lb cart. Rousseau does not publish a total cart capacity for its drawer carts. It publishes the caster rating, and the loaded cart has to stay inside it. See section eight.

Section Four

Reading a Rousseau cart model number

The same logic as the stationary cabinets, with a different series letter.

Short answer: The first five characters give the line, width and depth. The four digits give the height group and drawer mix.

R5BHE-3001
R5B
R-Series single-bank drawer cart. Multi-drawer carts use R5G or R5D. L-Series carts use L3B
H
Width: H is 48 in
E
Depth: E is 24 in
3001
Height group and drawer mix. Odd and even numbers usually pair as partitioned and open

R5BHE-3001 is a 48 in wide, 24 in deep cart, 37-1/2 in tall, with two 3 in, three 4 in and one 8 in drawer, partitioned. R5BHE-3002 is the same cart with open drawers.

Width and depth codes on the Rousseau cart listings
Code As the width (4th character) As the depth (5th character)
B 18 in (L-Series) Not used
C 24 in 18 in
D 30 in 21 in
E 36 in 24 in
G Not used 27 in
H 48 in Not used
J 54 in (L-Series) Not used
K 60 in Not used

So R5BDG is 30 in by 27 in, R5BEC is 36 in by 18 in, and L3BED is an L-Series 36 in by 21 in cart. The 72 in multi-drawer cart is R5XLE and does not follow the same width letter. The same configuration number usually carries the same drawer mix across widths, but not always, so confirm the mix and height on the listing.

Section Five

Choosing width

Wide enough for the longest item, narrow enough that someone will push it.

Short answer: Measure the longest item that lies flat and add 2 in. Then measure the narrowest doorway on the route. Buy the first width that clears both.

Rousseau drawer cart widths we list
Width Line Depths Good for
18 in L-Series 21 in, 27 in One technician's cart, tight cells
24 in R-Series 21 in, 27 in Compact 400 lb drawers beside one machine
30 in R-Series 21 in, 27 in The practical middle, with the widest choice of layouts
36 in and 36 in L-Series R-Series and L-Series 18 in, 24 in (R). 21 in, 27 in (L) General maintenance and setup
48 in and 48 in multi-drawer R-Series 24 in, 27 in Long tooling stored flat, complete setup kits
54 in L-Series 21 in, 27 in High drawer count at 100 lb
60 in and 60 in multi-drawer R-Series 24 in, 27 in Wide fixtures and dies, or two drawer columns
72 in R-Series multi-drawer 24 in The largest kits

Worked example. The longest item is a 31 in boring bar. 31 in + 2 in = 33 in of inside drawer width, so look at a 36 in cart or wider. The doorway to the cell is 40 in clear. A 36 in cart passes. A 48 in cart does not, unless it goes through lengthwise.

At 48 in and 60 in there are two designs. A single-bank cart (R5B) has full-width drawers for long items. A multi-drawer cart (R5G, R5D) splits the width into drawer columns for more separate drawers.

Section Six

Depth, aisles and drawer projection

A cart gets parked in the aisle. Plan for the drawer that is open in it.

Short answer: Working space is the cart depth, plus the open drawer, plus about 30 in for a person.

Working space = cart depth + drawer projection + room for a person
27 in deep cart
27 + 25 + 30 = 82 in, or 6 ft 10 in
21 in deep cart
21 + 19 + 30 = 70 in, or 5 ft 10 in

Rousseau lists cart depths of 18 in, 21 in, 24 in and 27 in, though not every depth at every width. The drawers are full extension, so an open drawer sticks out about its own depth.

The 27 in depth adds real drawer volume and suits long tools and fixture plates that run front to back. It is also harder to fit beside a machine and harder to steer. Take the deeper cart when the contents need it.

Section Seven

Height and the drawer mix

Cart height stays near bench height. The drawer mix is where the cart earns its price.

Short answer: Count drawers, not inches. Size each drawer to its tallest item plus about 1 in, and put heavy drawers lowest.

Rousseau lists R-Series mobile heights from about 33 in to 47 in depending on width and configuration, and L-Series carts from 29-1/4 in to 45-1/4 in. The single-bank R-Series carts at 48 in and 60 in are 37-1/2 in tall. A cart pushed while loaded has to stay low enough to see over and stable at a floor joint. Take the height from the listing.

