Section One
Four machines, one decision
This category looks sprawling. Underneath, almost every stacker is one of four combinations.
Quick answers
- Capacity is rated at a load center, usually 24 in. A 3,000 lb stacker lifting a 72 in deep load is good for about 2,000 lb.
- Powered lift with manual push is the best value for most buyers. The injuries come from the lifting, not the pushing.
- If straddle legs fit around your load, buy straddle. Use counterbalance only when legs cannot go under or around the load.
- A battery-powered stacker or pallet truck is a powered industrial truck under OSHA 1910.178, and operator training applies.
Two jobs can each be manual or powered: lifting the load, and moving the machine across the floor.
Manual lift, manual push
The simple one
Lowest cost, lightest, nothing to charge. Right for occasional lifting of lighter loads. See Logitrans mini manual stackers.
Powered lift, manual push
The best value
The lifting effort goes away while the machine stays light and affordable. If you lift often and do not travel far, this is usually the answer. See battery-powered lift stackers.
Powered lift, powered drive
For distance
The operator steers and the machine does the rest. Justified by distance and frequency, not weight. See the Logitrans Logiflex Self Mini-1000, listed with 36 in to 65 in of lift.
Self-leveling
No operator input
A cart that keeps the top of the load at working height as material is removed. Often the right answer when the real problem is bending. See self-leveling carts.
Choose by counting cycles, not weight
The weight of the load tells you the capacity class. How many times a shift someone lifts, and how far they travel, tells you which machine.
- A few lifts a day, short distances: manual lift and push.
- Many lifts a day, short distances: powered lift, manual push.
- Many lifts a day, long distances or ramps: fully powered.
- Nobody lifts, but everybody bends: a self-leveling cart or a lift table.
The cheapest upgrade is powered lift
Pushing a wheeled machine on a smooth floor is not what hurts people. Pumping a hydraulic handle forty times a shift is. If the budget is tight, buy the powered lift and keep pushing.
Please read this part
This guide is educational and reflects the opinion and general experience of CustomMHS as an equipment distributor. It is not a compliance assessment or legal advice. Powered industrial truck operation is governed by OSHA 1910.178 in full. Capacities and lift heights are the manufacturers' published figures. Confirm the current data sheet for your exact model before you order.
Section Two
Load center: the spec that cuts your capacity
A machine rated 3,000 lb will not safely lift 3,000 lb if the load sticks out too far.
Short answer: Load center is half the load depth for an evenly packed load. If yours is more than the rated 24 in, multiply the rating by 24 and divide by your load center.
Capacity is always stated at a load center: the distance from the face of the forks to the center of gravity of the load. The usual reference is 24 in, which is the middle of a standard 48 in deep pallet. Move the center of gravity further out and capacity drops, because the load has a longer lever against the machine.
Worked example: a 3,000 lb stacker rated at a 24 in load center
| Load depth |
Load center |
Math |
Approximate capacity |
| 48 in |
24 in |
3,000 × (24 ÷ 24) |
3,000 lb |
| 60 in |
30 in |
3,000 × (24 ÷ 30) |
2,400 lb, a 20% loss |
| 72 in |
36 in |
3,000 × (24 ÷ 36) |
2,000 lb, a one-third loss |
Nothing about the machine announces this. The plate says 3,000 lb, the load looks like it fits, and the stacker will try the lift. What changes is stability, and the failure is the machine tipping forward. The formula is a planning estimate. The manufacturer's capacity chart for the exact model is the authority.
Where load center catches people
- Deep loads: anything past 48 in deep.
- Loads that overhang the forks: long stock and awkward crates.
- Unevenly packed pallets: the heavy end may be the far end.
- Attachments: a rotator, tilter or box holder adds weight ahead of the fork face before you load anything. The same problem is covered for forklifts in our hoppers guide.
Ask for capacity at your load center
When you ask for a quote, give the load depth and how it is packed. That lets us quote the capacity that applies to your work, not the number on the brochure.
Section Three
Straddle, fork-over or counterbalance
Base design decides what you can pick up and how much room you need.
Short answer: Straddle is the most stable. Fork-over is narrower and needs an open-bottom pallet or skid. Counterbalance picks up anything from anywhere, at a lower capacity.
Narrowest with legs
Fork-over
The legs run under the load with the forks above them. Works with open-bottom pallets and skids that give the legs somewhere to go.
