Industrial Equipment Experts Since 1980 | Mon–Fri, 7 AM–6 PM ET
No bots. Real experts. 866-333-0728
Get a Fast Quote
Get a Fast Quote

CustomMHS Buyer's Guide

Roll-Out Die Racks & Pull-Out Shelving

A roll-out die rack brings a 2,000 lb die out from under the shelf above it, so a crane or fork truck can lift it clear. Choose it by the size and weight of your biggest die, the space in front of the rack, and how you load it. The rest is shelf count.

Covers: MECO Roll-Out Shelf Racks · Jarke E-Z Glide roll-out shelving Questions: 866-333-0728 Written and reviewed by: Tom McGovern · November 2026
Section One

What a roll-out die rack is for

Getting a heavy die out from under the shelf above it.

Quick answers
  • MECO and Jarke roll-out racks are rated at 2,000 lb per shelf with 100% extension. MECO also rates the top of the unit at 2,000 lb.
  • A MECO model number gives the size. RSR447-4A is a 48 in wide, 48 in deep, 85 in tall add-on with four shelves.
  • A row is one starter plus add-ons. Three bays is one starter and two add-ons.
  • Bolt every rack to the floor before you load or extend a shelf, and open one shelf at a time.
  • A fully loaded four-shelf MECO rack can pass 11,000 lb. Check the floor.

A die on a fixed shelf has a problem: the shelf above it. A crane hook cannot come straight down to it, and a fork truck has to reach into the bay. People end up dragging, prying or rigging at an angle, which is how dies get dropped and people get hurt.

A roll-out shelf pulls the whole shelf out of the rack. MECO lists 100% shelf extension, so the shelf comes clear of the frame. Then a crane lifts straight up, or a fork truck lifts from the front, with nothing overhead.

Buy a roll-out rack

Heavy tooling, pulled often

Dies, molds and fixtures up to 2,000 lb that fit a 36 in or 48 in shelf.

Buy fixed shelving

Rarely touched, or light

Tooling that moves once a year does not need roll-out shelves. See our shelving guide.

Buy engineered racking

Bigger than the shelf

Dies over 2,000 lb or larger than 48 in by 48 in. See our pallet racking guide.

Please read this part

This guide is educational and reflects the opinion and general experience of CustomMHS as an equipment distributor. It is not a structural or floor loading assessment. Rigging, crane and fork truck work follow your plant procedures and the OSHA rules for that equipment. Ratings and weights are the manufacturers' published figures. Confirm the current data sheet for your exact model before you order.

Section Two

MECO and Jarke at a glance

The same rating and shelf sizes on our listings. Different construction details.

Short answer: Both are 2,000 lb per shelf with full extension. MECO lists a structural channel frame, locking shelves, a rated top and a fourth shelf size.

Listed specifications
Specification MECO Roll-Out Shelf Rack Jarke E-Z Glide
Shelf capacity 2,000 lb per shelf 2,000 lb per shelf, stated as holding at full extension
Top of unit Up to 2,000 lb See listing
Extension 100% 100%
Locking Shelves lock in the extended position See listing
Frame Structural 3 in channel Welded and bolted
Shelves 10 gauge steel Steel
Shelf adjustment 2 in vertical 2 in centers
Pull force See listing As little as 15 lb
Shelf sizes, width by depth 36 by 36, 36 by 48, 48 by 36, 48 by 48 in 36 by 36, 48 by 36, 48 by 48 in
Heights 62 in, 72 in, 85 in 62-1/2 in, 72-1/2 in, 84-1/2 in
Shelves per unit 3 at 62 in and 72 in, 4 at 85 in 3 or 4
Shipping Knocked down. Assembled units also offered Knocked down

We lead with MECO because it lists the details that matter when 2,000 lb sits on an extended shelf: the structural channel frame, 10 gauge shelves, and shelves that lock when extended. It rates the top of the unit, lists a 36 in wide by 48 in deep shelf for long, narrow tooling, and offers factory-assembled units. The Jarke E-Z Glide is a sound alternative with the same rating and a listed pull force of about 15 lb.

Section Three

Reading a MECO model number

Three digits give you the footprint and height.

Short answer: After RSR: shelf width, shelf depth, height, then the number of shelves, and A for an add-on.