Same footprint, different carts. Listed R5BHE configurations, 48 in wide, 24 in deep, 37-1/2 in high
Model Drawer mix Drawers Best for
R5BHE-3001 Two 3 in, three 4 in, one 8 in 6 Small tooling and inserts, with one deep drawer
R5BHE-3003 One each of 3, 4, 5, 6 and 8 in 5 Mixed kits
R5BHE-3009 Two 4 in, three 6 in 5 Hand tools and fittings
R5BHE-3015 One 3 in, three 6 in, roll-out shelf 4 and a shelf A cart that needs a pull-out work surface
R5BHE-3013 One 6 in drawer over a door section 1 and a door Mostly enclosed storage
Sizing a drawer
Drawer height Holds
3 in Inserts, taps, drills, small gauges
4 in to 6 in Hand tools, wrenches, sockets, fittings
6 in to 8 in Collets and toolholders standing up, meters in foam
8 in to 12 in Heavy fixtures and power tools. Keep them lowest
Door or roll-out shelf Cased power tools and anything no drawer suits

Most configurations come partitioned or open under consecutive numbers. Choose open only when a drawer holds one kind of thing or will be foamed. On a cart, every push slides loose parts to the back of an open drawer.

Section Eight

Casters, handles and moving a loaded cart

The part of the cart that decides whether it moves.

Short answer: Add the empty weight and the contents, and compare the total to the caster rating. Checking against three casters instead of four is a sound habit.

Listed caster details by line
Line Casters Brake or floor lock
Rousseau R-Series carts 4 in or 6 in polyurethane. Rousseau rates the 4 in at 440 lb and the 6 in at 1,100 lb Swivel with total-lock brake available. RB8E directional locking pedal optional
Strong Hold tool carts 6 in by 2 in polyurethane on the 5 and 6-drawer carts and the maintenance cart Brakes listed
Strong Hold stainless cart 8 in by 2 in polyurethane swivel Brakes listed
Jamco YV-Series 5 in polyurethane See listing
Little Giant mobile cabinets Confirm on the quote Floor lock listed

Worked example: check the casters

A Rousseau cart on four 4 in casters
Step Math Result
Four casters at 440 lb 4 × 440 1,760 lb
Three casters, the cautious check 3 × 440 1,320 lb
Your load Empty cart weight + contents, drawer by drawer Keep it under 1,320 lb
On 6 in casters, three-caster check 3 × 1,100 3,300 lb

Checking against three casters is a cautious habit, not a manufacturer rating. A floor joint or a dropped bolt lifts one wheel. A cart can also be within its caster rating and still be hard to push. Larger wheels roll over joints more easily, so choose 6 in casters for long runs and ramps.

  • RB90 side handle: a wide-grip aluminum handle.
  • RB92 front handles: for 24 in and 30 in wide single cabinets.
  • RB8E directional locking pedal: locks the swivel so the cart tracks straight.
  • RB88 extended base: Rousseau recommends it when a cabinet has fewer than four drawers or the load is uneven.
Never push with a drawer open

A full-extension drawer moves the cart's center of gravity forward by its whole depth. Close every drawer before moving, and order the lock-in.

Section Nine

Steel tool carts and mobile cabinets

Fixed layouts, heavy plate tops and high cart ratings.

Short answer: Choose a welded steel cart when the cart is also the bench and the contents are heavy and few.

Strong Hold drawer tool carts as listed
Model Size, W by D by H Drawers Listed ratings
3-TC-241-2/5-1DB 36 by 24 by 36 in Two 13 by 20 by 6 in and one 29 by 20 by 6 in Up to 400 lb per drawer
3-TC-240-4/5-1DB 36 by 24 by 36 in Four half-width and one full-width, 6 in high 400 lb per drawer. 539 lb empty
4-TC-241-6/5DB 48 by 24 by 36 in Five 4 in and one 6 in 400 lb per drawer. 600 lb shelf. 592 lb empty
4-TC-240-12/5DB 48 by 24 by 36 in Twelve drawers Confirm the drawer rating on the quote
5-TC-3D-242-12/5DB maintenance cart 61 by 24 by 34 in Ten 4 in and two 6 in, plus a side compartment 400 lb per drawer. 934 lb empty

The listed Strong Hold carts have a 12 gauge body and a 7 gauge top, and most use a 3-point lock that takes a padlock.

Mobile cabinets as listed
Product Construction Listed capacity Storage
Little Giant 48 in mobile cabinets and with locking doors All-welded 12 gauge steel 3,600 lb Locking doors, a padlockable drawer, or both by model
Little Giant 48 in mobile bench cabinet All-welded 12 gauge steel 3,600 lb Center shelf, with a choice of top
Strong Hold visible tool storage cart 12 gauge body, 7 gauge top 1,200 lb shelf capacity Three adjustable shelves, fork pockets
Strong Hold countertop cabinets 12 gauge body 1,900 lb per shelf Two adjustable shelves
Section Ten

Stainless steel carts

A stainless top is not a stainless cart.

Short answer: For washdown, food and pharmaceutical areas, buy a cart that is stainless throughout, and ask for the grade in writing.