Choosing the base
| Situation |
Straddle |
Fork-over |
Counterbalance |
| Standard open-bottom pallets |
Yes |
Yes |
Yes |
| Closed-bottom or solid-base loads |
Yes |
No |
Yes |
| Load against a wall or another load |
No |
No |
Yes |
| Picking up from a bench or table |
Limited |
Limited |
Yes |
| Capacity for the money |
Best |
Good |
Lowest |
The practical rule: if straddle legs fit around your load, buy straddle. Reach for counterbalance when legs will not work, and accept the lower rating. For a straddle unit, measure the outside width of your widest pallet or load and confirm it fits between the legs.
Section Four
Lift height and capacity at height
The second place a headline capacity can mislead you.
Short answer: Measure the highest point you place loads, add a few inches of clearance, and ask for the capacity at that height. Then check the lowered mast height against your doorways.
On many machines the rated capacity does not hold through the whole lift range. Raising the load raises the combined center of gravity, so a stacker may be derated near the top of the mast.
The lines we carry show how wide the range gets. The Logiflex Self Mini-1000 is listed with 36 in to 65 in of lift, the Self Maxi-1003 with 36 in to 130 in, and the Self-Maxi-1203 with up to 63 in. The tallest machine and the strongest machine are usually not the same one.
Worked example: how much lift do you need?
Placing pallets on a shelf beam 96 in above the floor
| Step |
Math |
Result |
| Top of the beam |
|
96 in (8 ft) |
| Clearance to lift over the beam |
96 in + 6 in |
102 in |
| Lift height to ask for |
|
At least 102 in |
A 65 in machine cannot do that job. A 130 in machine can, and you should ask for its capacity at 102 in, not at floor level.
Two questions before you order
What is the capacity at my working height? Does the mast, lowered, fit under my lowest doorway, beam or sprinkler? A machine that reaches 130 in has a tall mast when it travels.
Section Five
The training obligation
The part of this purchase that is not in the equipment price.
Short answer: OSHA 1910.178 covers industrial trucks powered by electric motors, including walk-behind units. Plan on operator training, evaluation, and a re-evaluation at least every three years for any battery-powered unit.
Buyers reason that a compact stacker is not a forklift, so forklift rules do not apply. The scope of 29 CFR 1910.178 is wider than that. It covers fork trucks, tractors, platform lift trucks, motorized hand trucks and other specialized industrial trucks powered by electric motors or internal combustion engines.
A battery-powered walk-behind stacker or pallet truck is a motorized hand truck. The test in the scope is whether the truck is powered by an electric motor, not whether the operator rides, so the operator training rule applies.
What 1910.178(l) requires
| Paragraph |
Requirement |
| (l)(1)(i) |
The employer ensures each operator is competent, shown by completing the training and evaluation in the rule |
| (l)(1)(ii) |
Training is completed before the employee operates the truck, except during training itself |
| (l)(4) |
Refresher training when needed, and an evaluation of each operator at least once every three years |
So the real cost of a fully powered unit includes training, evaluation, records and the three-year re-evaluation. That is normal and manageable. It should be part of the decision, not a surprise afterward.
Powered lift with manual push
A unit that is pushed by hand but lifts on battery power still has an electric motor. Treat it as a powered industrial truck and train the operators. If you believe a specific unit falls outside the rule, have your safety staff or your OSHA area office confirm that before you rely on it.
Where this changes the decision
If one person lifts now and then, a fully manual stacker may be the better overall answer. If you already run forklifts and have a training program, adding powered stackers to it costs very little.
Section Six
Pallet trucks and skid lifts
Moving loads across the floor, and raising skids to working height.
Short answer: Use a pallet truck for pallets and a skid lift for flat-bottom skids. Check what your loads sit on before you order.
Pallet trucks
A pallet truck lifts a pallet just clear of the floor and moves it. Variants we list:
Skid lifts
A skid lift is a pallet truck that keeps going up. It raises a skid or open-bottom pallet to a comfortable working height so nobody bends to load or unload it. We list manual skid lifts, battery-powered skid lifts and stainless steel skid lifts.
Check what your loads sit on
A pallet with bottom boards, an open-bottom skid, or a solid base. It decides which machine can get under the load. Forks that roll on the floor cannot enter a pallet with bottom boards in the way, and straddle legs are the usual answer for those.
Section Seven
Lift carts and post lifts
Not for stacking. For putting work at the right height so people stop bending.
Short answer: Watch where people bend. A scissor lift cart or a self-leveling cart fixes a height problem better than any stacker.