RSR447-4A
RSR
MECO Roll-Out Shelf Rack
4, 4
Shelf width, then shelf depth. 3 is 36 in, 4 is 48 in
7
Height. 5 is 62 in, 6 is 72 in, 7 is 85 in
-4
Number of shelves
A
Add-on unit. No A means a starter

RSR447-4A is a 48 in wide, 48 in deep, 85 in tall add-on with four roll-out shelves. RSR335-3 is a 36 in by 36 in, 62 in tall starter with three.

MECO starter units, as published by MECO
Model Shelf, width by depth Height Shelves Weight
RSR335-3 36 in by 36 in 62 in 3 921 lb
RSR345-3 36 in by 48 in 62 in 3 1,100 lb
RSR435-3 48 in by 36 in 62 in 3 1,038 lb
RSR445-3 48 in by 48 in 62 in 3 1,220 lb
RSR336-3 36 in by 36 in 72 in 3 937 lb
RSR346-3 36 in by 48 in 72 in 3 1,119 lb
RSR436-3 48 in by 36 in 72 in 3 1,057 lb
RSR446-3 48 in by 48 in 72 in 3 1,237 lb
RSR337-4 36 in by 36 in 85 in 4 1,191 lb
RSR347-4 36 in by 48 in 85 in 4 1,414 lb
RSR437-4 48 in by 36 in 85 in 4 1,340 lb
RSR447-4 48 in by 48 in 85 in 4 1,570 lb

Every starter has a matching add-on with an A. MECO notes that the overall width of a starter is the shelf width plus 8 in, so a 48 in shelf makes a 56 in wide rack. Jarke uses EZ, then shelf width, depth and height in inches, with A for an add-on: EZ484872 is a 48 in by 48 in shelf in a 72-1/2 in starter.

Section Four

What 2,000 lb per shelf means

The rating is per shelf, for a load sitting flat on that shelf.

Short answer: Weigh the complete die as it will sit on the shelf, set it near the center, and do not exceed 2,000 lb.

Weigh the whole die

Use the weight of the complete die set: upper and lower shoes, guide posts, parallels or blocks under it, and any skid. A weight stamped on a die years ago may not match it today. If a die is near 2,000 lb, weigh it.

Keep the load centered

A small, heavy die at one corner of a 48 in by 48 in shelf loads one side of the slides. Set dies near the center on blocks or a skid that spread the load.

The top of a MECO rack

MECO states the top of the unit holds up to 2,000 lb. It does not roll out, so it suits tooling lifted by crane from above. Count it when you plan capacity and when you check the floor.

Over 2,000 lb is a different product

Do not share a die between two shelves, stack dies, or put a heavier die on top of the rack. A die over 2,000 lb belongs on racking engineered for it.

Section Five

Choosing shelf width and depth

The die footprint sets the minimum. How you load it sets the rest.

Short answer: Measure the largest die in both directions, including anything that sticks out, add room for forks or chains, and pick the smallest shelf that clears it.

MECO lists four shelf sizes, width by depth: 36 by 36, 36 by 48, 48 by 36 and 48 by 48 in. Width is across the face of the rack. Depth is into the rack.

Worked example

A die 30 in wide and 38 in front to back
Step Math Result
Width, with 2 in of clearance each side 30 + 2 + 2 34 in. A 36 in wide shelf works
Depth, with 2 in of clearance front and back 38 + 2 + 2 42 in. Needs a 48 in deep shelf
Shelf to order Smallest size that clears both 36 in by 48 in, a MECO size

The 2 in clearance is an example. Use what your forks, chains or slings need. Nothing may overhang a roll-out shelf, because overhanging tooling catches the frame when the shelf slides back in. If you load by fork truck from the front, check that the forks are long enough to reach under a die on a 48 in deep shelf.

Section Six

Choosing height and shelf count

More shelves only help if each die still fits its opening.

Short answer: The 62 in and 72 in racks have three shelves and the 85 in rack has four. Check your tallest die against the opening.

MECO heights
Height Shelves Notes
62 in 3 The lowest top level, easiest to see onto. Good where hook height is limited
72 in 3 The same three shelves with more vertical room for taller dies
85 in 4 The most storage per floor space, with shorter openings

The frame adjusts in 2 in steps, so each opening can be set to its die. Set the opening to the die shut height, plus any blocks or skid, plus room to lift. For a fork truck lift, add room to raise the forks without striking the shelf above. MECO also lists additional shelves.

At 85 in, the top of the unit is higher than most fork truck operators can see onto, and it does not roll out. If you use it, load it by crane.

Section Seven

Starter and add-on units

Build a row with one starter and as many add-ons as you need.