Stainless carts as listed
Model Size Construction Listed ratings
Strong Hold 4-TC-261-VS-SS 48 in wide, 26 in deep, 41 in high 12 gauge stainless body, 7 gauge top and side vise shelf 2,000 lb cart capacity. 8 in by 2 in swivel casters with brakes
Jamco YV136 18 in by 36 in by 34 in 16 gauge polished stainless, 3-sided 1,200 lb. 5 in casters
Jamco YV236 24 in by 36 in by 34 in 16 gauge polished stainless, 3-sided 1,200 lb. 5 in casters
The stainless top trap

The Rousseau RC35 stainless top is brushed stainless over a particle board core, 1-3/4 in thick, for painted steel carts. It makes a clean work surface. It does not make the cart suitable for washdown.

If your sanitation program or customer audit names a stainless grade, ask for it in writing at quote time. Our cleanroom and stainless guide covers grades.

Section Eleven

Tops, liners and foam

For Rousseau carts. Low cost on the order, awkward to add later.

Short answer: Pick the top for the work done on the cart, and decide drawer by drawer between partitions and foam.

Rousseau tops, liners and foam
Item What it is for
Laminated wood butcher block top A forgiving surface for bench work
Steel top with non-slip rubber mat Takes impact while the mat grips parts
Galvanized steel top Corrosion resistance in humid areas
Stainless steel top, RC35 A clean work surface. 16 gauge or 12 gauge
Marine edge stainless top A raised edge that contains spills
PVC drawer liner, RG40 Basic protection for the drawer bottom
Foam liner, RG41 1/4 in foam. Cannot be used with partitions or dividers
Tool foam, RG42 A pocket for each tool, so a missing one shows
Collet foam, RG43 Holds collets upright and apart

The RC35 stainless top is listed in 30 by 27, 36 by 24, 48 by 24, 48 by 27, 60 by 24, 60 by 27, 72 by 24 and 72 by 27 in sizes. If your cart is another size and you want a stainless top, confirm it before you order the cart.

Foam the drawers that hold controlled or precision tooling and order the rest partitioned. Buying partitions and then foaming every drawer pays for partitions you will remove.

Section Twelve

Locks and drawer safety

Security for the contents, and drawers that stay shut in transit.

Short answer: Order the drawer lock-in on any cart, and decide the keying before you order.

Rousseau locking and safety options
Part What it does
L3 Key lock for all drawers at once
L50 Code lock with a 4 to 8 digit code
L100 Keyless unlocking by NFC tag or smartphone
LP Hasp that locks all drawers with a padlock
RB10 Padlock bar for all drawers, usable against a wall
RB15 Prevents more than one drawer from opening at a time
Integrated lock-in Keeps a drawer from opening by itself

On a cart the lock-in is not optional in practice. A drawer that rolls open at a floor joint shifts the load and can tip a loaded cart. Strong Hold carts use a 3-point lock with padlock provision, and you supply the padlock.

Decide keying before you order

Keyed alike, keyed differently or master keyed costs nothing to specify and is a nuisance to change. Shared maintenance carts usually want keyed alike with a master. Carts with controlled tooling want separate keys or a code lock you can change.

Section Thirteen

Common and costly mistakes

What goes wrong on drawer cart orders.

Short answer: Choose the line by the heaviest drawer, check the casters, measure the route, and close the drawers before moving.

Buying the L-Series for heavy tooling

The heaviest drawer decides the line.

Reading the drawer rating as the cart rating

Check the loaded weight against the casters.

Choosing width without measuring the route

A cart that will not fit through the doorway is a stationary cabinet.

Buying a cabinet when you needed drawers

Several mobile cabinets have one drawer or none.

Treating a stainless top as a stainless cart

Washdown areas need a stainless cart.

Ordering open drawers for mixed contents

Every push slides loose parts to the back.

Foaming drawers ordered with partitions

The foam liner cannot be used with partitions.

Loading heavy drawers high

Heavy items go lowest.

Moving the cart with a drawer open

Order the lock-in and close every drawer.

Comparing quotes by outside size

Compare full model numbers, including the configuration digits.

Section Fourteen

Frequently asked questions

The questions that come up most on drawer cart quotes.

What is the difference between the Rousseau R-Series and L-Series carts?

The drawer rating. R-Series carts carry 400 lb per drawer and are offered from 24 in to 72 in wide. L-Series carts are listed at 100 lb per drawer in 18 in, 36 in and 54 in widths. Choose by the heaviest drawer you will load.

How much weight can a drawer cart carry in total?

Rousseau does not publish a total capacity for its drawer carts. The limit for the loaded cart is the casters: 440 lb per 4 in caster and 1,100 lb per 6 in caster. Some Strong Hold and Little Giant units list a cart capacity, such as 2,000 lb on the Strong Hold stainless cart and 3,600 lb on the Little Giant 48 in mobile cabinets.

