Industrial Equipment Experts Since 1980 | Mon–Fri, 7 AM–6 PM ET
No bots. Real experts. 866-333-0728
Get a Fast Quote
Get a Fast Quote

CustomMHS Buyer's Guide

WireCrafters Style 840

One partition system, two very different meshes. Woven wire is interlocked at every crossing. Welded wire is lighter and easier to cut openings in. Choosing between them is the first decision, and most of the specification follows from it.

Covers: Style 840 woven wire · RapidWire welded wire · panels, posts, doors and locks Questions: 866-333-0728 Written and reviewed by: Tom McGovern · November 2026
Section One

One system, two meshes

Getting the names straight, because they are used loosely.

Quick answers
  • Style 840 is the partition system: posts, panel frames, doors and hardware. It comes with two meshes.
  • Woven wire is 10 gauge in a 2 in by 1 in opening, heavy duty. RapidWire welded wire is 10 gauge in a 2 in by 2 in opening, medium duty.
  • Choose woven where someone has a reason to get through. Choose welded to separate areas and control traffic.
  • Stock heights are 8 ft 5-1/4 in, 10 ft 5-1/4 in and 12 ft 5-1/4 in. Panels are 1 ft to 10 ft wide. Posts go no more than 10 ft 2 in apart.
  • Two of the latch sets do not lock, ceiling panels are not load bearing, and anyone working inside needs an exit that needs no key.

Heavy duty

Style 840 woven wire

10 gauge wire in a 2 in by 1 in rectangular opening, interlocked at every crossing. The frame is 1-1/4 in by 1-1/4 in by 1/8 in hot-rolled angle, and panels longer than 3 ft 6 in have flat steel stiffeners welded behind the mesh. See Style 840 woven wire partitions.

Medium duty

RapidWire welded wire

10 gauge wire in a 2 in by 2 in square mesh, welded at each crossing. WireCrafters positions it as the quick ship, fast installation line. See RapidWire welded wire cages.

Confirm the mesh by its size, not its name

The RapidWire name is sometimes used loosely. On a quote, 2 in by 1 in is the woven heavy duty mesh and 2 in by 2 in is the welded medium duty mesh.

This is the product line guide: how to read the part numbers and specify a system. For reach distances, DEA rules and the wider category, see our wire partitions and security cages guide.

Please read this part

This guide is educational and reflects the opinion and general experience of CustomMHS as an equipment distributor. It is not a security, safety or code assessment. Sizes, weights and part numbers are WireCrafters' published figures. Confirm the current data sheet for your exact model before you order.

Section Two

Woven or welded

The first decision. Most of the rest follows from it.

Short answer: Woven resists cutting and reaching through. Welded is a quarter to a third lighter and holds its shape when you cut openings.

Published differences
Factor Woven, 2 in by 1 in Welded, 2 in by 2 in
Cutting Interlocked at every crossing. One cut strand does not open a hole Fused at each crossing. Cutting frees the cut wires
Reaching through The 1 in dimension is listed as stopping a hand The 2 in by 2 in opening admits a hand
Weight, 8 ft by 4 ft panel 53 lb 38 lb
Weight, 8 ft by 5 ft panel 63 lb 44 lb
Cutting openings Ask us Cutouts can be made and the mesh keeps its shape
Duty Heavy Medium
Typical use Theft prevention, controlled substances, high-value stock Separation and traffic control
Someone might cut in
Woven.
Someone might reach through
Woven.
Controlled substances
Woven. The DEA cage uses the 2 in by 1 in mesh.
Keeping traffic out of an area
Welded is enough.
Openings for conveyor or ductwork
Welded.
A large run where lifting panels is the hard part
Welded, for the lighter panels.

Do not assume welded is always the lower price or the shorter lead time. Ask for both on your layout and compare.

Section Three

Reading a model number

WireCrafters does not publish a key. This is our reading, checked against the listed dimensions.

Short answer: A cage number gives the mesh, footprint, height, number of walls and door type.

W 66 8 4 H
W
Mesh: W is woven Style 840, RW is RapidWire welded
66
Footprint: 6 ft 6 in by 6 ft 4 in
8
Height: the 8 ft 5-1/4 in system
4
Number of walls
H
Door: H is hinged, S is sliding

W581H is a woven one-wall cage 5 ft 6 in wide and 8 ft 5-1/4 in high with a hinged door. RW581H is the same cage in welded mesh. RW161484H is a welded four-wall cage on a 16 ft by 14 ft footprint. Use this to compare quotes, and confirm the dimensions on the listing.