Short answer: A starter stands alone. An add-on shares an upright with the unit beside it.

Starter and add-on, as published by MECO
Starter RSR447-4 Add-on RSR447-4A
Stands alone Yes No. Attaches to a starter or another add-on
Width Shelf width + 8 in, so 56 in Adds 4 in to the overall width when joined to a starter, per MECO
Weight 1,570 lb 1,474 lb

Worked example. A row of three bays is 1 starter + 2 add-ons, not three starters. An add-on must be the same height and shelf depth as the unit it joins. Have us confirm the finished row length on the quote before you lay out the wall, and leave wall space at the end of the row if you expect more dies.

Section Eight

Loading and unloading

Extend, lock, lift. One shelf at a time.

Short answer: Confirm the rack is anchored, extend one shelf fully, confirm it is locked, lift straight, set the die centered, and roll the shelf home.

  1. Confirm the rack is bolted down. Never load or extend a shelf on a rack that is not anchored.
  2. Extend one shelf fully. MECO shelves roll out one at a time and lock when extended. Do not open a second shelf.
  3. Confirm it is locked. The shelf must not roll back during the lift.
  4. Lift straight. Up by crane or straight back by fork truck. Do not drag a die across the shelf.
  5. Set the die centered, square to the frame, with nothing overhanging.
  6. Roll the shelf fully home before moving to the next one.
Never stand under a suspended die

Rigging, crane and fork truck practice are governed by your plant procedures and the OSHA rules for that equipment. The rack makes the lift easier. It does not replace them.

A die cart or lift table at the height of the extended shelf lets you roll a die off without a second crane lift. See our lift tables guide and mobile lift equipment guide.

Section Nine

Aisle, floor and anchoring

A full rack is a very heavy, concentrated load, and it has to be bolted down.

Short answer: Allow the shelf depth plus your equipment's working room in front of the rack, check the floor for the loaded weight, and anchor every upright.

Clear space in front = shelf depth + equipment working room
Example
A 48 in deep shelf and a fork truck that needs 10 ft to approach and square up: 4 ft + 10 ft = 14 ft. Use your own truck's dimensions.

OSHA 1910.176(a) requires sufficient safe clearances for aisles where mechanical handling equipment is used.

Maximum loaded weight = rack weight + (levels × 2,000 lb)
RSR447-4 at full rating
1,570 + (5 × 2,000) = 11,570 lb, counting four shelves and the top
Footprint
About 56 in by 48 in, which is about 18.7 sq ft
Average over the footprint
11,570 ÷ 18.7 = about 620 lb per sq ft, carried on four uprights

That is our arithmetic from MECO's published ratings, not a MECO figure. On a sound ground-floor slab it is usually not a problem. On a mezzanine, an upper floor or a cracked slab, have the floor checked for the loaded weight before installation.

No anchors, no load

A shelf extended with 2,000 lb on it puts that weight in front of the frame, which can tip an unanchored rack. Bolt every upright to sound concrete before a shelf is loaded or extended. OSHA 1910.176(b) requires that storage of material not create a hazard.

Section Ten

Freight, assembly and weight

These racks arrive heavy, flat and on a truck.

Short answer: Plan for a fork truck at delivery, anchors and a hammer drill on installation day, and consider MECO's assembled option.

  • Weight: MECO starters weigh 921 lb to 1,570 lb and add-ons 852 lb to 1,474 lb.
  • Delivery: have a fork truck at the dock. These do not come off a truck by hand.
  • Assembly: a knocked-down rack needs two or more people and lifting equipment. MECO also offers assembled units, quoted on request.
  • Finish: MECO units are gray enamel.
Section Eleven

Common and costly mistakes

What goes wrong on roll-out rack orders.

Short answer: Weigh the die, size the shelf to the full footprint, order one starter per row, and anchor before loading.

Using a nominal die weight

Weigh the complete set as it will sit on the shelf.

Letting dies overhang

Overhang catches the frame when the shelf rolls in.

Choosing the 85 in unit without checking openings

Four shelves means shorter openings.

Ordering three starters for three bays

One starter and two add-ons.

Mixing sizes in a row

Add-ons must match the height and depth.

Forgetting the extended shelf in the aisle

A 48 in shelf plus a fork truck needs real floor space.

Opening two shelves at once

One shelf out, locked, then rolled home.

Not bolting the rack down

Anchor before any shelf is loaded or extended.