What do the letters in a Rousseau cart model number mean?

R5B is an R-Series single-bank cart, R5G and R5D are multi-drawer carts, and L3B is an L-Series cart. The fourth character is the width (C 24, D 30, E 36, H 48, K 60 in) and the fifth is the depth (C 18, D 21, E 24, G 27 in). The four digits give the height group and drawer mix.

Should I order drawers partitioned or open?

Partitioned for any drawer with mixed items, because a moving cart slides loose parts to the back. Open for drawers that hold one large item or will be foamed.

What casters do the carts use?

Rousseau lists 4 in and 6 in polyurethane casters in fixed, swivel and swivel with total-lock brake versions. Strong Hold lists 6 in by 2 in casters with brakes on its 5 and 6-drawer carts and 8 in by 2 in casters on its stainless cart. Jamco lists 5 in casters on the YV-Series.

How wide an aisle do I need?

Allow the cart depth, plus about the drawer depth for an open drawer, plus about 30 in for the person. A 27 in deep cart needs close to 7 ft, and a 21 in deep cart about 70 in.

Is a cart with a stainless top suitable for washdown?

No. The Rousseau RC35 top is stainless over a particle board core on a painted steel cart. For washdown, choose a stainless cart such as the Strong Hold 4-TC-261-VS-SS or the Jamco YV-Series.

What stainless grade are the stainless carts?

The grade is not on the listings. Strong Hold lists 12 gauge stainless and Jamco lists 16 gauge polished stainless. If your program names a grade, ask for it in writing.

Can I add foam to a partitioned drawer?

No. The RG41 foam liner cannot be used with partitions or dividers. Decide drawer by drawer.

Do I need the drawer lock-in?

Yes on a cart. It keeps drawers from rolling open while the cart moves, which can shift the load and tip the cart.

When should I buy a steel tool cart instead of a modular drawer cart?

When the cart is also the bench, the contents are heavy and few, and the layout will not change. Choose a modular drawer cart for many small items or when you want to pick the drawer heights.

Section Fifteen

Quick-reference tables

The numbers worth having on one screen.

Key figures
Item Listed
Rousseau R-Series drawer 400 lb
Rousseau L-Series drawer 100 lb
Rousseau 4 in caster 440 lb
Rousseau 6 in caster 1,100 lb
Strong Hold drawer, most models 400 lb
Strong Hold stainless cart 2,000 lb
Little Giant 48 in mobile cabinets 3,600 lb
Jamco YV-Series 1,200 lb
What we list
Type Listings
Rousseau R-Series carts 24 in, 30 in, 36 in, 48 in, 60 in, 72 in
Rousseau L-Series carts 18 in, 36 in, 54 in
Strong Hold tool carts 3-drawer, 5-drawer, 6-drawer, 12-drawer, maintenance cart
Mobile cabinets Little Giant 48 in, Strong Hold visible cart, countertop cabinets
Stainless Strong Hold stainless cart, Jamco YV-Series
Before you order

Tell us the heaviest drawer, the longest item, the narrowest doorway on the route, and whether the cart sees washdown. Confirm the full model number, casters, lock and keying on the quote.

About the author. Tom McGovern has worked in the industrial material handling industry since 1981, bringing over 45 years of hands-on experience helping businesses select the right equipment for their applications. His expertise includes specifying and quoting Rousseau R-Series and L-Series drawer carts, Strong Hold tool carts, Little Giant mobile cabinets and stainless carts.

Questions about this guide? Call 866-333-0728 to speak with an experienced material handling specialist.

Ready for a quote?

Send us these details and a material handling specialist will reply, typically within one business day.

  • Dimensions
    Size of the load and the space it goes in
  • Load
    Weight per item, shelf or level
  • Quantity
    How many units you need
  • Delivery ZIP code
    For freight pricing
  • Drawing
    A sketch, photo or spec sheet, if you have one
Get a Fast Quote Call 866-333-0728

Tell us the heaviest drawer and the narrowest doorway

Those two answers pick the line and the width. Then we build the drawer mix with you. Quotes are reviewed by material handling specialists, typically within one business day.

866-333-0728

Browse modular drawer carts and tool carts at custommhs.com

No bots. No guesswork. Real experts.

Sources

Rousseau, Strong Hold, Jamco and Little Giant figures as published on CustomMHS product listings and by the manufacturers.

Disclaimer. This guide is educational content and reflects the opinion and general experience of CustomMHS. Sizes, drawer ratings and caster ratings are published figures and can change. Confirm the full model number, casters and locks on the quote. Reviewed November 2026.