Component part numbers
Component Scheme Example
Woven panels Width in feet, then height in feet 84 is 8 ft by 4 ft
Welded panels BACK, then width and height BACK84 is 8 ft by 4 ft
Posts RP run or CP corner, then system height in feet RP8, CP12
Hinged doors HD, width, opening height, system height HD-47-10
Double hinged doors DHD, same pattern DHD-67-8
Sliding doors SD, same pattern SD-58-8
Rack enclosures RE, then width, height and depth RE9836
Driver cages MT, walls, size, HD MT2-56HD

The same door may appear with or without hyphens, HD-37-8 or HD378. It is the same part.

Section Four

Panels and sizes

Stock sizes, weights, and the filler panel that saves the installation.

Short answer: Panels are 1 ft to 10 ft wide and 4 ft or 5 ft high, and stack to make the system height. Order the adjustable filler panel with the run.

Panels install between posts. Stock widths run from 1 ft to 10 ft in 1 ft steps, in 4 ft and 5 ft heights that stack to the system height.

Listed panel weights
Panel size Woven part Woven weight Welded part Welded weight
1 ft by 4 ft 14 13 lb BACK14 8 lb
2 ft by 4 ft 24 18 lb BACK24 12 lb
4 ft by 4 ft 44 31 lb BACK44 22 lb
6 ft by 4 ft 64 41 lb BACK64 30 lb
8 ft by 4 ft 84 53 lb BACK84 38 lb
10 ft by 4 ft 104 63 lb BACK104 45 lb
8 ft by 5 ft 85 63 lb BACK85 44 lb
10 ft by 5 ft 105 74 lb BACK105 54 lb

The adjustable filler panel

Buildings are not even multiples of one foot. The adjustable filler panel closes the gap at the end of a run. AP4 is for 4 ft high panels and AP5 for 5 ft. They are sheet metal and adjust from 1 in to 11 in.

Finish

The standard finish is gray enamel for interior use. In-stock colors are white, blue, safety yellow, orange, tan, red and black, and custom powder coat is available at added cost. If the partition will see weather, tell us at quote time.

Section Five

Posts, base plates and anchoring

The part that makes a partition a barrier.

Short answer: Posts are 2 in square tube on a welded base plate, anchored with 3/8 in wedge anchors, no more than 10 ft 2 in apart.

Listed post and anchoring details
Item Listed
Post 2 in by 2 in, 14 gauge square tubing
Base plate 1/4 in by 2 in by 7 in plate welded to the post
Maximum post spacing 10 ft 2 in on center
Floor anchors 3/8 in wedge anchors
Assembly hardware 3/8 in plated
Floor sweep on stock doors 3-1/4 in, or 1-3/4 in with a lower cover bar
Stock post heights 8 ft 5-1/4 in, 10 ft 5-1/4 in, 12 ft 5-1/4 in
Post part numbers RP8, RP10, RP12 run posts. CP8, CP10, CP12 corner posts
Hardware faces in

The 3/8 in hardware is specified so it cannot be reached from outside the enclosure. The cage has an inside and an outside, and it has to be assembled with the fasteners facing in. Assembled backward, anyone with a nut driver can take it apart.

The whole system bolts together. Nothing is welded on site. On DEA work, post spacing is no more than 10 ft, with horizontal reinforcement.

Section Six

Heights, ceilings and the gap at the top

Whether to close the top is a security decision.

Short answer: Pick the height from the threat. Add ceiling panels or go full height where someone could climb over. Ceiling panels are not load bearing.

Three stock heights are listed: 8 ft 5-1/4 in, 10 ft 5-1/4 in and 12 ft 5-1/4 in. Taller custom heights are available for runs to the roof deck. Ask us.

Worked example. An 8 ft 5-1/4 in partition in a building with 24 ft of clear height leaves 24 ft − 8 ft 5-1/4 in = 15 ft 6-3/4 in of open air above it. Anyone willing to climb a rack or a ladder is inside.

Staffed area, casual deterrence
8 ft 5-1/4 in is normally enough.
Racking or a mezzanine next to the partition
Go taller or add a ceiling. A rack beside a partition is a ladder.
High-value or controlled stock
Ceiling panels, or run to the structural deck.
Unstaffed overnight
A ceiling or full height.