Scissor lift carts
A wheeled cart with a scissor mechanism that raises the deck. Manual versions are pumped by foot. Battery versions take the effort out of frequent height changes. The use is a work cell or packing station where material has to be at working height and then moved.
Self-leveling carts
A self-leveling cart keeps the top of the load at a steady working height. As material comes off and the load gets lighter, the deck rises. It needs no operator action, so it cannot be forgotten or bypassed.
Linear actuated lift carts
The Lift Products linear actuated lift cart uses an electric actuator for smooth, precise height adjustment. Worth it where the exact height matters, such as feeding a machine or lining up with a conveyor.
Post lift tables
An adjustable post lift table gives compact vertical positioning at a workstation and takes less floor than a scissor mechanism. For stationary scissor tables see our lift tables guide.
Section Eight
Rotators, reel handling and tilters
Where the job is changing which way a load faces, not how high it is.
Short answer: Choose a rotator to empty boxes, a reel rotator for wire and cable, and a tilter to present the contents of a container at an angle.
Box and crate rotators
A rotator lifts a box or crate, holds it, and rotates it so the contents can be poured out or reached. Two choices define it:
- Adjustable or fixed box holder. An adjustable holder takes boxes of different widths. A fixed holder suits one standard box and is simpler.
- How much is powered. From powered lift with manual push and rotation, up to powered lift, drive, rotation and clamping. Match it to cycle count.
Both fork-over and straddle-leg bases are listed, so the base decision in section three still applies.
Reel rotators and lifters
Reels of wire, cable and hose are heavy and awkward, and they roll. Reel handling equipment lifts, clamps and rotates them under control. We list the Logitrans RL-500 reel lifter and reel rotators from fully manual to fully powered. Our reel lifts and rotators guide covers them in detail.
Container tilters
A tilter tips a container so its contents face the worker. The Logitrans Logitilt is listed at 2,200 lb, with a straddle-leg version and a stainless steel version.
Section Nine
Batteries
The part of a powered machine that decides whether it is ready when someone needs it.
Short answer: Lead-acid suits one shift with overnight charging. Lithium suits several shifts and charging in short breaks.
Battery comparison
|
Lead-acid |
Lithium |
| Purchase cost |
Lower |
Higher |
| Charging |
Long, full charges |
Fast, and tolerates top-up charging between tasks |
| Maintenance |
Watering and terminal cleaning on flooded types |
Very little |
| Swapping |
Heavy |
Fast-swap designs on some units |
| Best for |
One shift with overnight charging |
Several shifts, or where downtime is costly |
The Logitrans lithium pallet truck is listed with a fast-swap battery, which is what lets one machine cover more than one shift.
Charging is a facilities question
Before you buy, settle where the unit charges and whether the outlet and circuit are right for the charger. A machine parked far from its charger is a machine people stop using.
Section Ten
Stainless and washdown
Painted steel does not last in food, pharmaceutical or washdown areas.
Short answer: Stainless versions are listed for stackers, skid lifts, pallet trucks and tilters. Check the mechanism and the wheels, not just the frame.
We list stainless versions across the category: the Logitrans HSI manual stacker, the EHSI-1000 powered stacker, stainless skid lifts, stainless pallet trucks and the stainless Logitilt.
What to check beyond the frame:
- Are the hydraulics and bearings protected, or only the body?
- What are your cleaning chemicals? Our cleanroom and stainless guide covers stainless grades.
- How is the battery and charger arranged for a wet area?
- Are the wheels suited to wet floors?
Section Eleven
Choosing by application
Find the row that matches your situation.
Short answer: Count the cycles, measure the load depth, and look at what the load sits on.
Occasional lifting, lighter loads
A manual lift, manual push stacker. Nothing to charge.
Frequent lifting, short travel
Powered lift, manual push.
Frequent lifting and long travel, or ramps
Fully powered. Budget for operator training under 1910.178(l).
Loads deeper than 48 in
Run the load center math before choosing capacity. A 72 in deep load costs about a third of the rating.
Loads against a wall or on a bench
Counterbalance. Accept the lower capacity.
Pallets with bottom boards
Straddle legs, sized to fit around the pallet.
Raising skids to working height
A skid lift.
Moving pallets long distances all day
A fully powered pallet truck. Add a scale version if you weigh loads anyway.
People bend into emptying pallets
A self-leveling cart.
Feeding a machine or matching a conveyor
A linear actuated lift cart, or a post lift table at a fixed station.
Emptying boxes or crates
A box rotator. Adjustable holder if box sizes vary.
Wire, cable or hose reels
A reel lifter or rotator.