Ignoring the floor

A loaded four-shelf MECO rack can pass 11,000 lb.

Comparing quotes by size alone

Compare full model numbers, starter or add-on, assembled or knocked down, and freight.

Section Twelve

Frequently asked questions

The questions that come up most on roll-out rack quotes.

How much weight does each shelf hold?

2,000 lb per shelf on both MECO and Jarke racks. Jarke states the rating holds at full extension. MECO also rates the top of the unit at 2,000 lb.

Do the shelves pull out all the way?

Yes. MECO and Jarke both list 100% shelf extension, so the shelf comes clear of the frame and the shelf above.

Do MECO shelves lock when extended?

Yes. MECO states its 10 gauge steel shelves roll out one at a time and lock in the extended position.

What do the numbers in a MECO model number mean?

After RSR, the first digit is the shelf width and the second is the depth (3 is 36 in, 4 is 48 in). The third is the height (5 is 62 in, 6 is 72 in, 7 is 85 in). The number after the dash is the shelf count, and A means add-on.

What is the difference between a starter and an add-on?

A starter is a complete freestanding rack. An add-on shares an upright with the unit next to it. A row is one starter plus any number of add-ons.

How do I load and unload the shelves?

Extend one shelf fully, confirm it is locked, then lift by overhead crane or fork truck. Roll the shelf home before opening another.

Can I adjust the shelf heights?

Yes. MECO's structural channel frame adjusts in 2 in steps, and Jarke shelves adjust on 2 in centers.

What shelf sizes are available?

MECO lists 36 by 36, 36 by 48, 48 by 36 and 48 by 48 in shelves, width by depth. Jarke lists 36 by 36, 48 by 36 and 48 by 48 in.

Do the racks need to be anchored?

Yes. A loaded shelf at full extension puts 2,000 lb in front of the frame, and an unanchored rack can tip. Bolt every upright to sound concrete before loading or extending a shelf.

How heavy are the racks?

MECO starters weigh 921 lb to 1,570 lb and add-ons 852 lb to 1,474 lb. A four-shelf rack at full rating, with the top loaded, is about 11,570 lb.

What if my dies weigh more than 2,000 lb?

A roll-out shelf rack is the wrong product. Heavier dies need racking engineered for the load. Call us with the die weights and sizes.

Section Thirteen

Quick-reference tables

The figures on one screen.

MECO Roll-Out Shelf Rack, as published by MECO
Specification Published
Shelf capacity 2,000 lb per shelf
Top of unit Up to 2,000 lb
Extension 100%, shelves lock when extended
Frame Structural 3 in channel, 2 in adjustment
Shelves 10 gauge steel
Shelf sizes 36 by 36, 36 by 48, 48 by 36, 48 by 48 in
Heights 62 in and 72 in with 3 shelves, 85 in with 4
Starter width Shelf width + 8 in
Weights Starters 921 to 1,570 lb, add-ons 852 to 1,474 lb
Before you order

Tell us the weight and footprint of your largest die, the tallest die, how you load, the space in front of the rack and the floor it stands on.

About the author. Tom McGovern has worked in the industrial material handling industry since 1981, bringing over 45 years of hands-on experience helping businesses select the right equipment for their applications. His expertise includes specifying and quoting MECO roll-out die racks and Jarke E-Z Glide shelving.

Questions about this guide? Call 866-333-0728 to speak with an experienced material handling specialist.

Ready for a quote?

Send us these details and a material handling specialist will reply, typically within one business day.

  • Dimensions
    Size of the load and the space it goes in
  • Load
    Weight per item, shelf or level
  • Quantity
    How many units you need
  • Delivery ZIP code
    For freight pricing
  • Drawing
    A sketch, photo or spec sheet, if you have one
Get a Fast Quote Call 866-333-0728

Tell us your biggest die

Weight, footprint and height of the largest die, how you load it, and the floor. We will match the shelf size, height and number of bays. Quotes are reviewed by material handling specialists, typically within one business day.

866-333-0728

Browse roll-out die racks at custommhs.com

No bots. No guesswork. Real experts.

Sources

OSHA 29 CFR 1910.176 · MECO-Omaha and Jarke figures as published by the manufacturers and on CustomMHS product listings.

Disclaimer. This guide is educational content and reflects the opinion and general experience of CustomMHS. It is not a structural or floor loading assessment. Have the floor checked where there is any doubt, anchor every rack as the manufacturer directs, and follow your plant procedures for rigging and lifting. Reviewed November 2026.