Ceiling panels are an option. They are interchangeable with wall panels, attach with slotted angle, and are listed with clear spans up to 30 ft.

Ceiling panels are not load bearing

A wire ceiling keeps a person from climbing in. It is not a platform or a storage shelf, and nothing should hang from it.

Open mesh lets the building's lighting, ventilation and sprinklers keep working, which is an advantage over a drywall room. Sprinkler coverage over and inside an enclosure is still a question for your fire protection engineer, especially with ceiling panels.

Section Seven

Doors

The door type is usually decided by the clearance you do not have.

Short answer: Hinged doors need swing room. Sliding doors need a clear run of partition beside the opening at least as wide as the door.

Hinged doors are listed 3 ft or 4 ft wide with a 7 ft 3-1/4 in high opening, on two door posts with three hinges. They are universal: left or right hand and in or out swing are set at installation.

Single hinged doors as listed
Part Opening Overall height Weight
HD-37-8 3 ft by 7 ft 3-1/4 in 8 ft 5-1/4 in 106 lb
HD-47-8 4 ft by 7 ft 3-1/4 in 8 ft 5-1/4 in 118 lb
HD-37-10 3 ft by 7 ft 3-1/4 in 10 ft 5-1/4 in 123 lb
HD-47-10 4 ft by 7 ft 3-1/4 in 10 ft 5-1/4 in 139 lb
HD-37-12 3 ft by 7 ft 3-1/4 in 12 ft 5-1/4 in 138 lb
HD-47-12 4 ft by 7 ft 3-1/4 in 12 ft 5-1/4 in 157 lb

Double hinged doors give a 6 ft or 8 ft opening at the same height, from DHD-67-8 at 170 lb to DHD-87-12 at 251 lb. Use one where a pallet has to pass and a sliding door will not fit.

Sliding doors, 8 ft system, as listed
Part Opening width Weight
SD-38-8 3 ft 124 lb
SD-48-8 4 ft 137 lb
SD-58-8 5 ft 149 lb
SD-68-8 6 ft 196 lb
SD-88-8 8 ft 230 lb
SD-108-8 10 ft 279 lb

Worked example. A 6 ft sliding door needs 6 ft of opening plus at least 6 ft of clear partition beside it to slide onto. That is 12 ft of wall with nothing stacked against it.

  • Dutch doors: two leaves, with an 18 in deep shelf on the bottom leaf. The pass-through counter for a tool crib or driver cage.
  • Vertical rise and tunnel doors: made to order for conveyor and vehicle openings.
  • Self-closing: a door closer is an option. If your application requires self-closing, self-locking doors, put it in writing on the order.
Section Eight

Locks, latches and exit devices

The lock is a separate line from the door.

Short answer: SF2-SB1 and SF3-SB3 latch but do not lock. Where a door locks and people work inside, add an exit device.

Listed locking options
Part Description Fits
SF-1 / SB-1 Key lock outside, recessed thumb turn inside Hinged
SDLKXKD Key lock and thumb turn for a sliding door Sliding
SF2-SB1 Thumb turn latch. Latches only, does not lock Hinged or sliding
SF3-SB3 Door knob entry. Latches only, does not lock Hinged
SF1-SB4 Key lock with lever handle inside. Listed as meeting ADA requirements Hinged
CF1-CB1 ADA handle set Hinged
CE-2 Ten-digit keypad for an electric strike or magnetic lock, up to 64 codes Either
CF-2 Five-button coded lock Hinged
CE-3 Magnetic lock Sliding
Card reader Works an electric strike or magnetic lock, with ten cards Either

Exit devices: CB-2 is a push paddle, CB-3 is a push bar across the full width of the door, and CD-4 is a push bar with a battery-powered alarm. See WireCrafters locks.

People inside need a way out

If anyone works inside the enclosure, they have to be able to leave without a key. That is a building code matter, so confirm it with your building official. On a multi-cage project, price the locking hardware early. It can be a large part of the job.

Section Nine

One, two, three and four wall cages

Buy only the walls you do not already have.

Short answer: Count the solid, full-height building walls you can use. Everything else is partition.