Food, pharmaceutical or washdown
Stainless versions of the stacker, skid lift, pallet truck or tilter.
More than one shift
A lithium battery with fast swap.
Section Twelve
Common and costly mistakes
The first two show up as accidents. The rest show up as regret.
Short answer: Check capacity at your load center and your working height, and count training into the cost of a powered unit.
Taking the headline capacity at face value
It applies at the rated load center, usually 24 in. A deeper load cuts it.
Not knowing about the training rule
OSHA 1910.178 covers motorized hand trucks powered by electric motors, and 1910.178(l) requires training and a three-year re-evaluation.
Confusing maximum lift with maximum capacity
Ask for the capacity at your working height.
Buying powered drive when powered lift was the need
Powered lift with manual push is usually the better value.
Choosing counterbalance without needing it
It costs capacity. If straddle legs fit, buy straddle.
Not checking the pallet bottom
Fork-over legs need an open bottom.
Ignoring the lowered mast height
Check doorways, beams and sprinklers.
Forgetting the attachment
A rotator or tilter moves the load center out before you load anything.
Buying more lift height than the job needs
It adds cost, mast weight and clearance problems.
Section Thirteen
Frequently asked questions
What comes up most often on quote calls.
What is load center and why does it matter?
Load center is the distance from the face of the forks to the center of gravity of the load. Capacity is rated at a stated load center, usually 24 in. If your load center is longer, the machine can safely lift less.
How do I work out my load center?
For an evenly packed load, divide the load depth by two. A 48 in deep pallet has a 24 in load center, and a 72 in deep load has a 36 in load center. For uneven loads, estimate toward the heavy end.
Do my operators need training for a small powered stacker?
Yes, plan on it. OSHA 1910.178 covers motorized hand trucks powered by electric motors, and 1910.178(l) requires operator training and evaluation before use, with a re-evaluation at least every three years. A fully manual stacker is outside that rule.
Straddle legs, fork-over or counterbalance?
Straddle is the most stable and works with pallets that have bottom boards, as long as the legs fit around the load. Fork-over needs an open-bottom pallet or skid. Counterbalance needs no legs and picks up from walls and benches, at a lower capacity.
Is the rated capacity the same at full lift height?
Often not. Many machines are derated near the top of the mast. Ask for the capacity at your working height and check the manufacturer's capacity chart.
Powered lift or fully powered?
Powered lift with manual push suits frequent lifting over short distances. Fully powered suits long travel, ramps and constant use.
What is a self-leveling cart for?
It keeps the top of the load at working height. As material is removed and the load gets lighter, the deck rises, so nobody bends into the bottom of a pallet.
What is a skid lift?
It is a pallet truck that raises a skid or open-bottom pallet up to working height, so it can be loaded or unloaded without bending.
Lead-acid or lithium?
Lead-acid costs less and suits one shift with overnight charging. Lithium charges fast, tolerates top-up charging, needs little maintenance and suits several shifts.
Adjustable or fixed box holder on a rotator?
Choose adjustable if your box widths vary. Choose fixed if you run one standard box size.
What should I check on stainless lift equipment?
Check that the hydraulics and bearings are protected, that the stainless grade suits your cleaning chemicals, how the battery and charger are arranged for a wet area, and that the wheels suit wet floors.
Section Fourteen
Quick-reference tables
Published figures and citations used in this guide.
Key calculations and requirements
| Item |
Figure |
Source |
| Usual rated load center |
24 in |
Confirm on the data plate |
| Load center of an even load |
Load depth ÷ 2 |
Industry practice |
| Capacity estimate |
Rated capacity × (rated load center ÷ actual load center) |
Industry practice |
| Scope of powered industrial trucks |
Includes motorized hand trucks powered by electric motors |
OSHA 1910.178(a)(1) |
| Operator training |
Completed before operating, except during training |
OSHA 1910.178(l)(1) |
| Re-evaluation |
At least once every three years |
OSHA 1910.178(l)(4) |
Before you order
The load center formula is a planning estimate. Confirm the rated load center and capacity chart for the exact machine. Tell us the load weight, depth and packing, the working height and the cycles per shift, and we will specify it.
About the author. Tom McGovern has worked in the industrial material handling industry since 1981, bringing over 45 years of hands-on experience helping businesses select the right equipment for their applications. His expertise includes specifying and quoting stackers, pallet trucks, skid lifts, lift carts and rotators.
Questions about this guide? Call 866-333-0728 to speak with an experienced material handling specialist.