Wall configurations
Cage Where it goes
1 wall Between two existing walls, closing an alcove
2 wall In a building corner
3 wall Against one building wall. The most common
4 wall Free standing on open floor, with or without a ceiling
Check what the existing wall is

A stud and drywall wall is not as secure as the partition, and neither is a wall that stops at a drop ceiling with open space above. Walk the perimeter before you decide how many walls to buy.

Listed applications include tool cribs, server cages, evidence enclosures, driver cages and DEA drug storage. Tenant storage lockers are a related line covered in our lockers guide.

Section Ten

Rack enclosures and rack backing

Two products that bolt to pallet rack and solve two different problems.

Short answer: Rack backing keeps product from falling into the aisle behind. A rack enclosure turns bays into locked storage.

Rack backing

Rack safety backing uses the welded BACK panels, up to 12 ft wide and 4 ft or 5 ft high, mounted to the back of the rack. It is a falling-object control.

Rack enclosures

Pallet rack enclosures, the RE series, add wire sides, backs and doors to rack bays for secured storage. Part numbers give width, height and depth.

Neither changes the capacity or condition of the rack. Our pallet racking guide covers rack inspection.

Section Eleven

DEA cages

Where the federal rule sets the specification.

Short answer: For Schedule III to V storage, use the woven 2 in by 1 in mesh, posts no more than 10 ft apart, horizontal bars every 5 ft, a ceiling, and self-closing, self-locking doors.

21 CFR 1301.72(b) sets the construction of a controlled substance cage: steel fabric of at least No. 10 gauge, mesh openings no larger than 2-1/2 in, posts no more than 10 ft apart, horizontal reinforcements every 60 in, a mesh ceiling or walls attached to the structural ceiling, and an alarm. The WireCrafters DEA cage is built to those numbers with the woven mesh. Schedule I and II substances need a safe or vault.

Our wire partitions guide sets out the rule in a table. Confirm your requirements with the DEA and your compliance counsel before you order.

Section Twelve

Machine guarding

Use the product made for it.

Short answer: A security partition is not automatically a machine guard. Guard fencing is laid out from the hazard, the mesh opening and a risk assessment.

Around a machine or robot, the fence has to keep a person from reaching the hazard. That depends on the mesh opening and the distance, under ISO 13857, and the gate normally needs an interlock tied to the machine. WireCrafters makes machine guard fencing and lift-out RapidGuard fencing for that job.

Our barriers and machine guarding guide and wire partitions guide cover reach distances. Have the layout confirmed by your safety engineer.

Section Thirteen

Laying out a run

A planning example. We do the final layout from your sketch.

Short answer: Add the panel widths and 2 in for each post, compare to the wall, and close the remainder with a filler panel.

A single wall closing an alcove that measures 23 ft 7 in, which is 283 in, with no door:

Planning a 23 ft 7 in run
Step Math Result
Panels 10 ft + 10 ft + 2 ft 22 ft, or 264 in
Posts 4 posts × 2 in 8 in
Panels and posts 264 in + 8 in 272 in
Left over 283 in − 272 in 11 in
Close the gap Adjustable filler, 1 in to 11 in One filler panel stack

For the 8 ft 5-1/4 in system that run is two rows of 4 ft high panels, so six panels and two AP4 fillers. Send us the wall dimensions, the door locations and anything that crosses the line, such as pipes, conduit or a conveyor.

Section Fourteen

Common and costly mistakes

Most show up on installation day.

Short answer: Order the filler, face the hardware in, check the parking wall for a sliding door, and do not buy a latch as a lock.

Choosing by the line name

Confirm 2 in by 1 in woven or 2 in by 2 in welded.

Forgetting the filler panel

A partition that stops 7 in short of a wall is not secure.

Assembling with the hardware facing out

The fasteners belong inside.

Posts more than 10 ft 2 in apart

That is outside the listed maximum.

Stopping at 8 ft beside a rack

A rack is a ladder.

Storing on the ceiling panels

They are not load bearing.

A sliding door with no room to slide

It needs clear partition beside the opening.

A latch where a lock was needed

SF2-SB1 and SF3-SB3 do not lock.

No exit device

People inside need to get out without a key.

A security partition as a machine guard

Use guard fencing laid out from a risk assessment.

Section Fifteen

Frequently asked questions

What buyers ask when specifying Style 840.

What is WireCrafters Style 840?

It is a wire partition system of posts, framed panels, doors and hardware. It comes with woven wire in a 2 in by 1 in mesh or RapidWire welded wire in a 2 in by 2 in mesh, both 10 gauge.

What is the difference between Style 840 woven wire and RapidWire?

Woven wire is interlocked at every crossing in a 2 in by 1 in opening and is the heavy duty choice for security. RapidWire is welded in a 2 in by 2 in opening, is lighter, and suits separation and traffic control.

How do I read a WireCrafters cage model number?

W or RW is the mesh, the next digits are the footprint, then the height class, the number of walls and the door type. W664H reads as woven, 6 ft 6 in by 6 ft 4 in, four walls, hinged door, with the height digit between.

What heights does Style 840 come in?

Stock system heights are 8 ft 5-1/4 in, 10 ft 5-1/4 in and 12 ft 5-1/4 in. Taller custom heights are available.

What panel sizes are stocked?

Widths from 1 ft to 10 ft in 1 ft steps, in 4 ft and 5 ft heights that stack to the system height.

How far apart can the posts be?

The listed maximum is 10 ft 2 in on center. On DEA cages it is no more than 10 ft.

How much does a panel weigh?

An 8 ft by 4 ft woven panel is listed at 53 lb and the welded panel at 38 lb.

Can I put anything on the ceiling panels?

No. Ceiling panels are not load bearing. They close the top of the cage against climbing.

Hinged or sliding door?

A hinged door needs swing room. A sliding door needs a clear run of partition beside the opening at least as wide as the door.

Do the latch sets lock?

SF2-SB1 and SF3-SB3 are listed as latches only. For a locking door choose a key lock, keypad, coded lock or card reader, and add an exit device if people work inside.

Is Style 840 used for DEA cages?

Yes. The WireCrafters DEA cage uses the woven 2 in by 1 in mesh with posts no more than 10 ft apart, horizontal bars every 5 ft, a ceiling, and self-closing, self-locking doors.

Section Sixteen

Quick-reference tables

The system on one screen.

Style 840 at a glance
Item Listed
Woven mesh 10 gauge, 2 in by 1 in
Welded mesh 10 gauge, 2 in by 2 in
Panel widths 1 ft to 10 ft
Panel heights 4 ft and 5 ft
System heights 8 ft 5-1/4 in, 10 ft 5-1/4 in, 12 ft 5-1/4 in
Posts 2 in by 2 in, 14 gauge, 10 ft 2 in maximum spacing
Anchors and hardware 3/8 in
Filler panel Adjusts 1 in to 11 in
Hinged door opening 3 ft or 4 ft by 7 ft 3-1/4 in
Ceiling clear span Up to 30 ft
What we list
Product Listing
Woven and welded partitions Woven wire, RapidWire welded
Cages DEA cages, server cages, driver cages
Racking Rack enclosures, rack backing
Guarding Machine guard fencing, lift-out fencing
Hardware Locks
Before you order

Send a sketch with dimensions, door locations and swings, ceiling height, what the building walls are made of, and who needs access.

About the author. Tom McGovern has worked in the industrial material handling industry since 1981, bringing over 45 years of hands-on experience helping businesses select the right equipment for their applications. His expertise includes specifying and quoting WireCrafters Style 840 woven wire, RapidWire welded wire, DEA cages and rack enclosures.

Questions about this guide? Call 866-333-0728 to speak with an experienced material handling specialist.

Ready for a quote?

Send us these details and a material handling specialist will reply, typically within one business day.

  • Dimensions
    Size of the load and the space it goes in
  • Load
    Weight per item, shelf or level
  • Quantity
    How many units you need
  • Delivery ZIP code
    For freight pricing
  • Drawing
    A sketch, photo or spec sheet, if you have one
Get a Fast Quote Call 866-333-0728

Send us the sketch and we will build the parts list

Wall lengths, height, doors and locks. We will lay out panels, posts and fillers. Quotes are reviewed by material handling specialists, typically within one business day.

866-333-0728

Browse WireCrafters at custommhs.com

No bots. No guesswork. Real experts.

Sources

21 CFR 1301.72 · ISO 13857 · WireCrafters published catalog data and figures on CustomMHS product listings.

Disclaimer. This guide is educational content and reflects the opinion and general experience of CustomMHS. It is not a security, safety or code assessment. Sizes, weights and part numbers are published data and can change. Confirm the layout, the hardware and any code requirements before ordering. Reviewed November 2026.